PS-DA0250-01

DC-AC INVERTER UNIT PS-DA0250-01(S) (4 W SINGLE OUTPUTS) DESCRIPTION : This low profile DC to AC Inverter is developed for single lamps. Please contact us for confirmation regarding compatibility with your display. APPLICABLE LCD: 6 to 12 inches single lamp type Lamp Voltage: 600 Vrms Lamp Current: 6.0 mArms Lamp Start Up Voltage: 1.500 Vrms (Vin : 5 Vdc) FEATURES : Wide Operating temperature range Ext. PWM-Dimming Remote ON/OFF RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : (4.5) (4) LxWxH (PRELIMINARY INFORMATION) -10°C ~ +60°C -30°C ~ +85°C 95 %RH max SM02B-BHSS (JST) 96 x 20 x 8,6 mm 95.5 max 82±0.2 CN2 20 max 12.8±0.2 CN1 1 1 1 2 1 2-φ2.2±0.1 3 Unit : mm Weight : 13.7g typ. 8,6 max 1.6 max Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0590 SM02(8.0)B-BHS-1-TB SM02B-BHSS-1-TB Note t=1.6m m Molex or equal JST or equal JST or equal Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 Symbols Vin GND Vrm t Vbr N.C. Ratings 4.75 ~ 5.25 Vdc 0 ~ 0.5 = OFF / 2.5 ~ Vin = ON ext. PWM (low-active) Output side CN2 SM02(8.0)B-BHS: Pin No. CN 2-1 CN 2-2 CN 2-3 Symbols Vhigh N.C. Vlow Ratings 600 Vrms (6.0 mArms) (GND) Output side CN2 SM02B-BHSS: Pin No. CN 2-1 CN 2-2 Symbols Vhigh GND Ratings 600 Vrm s (6.0 m Arm s ) - Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (1) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.2.4, 12th February 2010 All specifications are subject to change without notice. DC-AC INVERTER UNIT PS-DA0250-01(S) (4 W SINGLE OUTPUTS) ELECTRICAL CHARACTERISTICS : Conditions Vrmt Tu (°C) (V) 5±0.25 0 ~ +60 5±0.25 0 ~ +60 5±0.25 0 ~ +60 5±0.25 0 ~ +60 5±0.25 0 ~ +60 Specification Min. 5.3 35 1.600 Typ. 6.0 20 0.8 45 1.800 Max. 6.7 1.0 55 Unit m Arm s % Adc kHz Vrm s Note Dut y 100 % Dut y min (PRELIMINARY INFORMATION) Parameters Symbols Vin (V) 5±0.25 5±0.25 5 5±0.25 5±0.25 Output Current Input Current Frequency Open Circuit Voltage Iout Iin F Vopen Note 1 : Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Remote ON/OFF (CN1-3) has priority and can not be used in combination with External PWM Dimming (CN1-4). When 'Ext.PWM' (CN1-4) is used 'Vrmt' (CN1-3) should not be connected. The inverter is optimized for external PWM Signal of 250 Hz (TTL High Active). The frequency could be 100 Hz ~ 2 kHz. Please take care about the vertical frequency harmonics. Note 2 : Note 3 : TEST CIRCUIT : SM02(8.0)B-BHS-1-TB: SW 1 a b Operation of unit Operation Non operation SM02B-BHS-1-TB: Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (2) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.2.4, 12th February 2010 All specifications are subject to change without notice.