KWD-1215T

DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) FEATURES 15W DIL PACKAGE 9-18V,18-36V,36-72V WIDE INPUT RANGE SHORT CIRCUIT PROTECTION LOW COST NO EXTERNAL COMPONENTS REQUIRED REGULATED OUTPUT TYPICAL EFFICIENCY 80% 100% BURNED IN INDUSTRY STANDARD PACKAGE MTBF > 700,000 HOURS OUTPUT SPECIFICATIONS Voltage Setpoint Accuracy Temperature Coefficient Ripple & Noise (20MHz BW) Line Regulation 1 2 INPUT SPECIFICATIONS +/-3% max +/-0.03%/ OC Input Voltage Range Input Filter 2:1 INPUT RANGE Pi Network 100mVp-p max +/-0.2% max +/-0.2% max Continuous Load Regulation GENERAL SPECIFICATIONS Efficiency Isolation Voltage 3 Short Circuit Protection 70% min 1000 VDC min 9 10 ohms min 200 KHz min 700,000 Hours 60.0g Typ Six-Side Shielded Case 50.8mm*50.8mm*11mm ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Cooling -25 OC to +71 OC -55 OC to +100 OC Free-Air Convection Isolation Resistance Switching Frequency MTBF Weight Case Material ALL SPECIFICATIONS TYPICAL AT NOMINAL LINE, FULL LOAD , AND 25 O Case Size C UNLESS OTHERWISE NOTED. 1 2 3 High Line to Low Line. Load Regulation is for output load current change from 10% to 100%. For 10 seconds www.Power-Systems.de Page: 1 / 6 Version: 4-Oct-02 DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) SELECTION GUIDE(1) 2:1 15W OUTPUT MODEL NUMBER KWS-1205 KWS-1209 KWS-1212 KWS-1215 KWS-1224 KWD-1205 KWD-1212 KWD-1215 KWD-1224 KWS-2405 KWS-2412 KWS-2415 KWS-2424 KWD-2405 KWD-2412 KWD-2415 KWD-2424 KWS-4805 KWS-4812 KWS-4815 KWS-4824 KWD-4805 KWD-4812 KWD-4815 KWD-4824 INPUT VOLTAGE (VDC) 9-18 9-18 9-18 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 36-72 36-72 OUTPUT VOLTAGE (VDC) 5 9 12 15 24 +/-5 +/-12 +/-15 +/-24 5 12 15 24 +/-5 +/-12 +/-15 +/-24 5 12 15 24 +/-5 +/-12 +/-15 +/-24 OUTPUT CURRENT (mA) 3000 1670 1250 1000 625 +/-1500 +/-625 +/-500 +/-313 3000 1250 1000 625 +/-1500 +/-625 +/-500 +/-313 3000 1250 1000 625 +/-1500 +/-625 +/-500 +/-313 INPUT4 CURRENT(mA) FULL LOAD 1623 1580 1563 1545 1543 1623 1563 1525 1510 780 762 762 753 750 762 753 750 396 381 381 375 375 381 381 375 NO LOAD 40 30 40 38 38 40 40 38 38 20 18 18 18 20 18 18 20 10 9 9 9 10 9 9 9 77 79 80 81 81 77 80 82 83 80 82 82 83 83 82 83 83 79 82 82 83 83 82 82 83 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 EFF (%) 5 ISOLATION (VDC) Note: Other input to output voltages may be available. Please contact factory. 4 5 NOMINAL INPUT VOLTAGE. NOMINAL INPUT VOLTAGE,FULL LOAD. www.Power-Systems.de Page: 2 / 6 Version: 4-Oct-02 DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) SELECTION GUIDE(2) 4:1 15W OUTPUT MODEL NUMBER KWS-1205T KWS-1209T KWS-1212T KWS-1215T KWS-1224T KWD-1205T KWD-1212T KWD-1215T KWS-2405T KWS-2412T KWS-2415T KWD-2405T KWD-2412T KWD-2415T INPUT VOLTAGE (VDC) 9-36 9-36 9-36 9-36 9-36 9-36 9-36 9-36 18-72 18-72 18-72 18-72 18-72 18-72 OUTPUT VOLTAGE (VDC) 5 9 12 15 24 +/-5 +/-12 +/-15 5 12 15 +/-5 +/-12 +/-15 OUTPUT CURRENT (Ma) 3000 1670 1250 1000 625 +/-1500 +/-625 +/-500 3000 1250 1000 +/-1500 +/-625 +/-500 INPUT6 CURRENT(mA) FULL LOAD 1623 1600 1562 1562 1562 1623 1562 1562 791 771 762 791 771 762 NO LOAD 40 30 40 38 28 40 40 38 20 18 18 20 18 18 77 78 80 80 80 77 80 80 79 81 82 79 81 82 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 EFF (%)7 ISOLATION (VDC) Note: Other input to output voltages may be available. Please contact factory. 6 7 NOMINAL INPUT VOLTAGE. NOMINAL INPUT VOLTAGE,FULL LOAD. www.Power-Systems.de Page: 3 / 6 Version: 4-Oct-02 DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) SIMPLIFIED SCHEMATIC SINGLE OUTPUT +Vin +Vout +Vin DUAL OUTPUT +Vout Common -Vout -Vin PWM CONTROLLER ISOLATION REFERENCE & ERROR AMP -Vout -Vin PWM CONTROLLER ISOLATION REFERENCE & ERROR AMP MECHANICAL DIMENSIONS PIN 1 2 3 4 5 SINGLE +Vin -Vin +Vout NO PIN -Vout DUAL +Vin -Vin +Vout Common -Vout RECOMMENDED FOOTPRINT DETAILS www.Power-Systems.de Page: 4 / 6 Version: 4-Oct-02 DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) TYPICAL APPLICATIONS SINGLE OUTPUT INPUT +Vin +Vout DUAL OUTPUT INPUT +Vin +Vout OUTPUT OUTPUT LOAD1 DC-DC CONVERTER -Vin -Vout LOAD DC-DC CONVERTER -Vin Common LOAD2 -Vout TEMPERATURE DERATING OUTPUT POWER(W) 15.0 12.0 9.0 6.0 3.0 0 .0 -25 0 25 50 70 90 SAFE OPERATING AREA TA(degree C) KW SERIES APPLICATION NOTES: EXTERNAL CAPACITANCE REQUIREMENTS: No external capacitance is required for operation of the KW series. To meet the reflected ripple requirements of the converter, an input impedance of less than 0.5 ohm from DC to 220KHz is required. External output capacitance is not required for operation, however it is recommended that 10uF tantalum and 0.1uF ceramic capacitance be selected for reduced system noise. Additional output capacitance may be added for increased filtering, but should not exceed 220uF. www.Power-Systems.de Page: 5 / 6 Version: 4-Oct-02 DC-DC Converter UNIT KW Series ( 15 W WIDE INPUT RANGE DC-DC CONVERTER ) Negative Outputs: A negative output voltage may be obtained by connecting the +OUT to circuit ground and connecting –OUT as the negative output. FOR MORE INFORMATION CALL: Power Systems – The Power Solution Ilsfeld-Auenstein ( Germany ) Dörnet 8 E-mail: Info@Power-Systems.de Tel: + 49 / 70 62 / 67 59 – 6 Fax: + 49 / 70 62 / 67 59 -80 Home Page: www.Power-Systems.de www.Power-Systems.de Page: 6 / 6 Version: 4-Oct-02