OBN01316

MEDICAL & MILITARY Medline 200 Series 1 5 0 - 2 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Features • Low safety ground leakage current • Wide input range 90 to 260Vac • Input surge current protection • Overvoltage protection • Overcurrent protection • Power fail detection (PFD) signal • Optional cover and fan assembly • 100% burn-in at full rated load • Remote inhibit - TTL high disables output • Short curcuit protection Specifications INPUT Voltage range Frequency Input Current Leakage current Inrush Current Isolation 90-260VAC 47-63Hz. 3.2A (rms) at 115VAC 1.6A (rms) at 230VAC 90µA max at 115VAC, 60Hz 150A max at 230VAC, 50Hz 20A @ 115V or 40A at 230V at 25°C and cold start Input – Output: 4000VAC Input – Ground: 1500VAC Output – Ground: 500VAC PFD signal TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation 70% min on all models 20ms min at 110VAC ± 0.5% max at full load Efficiency Hold up time Line regulation ENVIRONMENTAL Operating Temperature Storage temperature Humidity Derating Cooling 0°C to 70°C –40°C to +85°C 5% to 95% non-condensing Derate from 100% at +50°C linearly to 50% at +70°C. 25CFM forced air, provided on “C” version, to be provided for “B” version by user OUTPUT Power Voltage Current Ripple & Noise Overvoltage protection Overcurrent Protection Temperature coefficient Transient response 200W See table See table 2% p-p max Provided on output #1 only, set at 112-132% of it nominal output voltage The output protected to short circuit conditions 0.04%°C all outputs Max excursion of 4% or better on all models, recovering to 1% of final value within 500us after a 25% step load change GENERAL Switching frequency MTBF 88-112kHz. 350,000 hours at full load 25°C ambient , calculated per MIL-HDBK-217F STANDARDS AND APPROVALS Safety standards C-Tick EMC standards IEC60601-1 TUV EN60601-1, EN60601-1 AS/NZS CISPR11 Group 1, Class A EN55011 Class B, FCC Class B,VCII, EN61000-3-2, -3, EN60001-4-2, -3, -4, -5, -6, -8, -11 Technical Illustration MECHANICAL Dimensions Weight See drawing 0.82kg for “B” version 0.96kg for version “C” version Notes: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector P1 is Dinkle DT-35-B01W-09 screws are M3, nickle plated 4. Connector P3 mates with Molex housing 22-01-1043 and Molex 40445 series crimp terminal 5. Connector P4/P5 mates with Molex housing 22-01-1023 and Molex 40445 series crimp terminal 6. P4 is for DC fan rated 24V/0.2A (models PM201/27), or 5V/0.38A (models PM201-40-3), and 12V/0.2A (other models, Pin1 +V and Pin2 COM 7. Weight: 0.82 Kgs (1.83 Lbs) approx for “B” version 0.96 Kgs (2.14 Lbs) approx for “C” version Your dependable power partner – www.powerbox.com.au 345 MEDICAL & MILITARY Medline 200 Series 1 5 0 - 2 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Selection Table MAX. MODEL NUMBER VNOM OUTPUT #1 IMIN IMAX TOL OUTPUT #2 VNOM IMIN IMAX TOL OUTPUT #3 VNOM IMIN IMAX TOL VNOM OUTPUT #4 IMIN IMAX TOL OUTPUT POWER OBN01016 OBN01013 OBN01037 OBN01046 OBN01055 OBN01070 OBN01204 OBN01207 OBN01210 OBN012A5 OBN01310 OBN01313 OBN01316 OBN01315 OBN01319 OBN01404 OBN01403 OBN01407 OBN01410 OBN01420 OBN01413 5.1V 3.3V 12V 15V 24V 30V 48V +5.1V +5.1V +5.1V +12V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +3.3V 0A 0A 0A 0A 0A 0A 0A 3.0A 3.0A 3.0A 1.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 35A 46A 16.7A 13.4A 8.4A 6.7A 4.2A 30A 30A 30A 8A 30A 30A 30A 30A 30A 30A 30A 30A 30A 30A 2% 3% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 3% +12V +15V +24V +24V +12V +12V +15V +15V +12V +12V +15V +12V +12V +5.1V 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 8A 6A 4A 4A 8A 8A 6A 6A 8A 8A 6A 8A 8A 8A 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% -5V -12V -15V -12V -24V -12V -15V -12V -15V -12V 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 6A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 5V 24V 12V 15V 12V 0A 0A 0A 0A 0A 6A 4A 4A 4A 4A 4% 4% 4% 4% 4% 175W 150W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 200W 175W NOTES: (1) Add suffix “B” for U-bracket format and “C” for enclosed format. (2) Peak current is 12A on +12V, 9A on +15V and 6A on +24V. (3) Output #4 is floating. It can be connected externally for positive or negative output. (4) 200 watts for “C” version with a cover and fan assembly 100 watts for “B” version without moving air (maximum current of ouput #1 & #2 derated to 50%), or 200 watts with 25 CFM forced air provided by user. (5) When the remote Sense facility is not used, +Sense must be connected to +V, and -Sense to Return, on P2 connector. (6) All models may be operated at no-load. At no-load, output voltage tolerance increases to 10%. Pin Chart CONNECTOR MODEL/PIN OBN01016 OBN01031 OBN01046 OBN01070 OBN01204 OBN01210 OBN01310 OBN01316 OBN01319 OBN01013 OBN0PM201-13 OBN01055 OBN01207 OBN01313 OBN01315 P1 1 -Sense P2 2 RET. P3 4 RET P4 5 RET 3 RET. 6 7 8 9 1 2 3 4 1 2 Output Output Output +Sense FAN #1 #1 #1 RET Output #2 N.C. N.C. N.C. N.C. N.C. FAN FAN FAN COM COM. PFD INHIBIT+ INHIBITRET. COM COM RET. RET. COM COM RET. RET. COM COM RET. RET. COM COM RET. RET. PFD INHIBIT+ INHIBITPFD INHIBIT+ INHIBITPFD INHIBIT+ INHIBIT- Output #1 Output #1 Output COM #1 RET. Output COM #1 RET. COM RET. COM RET. COM RET. COM RET. COM RET. COM RET. COM RET. COM RET. Output Output #2 #3 Output #2 N.C. Output #1 Output COM #1 RET. OBN01403 OBN01410 OBN14113 COM RET. Output Output #3 #3 RETURN OBN01404 OBN01407 OBN01420 Output #1 Output #1 Output Output Output Output #2 #2 #3 #4 RETURN FAN PFD INHIBIT+ INHIBIT- 346