SLIN-50E1ALG

NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 SLIN-50E1AL RoHS Compliant Rev.E Features  Wide Input Voltage Range  Output Voltage Sequencing  Monotonic Start-up  Over Temperature Protection  Negative Remote On/Off  Output Over Current Protection  True Differential Remote Sense  Tunable Loop (a registered trademark of Lineage Power Systems) to Optimize Dynamic output voltage response  Compliant to IPC-9592 (September 2008), Category 2, Class II  Parallel Operation With Active Current Sharing TM  Compliant to RoHS EU Directive 2002/95/EC  UL* 60950 Recognized, CSA† C22.2 No. 60950-1-07 Certified  VDE‡ 0805 (EN60950-1 2nd edition) Licensed Applications   Distributed power architectures Intermediate bus voltage applications   Telecommunications equipment Industrial applications Description The SLIN-50E1AL power modules are non-isolated dc/dc converters that can deliver up to 50 A of output current. These modules operate over a wide range of input voltage (VIN = 4.5 Vdc-14 Vdc) and provide a precisely regulated output voltage from 0.7 Vdc to 2.0 Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection, output voltage sequencing and paralleling. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Part Selection Output Voltage Input Voltage 0.7 Vdc - 2 Vdc 4.5 Vdc - 14 Vdc Max. Output Current 50 A Typical Efficiency 87% Model Number Active Low SLIN-50E1AL Notes: 1. Add “R” suffix at the end of the model number to indicate tape and reel packaging (Standard). 2. Add “G” suffix at the end of the model number to indicate tray packaging (Option). Ordering Part Number S LIN – 50 E 1A L x 1 2 3 4 5 6 7 1---Surface mount 4--- Wide input voltage range (4.5-14V) 2---Series code 5--- Wide output voltage range (0.7-2V) 3---Output current (50A) 6--- Enable, active low 7---Package, “G” for Tray Packaging, “R” for Reel Packaging Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 1 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 Absolute Maximum Ratings Min Typ Max Unit Continuous Input Voltage -0.3 - 14 V Sequencing Pin Voltage -0.3 - 4 V Operating Ambient Temperature -40 - 85 C Storage Temperature -55 - 125 C - - 2000 m Parameter Altitude Notes Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Input Specifications Parameter Operating Input Voltage Min 4.5 Typ - Max 14 Unit V Input Current (full load) - - 26 A - 73.4 - mA - 136 - mA - 1.3 - mA VIN = VIN,mon , module disabled 5Hz to 20MHz, 1μH source impedance; VIN,min to VIN,max, IO= IOmax Input Current (no load) Input Stand-by Current Input Reflected Ripple Current (pk-pk) - - 73 mA I t Inrush Current Transient - - 1 As Input Ripple Rejection (120Hz) - 50 - dB Turn-on Threshold - 4.26 - V Turn-off Threshold - 4.04 - V Hysteresis - 0.22 - V 2 Notes VIN= VIN,min to VIN,max, IO = IO,max Vo=0.7V, VIN= V IN,mon, IO=0 module enabled Vo=1.8V, VIN= V IN,mon, IO=0 module enabled 2 CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a surface mount, fast acting fuse with a maximum rating of 30A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 2 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 Output Specifications Parameter Min Typ Max Unit Notes Output Voltage Set Point -1.0 - +1.0 %Vo,set VIN=VIN,nom, IO=IO, nom, T ref=25°C. Output Voltage -2.0 - +2.0 %Vo,set Over all operating input voltage, resistive load, and temperature conditions until end of life Adjustment Range 0.7 - 2.0 V Remote Sense Range - - 0.5 V Load Regulation - - 8 mV IO=IO, min to IO, max Line Regulation - - 5 mV VIN=VIN, min to VIN, max Temperature Regulation (-40°C to 85°C) - - 8 mV Tref=TA, min to TA, max Ripple and Noise (pk-pk) - - 50 mV 5Hz to 20MHz BW, VIN=VIN, nom and IO =IO, min to IO, max, Co = 1μF // 10 μF ceramic capacitors Output Current Range 0 - 50 A Output DC Current Limit - 180 - %Io,max Output Short-Circuit Current - 5.5 - A Vo≤250mV, Hiccup Mode Output Capacitance ESR≥1 mΩ ESR≥10 mΩ ESR≥1 mΩ ESR≥10 mΩ - - 1200 10000 20000 20000 uF uF uF uF Without the Tunable Loop TM Without the Tunable Loop TM With the Tunable Loop With the Tunable Loop TM - 4.8 - mS - 4.8 - mS Output voltage Rise time - 3.6 - mS Output voltage overshoot - - 3 %Vo,set selected by an external resistor Hiccup Mode TM Case 1: On/Off input is set to Logic Low (Module Turn-On Delay Time ON) and then input power is applied (delay from instant at which VIN =V IN, min until Vo=10% of Vo,set) Case 2: Input power is applied for at least one second and then the On/Off input is set to logic Low (delay from instant at which Von/Off=0.3V until Vo=10% of Vo, set) time for Vo to rise from 10% of Vo, set to 90% of Vo, set Io=Io, max,Vin=4.5 to 14Vdc, Ta=25°C Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 3 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 General Specifications Parameter Min Typ Max Unit - 81.1 87.0 90.1 - % % % Switching Frequency - 260 - kHz Over Temperature Protection - 125 - C Sequencing Slew rate capability - - 2 V/mS 10 - - mS - 100 200 200 400 mV mV - 5 112.5 87.5 - V %Vo,set %Vo,set Forced Load Share Accuracy - 10 - %Io Number of Units in Parallel - - 5 - Weight - 14.22 - g Efficiency Vo=0.7V Vo=1.2V Vo=1.8V Sequencing Delay time Tracking Accuracy Power-Up: 2V/ms Power-Down: 1V/ms PGOOD (Power Good) Internal pull-up, VPGOOD Overvoltage threshold for PGOOD Undervoltage threshold for PGOOD MTBF 4,755,661 Hours 1.30 x 0.90 x 0.34 33 x 22.9 x 10 - Notes Vin= 12Vdc, Ta=25°C Io=Io, max , Vo= Vo,set VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo Delay from VIN, min to application of voltage on SEQ pin VIN, min to VIN, max; IO, min - IO, max VSEQ < Vo Calculated MTBF (IO=IO, max, Ta=40°C) per Telecordia Issue 2, Method I, Case 3 Dimensions Inches (L × W × H) Millimeters (L × W × H) Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 4 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 95 95 90 90 EFFICIENCY,  (%) EFFICIENCY,  (%) Efficiency Data 85 Vin=12V 80 Vin=4.5V Vin=14V 75 70 Vin=12V 85 Vin=14V 80 Vin=4.5V 75 70 0 10 20 30 40 50 OUTPUT CURRENT, I O (A) 0 10 20 30 40 50 OUTPUT CURRENT, IO (A) Vo=0.7V, T a=25°C Vo=1.2V, Ta=25°C 100 Vin=12V EFFICIENCY,  (%) 95 90 85 Vin=14V Vin=4.5V 80 75 70 0 10 20 30 40 50 OUTPUT CURRENT, I O (A) Vo=1.8V, T a=25°C Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 5 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 55 55 50 50 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) Thermal Derating Curves 45 NC 40 