SLIN-06F1A0G

NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 SLIN-06F1Ax RoHS Compliant Rev.E Features  Wide Input Voltage Range  Ability to Sink and Source Current  Fixed Switching Frequency  Cost Efficient Open Frame Design  Remote Sense  Over Temperature Protection  Remote On/Off  Output Over Current Protection TM  Tunable Loop  Flexible output voltage sequencing  Compliant to IPC-9592 (September 2008), Category 2, Class II  Compliant to RoHS EU Directive 2002/95/EC  Compatible in a Pb-free or SnPb reflow environment to Optimize Dynamic output voltage response  Certificated to UL60950-1/CSA C22.2 No.60950-1, 2rd  VDE 0805:2001-12 (EN60950-1) Licensed Applications    Distributed power architectures Intermediate bus voltage applications Telecommunications equipment    Servers and storage applications Networking equipment Industrial equipment Description The SLIN-06F1Ax power modules are non-isolated dc-dc converters that can deliver up to 6A of output current. These modules operate over a wide range of input voltage (VIN=2.4Vdc-5.5Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 3.63Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection, and output voltage sequencing. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Part Selection Output Voltage Input Voltage Max. Output Current Typical Efficiency Model Number Active High Model Number Active Low 0.6 Vdc – 3.63 Vdc 2.4 Vdc - 5.5 Vdc 6A 91% SLIN-06F1A0 SLIN-06F1AL Notes: 1. Add “R” suffix at the end of the model number to indicate tape and reel packaging (Standard). 2. Add “G” suffix at the end of the model number to indicate tray packaging (Option). Ordering Part Number S LIN – 06 F 1A 0 x 1 2 3 4 5 6 7 1---Surface mount 2---Series code 3---Output current (6A) 4--- Wide input voltage range (2.4-5.5V) 5--- With sequencing 6--- Enable, active high, change “0” to “L” means active low 7--- Package Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 1 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 Absolute Maximum Ratings Min Typ Max Unit Continuous Input Voltage -0.3 - 6 V Sequencing Voltage -0.3 - Vin V Operating Ambient Temperature -40 - 85 C Storage Temperature -55 - 125 C - - 2000 m Parameter Altitude Notes Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Input Specifications Min Typ Max Unit Operating Input Voltage Parameter 2.4 - 5.5 V Input Current (full load) - - 6.5 A - 30 75 - - 2.2 - mA mA mA Notes VIN=2.4V to 5.5V Input Current (no load) Vo=0.6V Vo=3.3V Input Stand-by Current Input Reflected Ripple Current (pk-pk) - 25 - I2t Inrush Current Transient - - 1 A2s Input Ripple Rejection (120Hz) - 40 - dB Turn-on Threshold - - 2.2 V Turn-off Threshold 1.75 - - V Hysteresis 0.08 - 0.2 V mA VIN=5.0V, module enabled VIN = 5.0Vdc, module disabled 5Hz to 20MHz, 1uH source impedance; VIN =0 to 5.5V, IO = IOmax ; See Test Configurations CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 2 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 Output Specifications Parameter Min Typ Max Unit Output Voltage Set Point -1.5 - +1.5 %Vo,set Output Voltage -3.0 - +3.0 %Vo,set Adjustment Range 0.6 - 3.63 V - - 0.5 V VO ≥ 2.5V VO < 2.5V - - 10 5 mV mV VO ≥ 2.5V VO < 2.5V - - 0.4 10 %Vo,set mV Temperature Regulation (-40°C to +85°C) - - 0.4 %Vo,set Ripple and Noise (pk-pk) - 25 35 mV Remote Sense Range Notes with 0.5% tolerance for external resistor used to set output voltage Over all operating input voltage, resistive load, and temperature conditions until end of life selected by an external resistor Load Regulation IO=IO, min to IO, max Line Regulation VIN=V IN, min to VIN, max 5Hz to 20MHz BW, V IN=V IN, nom and IO=IO, to IO, max Co = 0.1uF // 10 uF ceramic capacitors) min Ripple and Noise (rms) - 10 15 mV Output Current Range 0 - 6 A Output DC Current Limit - - 200 %Io,max Output Short-Circuit Current - 0.23 - A Vo≤250mV, Hiccup Mode Output Capacitance ESR≥ 1 mΩ ESR≥0.15 mΩ ESR≥ 10 mΩ 0 0 0 - 47 1000 3000 uF uF uF - 2 - mS - 2 - mS Without the Tunable Loop TM With the Tunable Loop With the Tunable LoopTM Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = V IN, min until Vo =10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo =10% of Vo, set) Output voltage Rise time - 5 - mS Output voltage overshoot - - 3 %Vo,set Turn-On Delay Time Hiccup Mode TM time for Vo to rise from10% of Vo, set to 90% of Vo, set Vin=Vin, min to Vin, max, Io=Io, min to Io, max, With or without maximum external capacitance Dynamic Load Response △V0%~50% of Peak Deviation - 180 - Max Load Settling Time - 20 - mV uS △V50%~0% of Peak Deviation - 170 - mV Max Load Settling Time - 20 - uS di/dt=10A/us, Vin=5V, Vo=1.8V, Ta=25°C, Co=0 Notes: 1. External capacitors may require using the new Tunable Loop TM feature to ensure that the module is stable as well as getting the best transient response (See the Tunable LoopTM section for details). 2. