FWS-2403.3

DC-DC Converter UNIT FW Series ( 8 W WIDE INPUT RANGE DC-DC CONVERTER ) FEATURES 8W DIL PACKAGE 9-18V,18-36V,36-72V WIDE INPUT RANGE SHORT CIRCUIT PROTECTION LOW COST NO EXTERNAL COMPONENTS REQUIRED REGULATED OUTPUT TYPICAL EFFICIENCY 80% 100% BURNED IN INDUSTRY STANDARD PACKAGE MTBF > 700,000 HOURS OUTPUT SPECIFICATIONS Voltage Setpoint Accuracy Temperature Coefficient Ripple & Noise (20MHz BW) Line Regulation 1 2 INPUT SPECIFICATIONS +/-2% max +/-0.03%/ C O Input Voltage Range Input Filter 2:1 INPUT RANGE Pi Network 100mVp-p max +/-0.2% max +/-0.2% max Continuous Load Regulation GENERAL SPECIFICATIONS Efficiency Isolation Voltage 3 Short Circuit Protection 70% min 1000 VDC min 9 10 ohms min 50 KHz min 700,000 Hours 31.2g Typ Five-Side Shielded Case 50.8mm*25.4mm*11.2mm ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Cooling -25 C to +71 C O O Isolation Resistance Switching Frequency MTBF Weight Case Material -55 OC to +125 OC Free-Air Convection ALL SPECIFICATIONS TYPICAL AT NOMINAL LINE, FULL LOAD , AND 25 O Case Size C UNLESS OTHERWISE NOTED. 1 2 3 High Line to Low Line. Load Regulation is for output load current change from 10% to 100%. For 10 seconds www.Power-Systems.de Page: 1 / 5 Version: 4-Oct-02 DC-DC Converter UNIT FW Series ( 8 W WIDE INPUT RANGE DC-DC CONVERTER ) SELECTION GUIDE 8W OUTPUT MODEL NUMBER FWS-1203.3 FWS-1205 FWS-1209 FWS-1212 FWS-1215 FWD-1205 FWD-1209 FWD-1212 FWD-1215 FWS-2403.3 FWS-2405 FWS-2409 FWS-2412 FWS-2415 FWD-2405 FWD-2409 FWD-2412 FWD-2415 FWS-4803.3 FWS-4805 FWS-4809 FWS-4812 FWS-4815 FWD-4805 FWD-4812 FWD-4815 INPUT VOLTAGE (VDC) 9-18 9-18 9-18 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 36-72 36-72 OUTPUT VOLTAGE (VDC) 3.3 5 9 12 15 +/-5 +/-9 +/-12 +/-15 3.3 5 9 12 15 +/-5 +/-9 +/-12 +/-15 3.3 5 9 12 15 +/-5 +/-12 +/-15 OUTPUT CURRENT (mA) 2000 1600 888 670 533 +/-800 +/-444 +/-335 +/-267 2000 1600 888 670 533 +/-800 +/-444 +/-335 +/-267 2000 1600 888 670 533 +/-800 +/-335 +/-267 INPUT4 CURRENT(mA) FULL LOAD 753 888 813 813 803 867 860 813 803 367 422 402 402 402 422 420 402 402 183 210 201 201 201 201 201 201 NO LOAD 50 50 50 50 50 50 40 50 50 25 25 25 25 25 25 30 25 25 15 15 15 15 15 15 15 15 73 75 82 82 83 77 78 82 83 75 79 83 83 83 79 79 83 83 75 79 83 83 83 83 83 83 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 EFF (%) 5 ISOLATION (VDC) Note: Other input to output voltages may be available. Please contact factory. 4 5 NOMINAL INPUT VOLTAGE. NOMINAL INPUT VOLTAGE,FULL LOAD. www.Power-Systems.de Page: 2 / 5 Version: 4-Oct-02 DC-DC Converter UNIT FW Series ( 8 W WIDE INPUT RANGE DC-DC CONVERTER ) SIMPLIFIED SCHEMATIC SINGLE OUTPUT +Vin +Vout +Vin DUAL OUTPUT +Vout Common -Vout -Vin PFM CONTROLLER ISOLATION REFERENCE & ERROR AMP -Vout -Vin PFM CONTROLLER ISOLATION REFERENCE & ERROR AMP MECHANICAL DIMENSIONS PACKAGE PIN 1 2 3 4 5 SINGLE +Vin -Vin +Vout NO PIN -Vout DUAL +Vin -Vin +Vout Common -Vout RECOMMENDED FOOTPRINT DETAILS www.Power-Systems.de Page: 3 / 5 Version: 4-Oct-02 DC-DC Converter UNIT FW Series ( 8 W WIDE INPUT RANGE DC-DC CONVERTER ) TYPICAL APPLICATIONS SINGLE OUTPUT INPUT +Vin +Vout DUAL OUTPUT INPUT +Vin +Vout OUTPUT OUTPUT LOAD1 DC-DC CONVERTER -Vin -Vout LOAD DC-DC CONVERTER -Vin Common LOAD2 -Vout TEMPERATURE DERATING 8.0 OUTPUT POWER(W) 6.0 4.0 2.0 0.0 -25 0 SAFE OPERATING AREA 25 50 70 90 TA(degree C) FW SERIES APPLICATION NOTES: EXTERNAL CAPACITANCE REQUIREMENTS: No external capacitance is required for operation of the FW series. To meet the reflected ripple requirements of the converter, an input impedance of less than 0.5 ohm from DC to 220KHz is required. External output capacitance is not required for operation, however it is recommended that 10uF tantalum and 0.1uF ceramic capacitance be selected for reduced system noise. Additional output capacitance may be added for increased filtering, but should not exceed 220uF. www.Power-Systems.de Page: 4 / 5 Version: 4-Oct-02 DC-DC Converter UNIT FW Series ( 8 W WIDE INPUT RANGE DC-DC CONVERTER ) Negative Outputs: A negative output voltage may be obtained by connecting the +OUT to circuit ground and connecting –OUT as the negative output. FOR MORE INFORMATION CALL: Power Systems – The Power Solution Ilsfeld-Auenstein ( Germany ) Dörnet 8 E-mail: Info@Power-Systems.de Tel: + 49 / 70 62 / 67 59 – 6 Fax: + 49 / 70 62 / 67 59 -80 Home Page: www.Power-Systems.de www.Power-Systems.de Page: 5 / 5 Version: 4-Oct-02