1WS-2409

DC-DC Converter UNIT 1W Series ( 1W WIDE INPUT RANGE DC-DC CONVERTER ) FEATURES 1000VDC ISOLATION HIGH EFFICIENCY INTERNAL FILTERING LOW COST NO EXTERNAL COMPONENTS REQUIRED UP TO 2W REGULATED OUTPUT POWER SINGLE IN LINE PACKAGE 100% BURNED IN LOW NOISE MTBF > 1,000,000 HOURS OUTPUT SPECIFICATIONS Voltage Setpoint Accuracy Temperature Coefficient Ripple & Noise (20MHz BW) Line Regulation1 Load Regulation 2 INPUT SPECIFICATIONS +/-2% max +/-0.03%/ C O Input Voltage Range Input Filter 2:1 INPUT RANGE Pi Network 100mVp-p max +/-0.2% max +/-0.2% max Continuous GENERAL SPECIFICATIONS Efficiency Isolation Voltage 3 Short Circuit Protection 70% min 1000 VDC min 9 10 ohms min 75 KHz min 80pF max 1,000,000 Hours 6.6g Typ Non-Conductive Plastic 31.8mm*8.6mm*14.5mm ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Cooling -25 C to +71 C O O Isolation Resistance Switching Frequency Isolation Capacitance MTBF Weight -55 OC to +125 OC Free-Air Convection ALL SPECIFICATIONS TYPICAL AT NOMINAL LINE, FULL LOAD , AND 25 O Case Material Case Size C UNLESS OTHERWISE NOTED. 1 2 3 High Line to Low Line. Load Regulation is for output load current change from 10% to 100%. For 60 seconds www.Power-Systems.de Page: 1 / 4 Version: 4-Oct-02 DC-DC Converter UNIT 1W Series ( 1W WIDE INPUT RANGE DC-DC CONVERTER ) SELECTION GUIDE 2W OUTPUT MODEL NUMBER INPUT (VDC) 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 OUTPUT (VDC) 5 9 12 15 5 9 12 15 OUTPUT (mA) 400 222 168 133 400 222 168 133 INPUT CURRENT(mA) FULL LOAD NO LOAD 20 20 20 20 12 13 11 11 72 74 78 78 74 75 78 78 1000 1000 1000 1000 1000 1000 1000 1000 VOLTAGE VOLTAGE CURRENT EFF (%) ISOLATION (VDC) 1WS-1205 1WS-1209 1WS-1212 1WS-1215 1WS-2405 1WS-2409 1WS-2412 1WS-2415 231 225 213 213 112 111 107 107 Note: Other input to output voltages may be available. Please contact factory. MECHANICAL DIMENSIONS PIN 1 3 6 8 10 12 SINGLE +Vin -Vin NC NC +Vout -Vout www.Power-Systems.de Page: 2 / 4 Version: 4-Oct-02 DC-DC Converter UNIT 1W Series ( 1W WIDE INPUT RANGE DC-DC CONVERTER ) RECOMMENDED FOOTPRINT DETAILS SIMPLIFIED SCHEMATIC +Vin +Vout TYPICAL APPLICATIONS INPUT +Vin +Vout OUTPUT -Vout -Vin PFM CONTROLLER ISOLATION REFERENCE & ERROR AMP DC-DC CONVERTER -Vin -Vout LOAD TEMPERATURE DERATING 2.5 OUTPUT POWER(W) 2.0 1.5 1.0 0.5 0.0 -25 0 SAFE OPERATING AREA 25 50 70 100 TA(degree C) www.Power-Systems.de Page: 3 / 4 Version: 4-Oct-02 DC-DC Converter UNIT 1W Series ( 1W WIDE INPUT RANGE DC-DC CONVERTER ) 1W SERIES APPLICATION NOTES: EXTERNAL CAPACITANCE REQUIREMENTS: No external capacitance is required for operation of the 1W series. To meet the reflected ripple requirements of the converter, an input impedance of less than 0.5 ohm from DC to 100KHz is required. External output capacitance is not required for operation, however it is recommended that 10uF tantalum and 0.1uF ceramic capacitance be selected for reduced system noise. Additional output capacitance may be added for increased filtering, but should not exceed 220uF. Negative Outputs: A negative output voltage may be obtained by connecting the +OUT to circuit ground and connecting –OUT as the negative output. FOR MORE INFORMATION CALL: Power Systems – The Power Solution 74360 Ilsfeld-Auenstein ( Germany ) Dörnet 8 E-mail: Info@Power-Systems.de Tel: + 49 / 70 62 / 67 59 – 6 Fax: + 49 / 70 62 / 67 59 -80 Home Page: www.Power-Systems.de www.Power-Systems.de Page: 4 / 4 Version: 4-Oct-02