PS-LD0101-1-080

LED-CONVERTER UNIT PS-LD0101-x-yyy(S) (9 W) DESCRIPTION : This low profile LED-Converter is developed for max. 1 LED-line APPLICABLE: 1 LED line Pout LED Voltage Lamp Current Input Voltage FEATURES : Independent Open LED Detection Voltage or Ext. PWM Dimming 1000:1 dimming ratio with external PWM Remote ON / OFF Wide Input Voltage Range RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity (PRELIMINARY INFORMATION) max. 9 Watt max. 35V max. 300 mAdc 10.8 ~ 13.2 Vdc Connector style -20°C ~ +70°C -20°C ~ +85°C 95 %RH max DIMENSIONS : LxWxH 64 x 32 x 10.5 mm Weight :5 (g) typ. Tolerance: ±0.3mm Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0890 53261-0590 Note t=1.0m m Molex Molex Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (1) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.387, 21st May 2010 All specifications are subject to change without notice. LED-CONVERTER UNIT PS-LD0101-x-yyy(S) (9 W) (PRELIMINARY INFORMATION) Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 CN 1-8 Symbols Ratings Vin 10.8 ~ 13.2 Vdc Vin 10.8 ~ 13.2 Vdc Vrm t 0 ~ 0.8 = OFF / 2.5 ~ 5.0 = ON Ext. PWM 0 ~ 0.5 = LOW / 2.5 ~ 5 = HIGH Vbr 0.0 ~ 5.0 (5V=low brightnes s ) GND GND GND - Output side CN2 Pin No. CN 2-1 CN 2-2 CN 2-3 CN 2-4 CN 2-5 Symbols Ratings RTN1 (-) LED STRING 1 RETURN RTN1 (-) LED STRING 1 RETURN NC Vhigh (+) 35 Vdc Vhigh (+) 35 Vdc Output Current Select Control Jumper Break Break Break Break Break JP 1 JP 2 JP 3 JP 4 JP 5 Output Current +10 mA +20 mA +40 mA +80 mA +120 mA Example: 30mA (Output Current Min.) + 10mA (JP1) = 40mA 30mA (Output Current Min.) + 80mA (JP4) = 110mA JP1 ~ JP5 OPEN = 300mA For more information, please visit our web-site. ELECTRICAL CHARACTERISTICS : Conditions Parameters Output Current Output Current Input Current Open Load Shutdow n Output Pow er Symbols Iout Im in Iin Vbias Pout Vin (V) 10.8 10.8 10.8 10.8 10.8 ~ 13.2 ~ 13.2 ~ 13.2 ~ 13.2 ~ 13.2 Vbr (V) 0 5 0 0 0 Tu (°C) -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 Min. TBD 0.03 TBD Specification Typ. 30 25 35 9 Max. TBD 0.5 TBD Unit m Adc % Adc Vdc Watt Note Dut y 100 % d ut y cycle Note 1 : Note 2 : Note 3: Note 4 : Note 5 : Do not use analog dimming function and external PWM for dimming at the same time. Pin terminal style converters have Molex connectors mounted. Above output current is the default value. Correct output current is to be selected by user and under his sole responsibility. Exceeding currents will damage the LED backlight. External PWM-signal is LOW active. If using external PWM for dimming, please connect Pin CN1-5 to GND. Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (2) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.387, 21st May 2010 All specifications are subject to change without notice. LED-CONVERTER UNIT PS-LD0101-x-yyy(S) (9 W) (PRELIMINARY INFORMATION) TEST CIRCUIT : ORDER KEY : PS-LD0101-x-yyy With order of this converter please give the following key: -x to be replaced by: -1 for connectors -2 for Pin-Terminal in case of quantity orders (300+ pcs), the proper current selection can be ordered: -yyy to be replaced by: three digit value for output current per LED line (from 030 to 300 including) Attention: * if no value is mentioned, 30 mA output current per LED line will be set as default * a selection of incorrect LED current may decrease lifetime or destroy the backlight * orders for preconfigured converters can’t be cancelled Examples: PS-LD0101-1-040 (S) 40 mA output current PCB with connectors PS-LD0101-2-150 (S) 150 mA output current PCB with Pin-Terminal CABLES : for input: 500 mm, stripped and tinned ends, order key for output: 500 mm, stripped and tinned ends, order key Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (3) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.387, 21st May 2010 All specifications are subject to change without notice.