CXA-P1212-VJL

DC-AC INVERTER UNIT CXA-0217 (CXA-P1212-VJL) (7W DUAL OUTPUTS WITH DIMMING FUNCTION) (PRELIMINARY INFORMATION) DESCRIPTION : This DC to AC Inverter was developed for large size LCD panel as Multiple Media, Replacement of CRT Monitor and other general Purpose . APPLICABLE LCD: 11 to 14 inches Double lamps type Lamp Voltage 660V Lamp Current 6mA FEATURES : Current Feedback Circuit High Efficiency Low noise with voltage resonant circuit Regulated output current Output Current Feedback Circuit for each Lamp 8mm Low Profile. TEMPERATURE & HUMDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : 180.0 ± 0,5 146.5 ±0.2 3.5 ±0.5 80 ±0.2 Unit : mm Weight : 30 (g) typ. 0 °C ~ +70 °C -30 °C ~ +85 °C 95 %RH max 2 5.0 ± 0.3 18 ± 0.2 CN3 1 1 CN1 4 3-φ3 ±0.2 2 1 3 CN2 1 No. 1 2 3 4 3.5 ±0.5 Part Discription PCB Connector CN1 Connector CN2 Connector CN3 Qty. 1 1 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-SM3 SM02(8.0)B-BHS-1 SM02(8.0)B-BHS-1 Note t=1mm JST JST JST Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page ( 1 / 4 ) Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 VER, 16 December 2002 All specification are subject to change without notice. 8 m ax DC-AC INVERTER UNIT CXA-0217 (CXA-P1212-VJL) (7W DUAL OUTPUTS WITH DIMMING FUNCTION) (PRELIMINARY INFORMATION) Input Side CN1: Output Side CN2: Output Side CN3: Pin No. CN 3-1 CN 3-2 CN 3-3 Symbols Ratings V HIGH2 660 Vrms N.C. V LOW2 (2V) Pin No. Symbols CN 1-1 Vin CN 1-2 GND CN 1-3 Vbr CN 1-4 CN 1-5 Vrmt Ratings 9.6-14.4V 0V 0~3,4V N.C. Input 5V 0 ~0.4V: OFF 5 ,0~7,0: ON Pin No. CN 2-1 CN 2-2 CN 2-3 Symbols Ratings V HIGH1 660 Vrms N.C. V LOW1 (2V) ELECTRICAL CHARACTERISTICS : Conditions Items Output Current Input Current Frequency Open Circuit V oltage Dimming Function CN1-3 Impedance Insulation Resistance Dielectric S trength Symbols Vin (V) Vrmt (V) 12±2.4 12±1.2 12±2.4 12±1.2 12±2.4 12±1.2 12±2.4 12±1.2 12±2.4 12±1.2 Vbr (V) Ta (°C) 0 0~3.4 5~7 0 0~3.4 3.4 0~70 Specification RL1 (K Ω ) / Min. RL2 (K Ω ) 76~114 95±0.5 76~114 95 ∞ 250 5.3 5.5 52 Typ. Max. 6.0 6.0 0.76 0.76 58 6.7 6.5 1.3 1.2 64 Unit Iout1/2 Iin F Vopen Iout1/2 mArms A DC kHz Vrms 1400 1500 2000 1.65 1.7 100 1 2.0 2.0 11 - 2.45 mArms 2.4 kΩ MΩ kVrms Between CN1-2 and CN1-3 Impedance Between Input and PCB not pattern DC500V Between Input and PCB not pattern. Trip current 10mA for 1min. DIMMING CHARACTERISTICS (Reference) 7 6 Iout (mArms) 5 4 3 2 1 0 0,00 0,85 1,70 2,55 3,40 Vbr (VDC) Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page ( 2 / 4 ) Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 VER, 16 December 2002 All specification are subject to change without notice. DC-AC INVERTER UNIT CXA-0217 (CXA-P1212-VJL) (7W DUAL OUTPUTS WITH DIMMING FUNCTION) (PRELIMINARY INFORMATION) APPLICATION (for example) Voltage Dimming Type CN1-1(Vin) Vin 9.6~`14.4V SW Active On CN1-2(GND) CN2-3(Iout-ret) Vrmt 5V Vbr 0~5V CN1-5(Vrmt) CN3-1(Iout2) CN1-3(Vbr) CN1-4(NC) CN3-3(Iout-ret) CCFL2 RL2 CN2-1(Iout1) CCFL1 RL1 Resistor Dimming Type CN1-1(Vin) Vin 9.6~`14.4V SW Active On CN1-2(GND) CN2-3(Iout-ret) Vrmt 5V Vbr 10kΩ 5V CN1-5(Vrmt) CN3-1(Iout2) CN1-3(Vbr) CN1-4(NC) CN3-3(Iout-ret) CCFL2 RL2 CN2-1(Iout1) CCFL1 RL1 None Dimming Type CN1-1(Vin) Vin 9.6~`14.4V 1kΩ CN1-2(GND) CN2-3(Iout-ret) CN1-5(Vrmt) CN3-1(Iout2) 5V CN1-3(Vbr) CN1-4(NC) CN3-3(Iout-ret) CCFL2 RL2 CN2-1(Iout1) CCFL1 RL1 TEST CIRCUIT Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page ( 3 / 4 ) Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 VER, 16 December 2002 All specification are subject to change without notice. DC-AC INVERTER UNIT CXA-0217 (CXA-P1212-VJL) (7W DUAL OUTPUTS WITH DIMMING FUNCTION) (PRELIMINARY INFORMATION) Note 1. Note 2. For circuit connection , please prefer to test circuit diagram. Please use minimum of 2mm clearance (all directions) between inverter high voltage area and any conductors. Please refer to mechanical drawing for marking of high voltage area. Open voltage (strike voltage) is measured across the transformer secondary winding at no load as the reading at the output connector would be less than the actual value If the start up voltage falls below Cold Cathode Tube strike voltage , the CCFL will not light up easily specially at lower ambient temperature . Please review mounting instruction to avoid any abnormal operation due to coupling/leakage capacitance of inverter high voltage area to any surrounding conductor. Please check your lamp characteristic for minimum operational current and set the limit point in your design to avoid flickering and/or abnormal operation. For proper operation of circuit protection (FUSE or IC PROTECTOR), please use minimum of 2A capacity for input power supply. A start up sequence of Vrmt is the sametime of Vin turning on or after CN1-3 has brightness and remote functions. These functions are operated by voltage of Vbr as below: Luminance is max. at Vbr = 0V; Luminance is min. at Vbr = 3.4V Vbr ≥ 4.75V ⇒ No operation (Vrmt = 5~7V) Note 3. Note 4. Note 5. Note 6. Note 7. Note 8. Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page ( 4 / 4 ) Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 VER, 16 December 2002 All specification are subject to change without notice.