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 3 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 General Specifications Parameter Min Typ Max Unit Notes - 72.3 82.7 87.7 91.4 93.0 - % % % % % Switching Frequency - 600 - kHz Over Temperature Protection - 140 - C 10 - - msec Delay from VIN, min to application of voltage on SEQ pin Tracking Accuracy Power-Up: 2V/ms Power-Down: 2V/ms - - 100 100 mV mV Vin, min to Vin, max; Io, min to Io, max, Vseq < Vo Weight - 1.95 - g Efficiency Vo=0.6V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V Sequencing Delay time MTBF 34,602,572 hours 0.48 x 0.48 x 0.29 12.19 x 12.19 x 7.25 - Vin= 3.3Vdc, Ta=25°C Io=Io, max , Vo= Vo,set. When Vo=3.3V, Vin=5.0V Calculated Per Bell Core SR-332 (Io=Io, max, Ta=40°C, Telecordia Issue 2 Method 1 Case 3) Dimensions Inches (L × W × H) Millimeters (L × W × H) Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 4 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 Efficiency Data 95 86 84 90 EFFICIENCY,  (%) EFFICIENCY,  (%) 82 80 78 76 Vin=2.4V 74 Vin=3.3V Vin=5.5V 72 70 85 80 Vin=2.4V Vin=3.3V Vin=5.5V 75 70 0 1 2 3 4 5 6 0 1 OUTPUT CURRENT, IO (A) 2 3 4 5 6 OUTPUT CURRENT, IO (A) Vo=0.6V Vo=1.2V 100 95 95 EFFICIENCY,  (%) EFFICIENCY,  (%) ) 90 Vin=2.4V 85 Vin=3.3V Vin=5.5V 80 75 90 Vin=3V 85 Vin=3.3V Vin=5.5V 80 75 70 70 0 1 2 3 4 5 6 OUTPUT CURRENT, IO (A) 0 1 2 3 4 5 6 OUTPUT CURRENT, IO (A) Vo=1.8V Vo=2.5V 100 EFFICIENCY,  (%) ) 95 90 Vin=5.5V Vin=5V 85 Vin=4V 80 75 70 0 1 2 3 4 5 6 OUTPUT CURRENT, IO (A) Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 5 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 6.2 6.2 6.0 6.0 5.8 0.5m/s (100LFM) OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) Thermal Derating Curves NC 5.6 5.4 5.2 5.0 20 30 40 50 60 70 80 5.8 0.5m/s (100LFM) 5.4 5.2 5.0 90 20 30 O 40 6.0 6.0 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) 6.2 NC 5.6 5.4 5.2 5.0 40 50 70 80 90 80 90 Vo=1.2V 6.2 30 60 AMBIENT TEMPERATURE, T A C Vo=0.6V 20 50 O AMBIENT TEMPERATURE, T A C 5.8 NC 5.6 60 70 80 90 O 5.8 NC 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O AMBIENT TEMPERATURE, T A C AMBIENT TEMPERATURE, T A C Vo=1.8V Vo=2.5V OUTPUT CURRENT, Io (A) 6.2 6.0 5.8 NC 5.6 5.4 5.2 5.0 20 30 40 50 60 70 80 90 O AMBIENT TEMPERATURE, T A C Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 6 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 OUTPUT VOLTAGE VO (V) (20Mv/div) OUTPUT VOLTAGE VO (V) (20Mv/div) Ripple and Noise Waveforms TIME, t (1s/div) TIME, t (1s/div) Vin=5V, Vo=1.2V, Io = Io,max OUTPUT VOLTAGE VO (V) (20Mv/div) OUTPUT VOLTAGE VO (V) (20Mv/div) Vin=5V, Vo=0.6V, Io = Io,max TIME, t (1s/div) Vin=5V, Vo=2.5V, Io = Io,max OUTPUT VOLTAGE VO (V) (20Mv/div) Vin=5V, Vo=1.8V, Io = Io,max TIME, t (1s/div) TIME, t (1s/div) Vin=5V, Vo=3.3V, Io = Io,max Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 7 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 OUTPUT CURRENT, IO (A) (2A/div) OUTPUT VOLTAGE V O (V) (100Mv/div) TIME, t (20s /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.2V OUTPUT VOLTAGE VO (V) (200Mv/div) OUTPUT VOLTAGE VO (V) (100Mv/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=0.6V OUTPUT CURRENT, IO (A) (2A/div) TIME, t (20s /div) TIME, t (20s /div) TIME, t (20s /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=2.5V OUTPUT CURRENT, IO (A) (2A/div) OUTPUT VOLTAGE VO (V) (200Mv/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.8V OUTPUT CURRENT, IO (A) (2A/div) OUTPUT CURRENT, IO (A) (2A/div) OUTPUT VOLTAGE V O (V) (100Mv/div) Transient Response Waveforms TIME, t (20s /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 8 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500Mv/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=0.6V TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) V O (V) (1V/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=1.8V ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500Mv/div) TIME, t (1 ms/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=1.2V ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (1V/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (200Mv/div) Startup Time TIME, t (5 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=2.5V TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 9 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 INPUT VOLTAGE OUTPUT VOLTAGE VIN (V) (2V/div) VO (V) (1V/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=0.6V TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VIN (V) (2V/div) VO (V) (1V/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.8V INPUT VOLTAGE OUTPUT VOLTAGE VIN (V) (2V/div) VO (V) (500Mv/div) TIME, t (1 ms/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.2V INPUT VOLTAGE OUTPUT VOLTAGE VIN (V) (2V/div) VO (V) (1V/div) INPUT VOLTAGE VIN (V) (2V/div) OUTPUT VOLTAGE VO (V) (200Mv/div) Startup Time (continued) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=2.5V TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 10 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Jul. 17, 2015 Test Configurations Input Reflected Ripple Current Test Setup. CURRENT PROBE TO OSCILLOSCOPE LTEST VIN(+) BATTERY 1μH CIN CS 1000μF Electrolytic 2x100μF Tantalum E.S.R.