0.5m/s (100LFM) 1.5m/s (300LFM) 35 1m /s ( 200LFM ) 30 2m/s (400LFM) 25 35 45 55 65 75 85 AMBIENT TEMPERATURE, TA OC 45 NC 40 0.5m/s (100LFM) 35 1m/s (200LFM) 30 1.5m/s (300LFM) 2m/s (400LFM) 25 35 45 55 65 75 85 AMBIENT TEMPERATURE, T A OC Vo=0.7V, Vin=12V Vo=1.2V, Vin=12V 55 OUTPUT CURRENT, Io (A) 50 45 40 NC 35 0.5m/s (100LFM) 30 1.5m/s 1m/s (300LFM) (200LFM) 2m/s (400LFM) 25 35 45 55 65 75 85 O AMBIENT TEMPERATURE, TA C Vo=1.8V, Vin=12V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 6 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE VO (V) (10mV/div) Ripple and Noise Waveforms TIME, t (1s/div) Vo=1.2V, Ta=25°C , Vin=12V, Io = Io,max OUTPUT VOLTAGE VO (V) (10mV/div) Vo=0.7V, T a=25°C , Vin=12V, Io = Io,max TIME, t (1s/div) TIME, t (1s/div) Vo=1.8V, Ta=25°C , Vin=12V, Io = Io,max Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 7 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT CURRENT, IO (A) (20A/div) OUTPUT CURRENT, IO (A) (20A/div) OUTPUT VOLTAGE VO (V) (10mV/div) Transient Response Waveforms TIME, t (0.2ms /div) TIME, t (0.1ms /div) Transient Response to Dynamic Load Change from 50% to 100%. Vo=1.2V, Ta=25°C, Vin=12V,Cext =5x47uF+ +13x330uFpolymer,CTune=120nF,RTune=180ohms OUTPUT CURRENT, IO (A) (20A/div) OUTPUT VOLTAGE V O (V) (20mV/div) Transient Response to Dynamic Load Change from 50% to 100%. Vo=0.7V, Ta=25°C, Vin=12V,Cext =5x47uF+ +22x330uFpolymer,CTune=330nF,RTune=100ohms TIME, t (0.1ms /div) Transient Response to Dynamic Load Change from 50% to 100%.Vo=1.8V, Ta=25°C, Vin=12V, Cext =5x47uF+ +8x330uFpolymer,CTune=47nF,RTune=220ohms Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 8 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 ON/OFF VOLTAGE VON/OFF (V) (5V/div) OUTPUT VOLTAGE Vo (V) (500mV/div) OUTPUT VOLTAGE Vo (V) (200mV/div) ON/OFF VOLTAGE VON/OFF (V) (5V/div) Startup Time TIME, t (2 ms/div) Start-up Using On/Off Voltage (Io = Io,max) Vo=1.2V, Vin = 12V, Ta=25°C OUTPUT VOLTAGE Vo (V) (500mV/div) ON/OFF VOLTAGE VON/OFF (V) (5V/div) Start-up Using On/Off Voltage (Io = Io,max) Vo=0.7V, Vin = 12V, Ta=25°C TIME, t (2 ms/div) TIME, t (2 ms/div) Start-up Using On/Off Voltage (Io = Io,max) Vo=1.8V, Vin = 12V, Ta=25°C Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 9 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 INPUT VOLTAGE VIN (V) (5V/div) OUTPUT VOLTAGE Vo(V) (500mV/div) OUTPUT VOLTAGE Vo(V) (200mV/div) INPUT VOLTAGE VIN (V) (5V/div) Startup Time (continued) TIME, t (2 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=1.2V, Ta=25°C OUTPUT VOLTAGE Vo(V) (500mV/div) INPUT VOLTAGE VIN (V) (5V/div) Start-up Using Input Voltage (V IN = 12V, Io = Io,max ), Vo=0.7V, Ta=25°C TIME, t (2 ms/div) TIME, t (2 ms/div) Start-up Using Input Voltage (V IN = 12V, Io = Io,max ), Vo=1.8V, Ta=25°C Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302  Tel 201-432-0463  Fax 201-432-9542  www.belfuse.com 10 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.7 Vdc – 2 Vdc /50 A Outputs Bel Power Inc., a subsidiary of Bel Fuse Inc. Jul. 17 2015 Test Configurations Input Reflected Ripple Current Test Setup. CURRENT PROBE TO OSCILLOSCOPE LTES T VIN(+) BATTERY 1μH CIN CS 1000μF Electrolytic 2x100μF Tantalum E.S.R.