PD65-30

OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Features • • • • • • Low cost 100% burn-in Small size, light weight Overvoltage protection Overcurrent protection Three wide input ranges: 10–30VDC, 20–60VDC, 30–90VDC Specifications INPUT Input voltage 10–30VDC (PD40 & 65 – L series) 20–60VDC (PD40 & 65 – M series) 30–90VDC (PD40 & 65 – H series) 10–20VDC (PD110 – L series) 18–36VDC (PD110 – M series) 36–72VDC (PD110 – H series) 4.1A (rms) for 24VDC typical for PD65 2.1A (rms) for 48VDC typical for PD65 1.5A (rms) for 72VDC typical for PD65 OPERATING MTBF Switching frequency Efficiency Line regulation Withstand voltage 100,000 hours minimum at full load at 25°C ambient 32kHz ±5kHz 70% minimum at full load ±0.5% maximum at full load 1000VDC from input to output Input current ENVIRONMENTAL Operating temperature Derating 0°C to +70°C Derate from 100% at +50°C linearly to 50% at +70°C -40°C to +85°C 5%–95% non-condensing OUTPUT Output voltage/current Total output power Ripple & noise Overvoltage protection Overcurrent protection Temperature coefficient Transient response See rating chart 40W, 65W and 110W 1% pk-pk max. Set at 112–132% of its nominal output voltage All outputs protected to short circuit conditions All outputs ±0.04% per °C maximum Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500µs after a 25% step load change See notes Storage temperature Relative humidity STANDARDS AND APPROVALS C-tick AS/NZCISPR11 Group 1, Class A Output derating 122 OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD40 SERIES (40W) MAXIMUM OUTPUT POWER 40W 40W 40W 40W +12V +15V +24V +12V +12V +15V +15V +24V 0.2A 0.2A 0.1A 0.2A 0.2A 0.2A 0.2A 0.1A 2A 2A 1A 2A 2A 2A 2A 1A 5% 5% 5% 5% 5% 5% 5% 5% -5V -12V -15V -12V -12V 0A 0A 0A 0A 0A 0.8A 0.8A 0.8A 0.8A 0.8A 5% 5% 5% 5% 5% 40W 40W 40W 40W 40W 40W 40W 40W OUTPUT #1 MODEL NUMBER VNOM. IMIN. IMAX. PD40-10 PD40-12 PD40-13 PD40-14 PD40-23 PD40-24 PD40-25 PD40-30 PD40-31 PD40-32 PD40-33 PD40-39 5V 12V 15V 24V +5V +5V +5V +5V +5V +5V +5V +5V 0A 0A 0A 0A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A 8.0A 3.5A 3.0A 2.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A 3.0A OUTPUT #2 TOL. VNOM. IMIN. 2% 1% 1% 1% 3% 3% 3% 3% 3% 3% 3% 3% OUTPUT #3 TOL. VNOM. IMIN. IMAX. TOL. IMAX. NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10% 2. Suffix codes for mechanical format and input range are as follows. PD40-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B=L-bracket, C=enclosed), eg, PD40-31MC (20–60VDC input range, enclosed). 3. “L” series is suitable only for 75% of the above stated maximum output power. Technical Illustration PD40 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3041 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3061 and Molex 2878 series crimp terminal 5. Weight: 300 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin Chart MODEL PD40-10 PD40-13 PD40-23 PD40-25 PD40-30 PD40-32 PD40-39 PD40-31 PD40-33 PD40-12 PD40-14 PD40-24 PIN 1 OUTPUT #1 OUTPUT #2 OUTPUT #2 PIN 2 OUTPUT #1 OUTPUT #1 OUTPUT #1 PIN 3 OUTPUT #1 OUTPUT #1 OUTPUT #1 PIN 4 RETURN COMMON RETURN COMMON RETURN PIN 5 RETURN COMMON RETURN COMMON RETURN PIN 6 RETURN N/C OUTPUT #3 Your dependable power partner – www.powerbox.com.au 123 OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD65 SERIES (65W) MAXIMUM OUTPUT POWER MODEL NUMBER OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. PD65-10 PD65-12 PD65-13 PD65-14 PD65-23 PD65-24 PD65-25 PD65-30 PD65-31 PD65-32 PD65-33 PD65-39 PD65-40 5V 12V 15V 24V +5V +5V +5V +5V +5V +5V +5V +5V +5V 0A 0A 0A 0A 1A 1A 1A 1A 1A 1A 1A 1A 1A 10A 5.5A 4.5A 3.0A 6.0A 6.0A 6.0A 6.0A 6.0A 6.0A 6.0A 6.0A 6.0A 1% 1% 1% 1% 3% 3% 3% 3% 3% 3% 3% 3% 3% +12V +15V +24V +12V +12V +15V +15V +24V +12V 0.5A 0.4A 0.3a 0.5A 0.5A 0.4A 0.4A 0.3A 0.5A 3A 3A 2a 3A 3A 3A 3A 2A 3A 5% 5% 5% 5% 5% 5% 5% 5% 5% -5V -12V -15V -12V -12V -12V 0.1A 0.1A 0.1A 0.1A 0.1A 0.1A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A 10% 10% 10% 10% 10% 10% -5V 0.1A 0.5A 10% 50W 65W 65W 65W 65W 65W 65W 65W 65W 65W 65W 65W 65W NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10%. 2. Suffix codes for mechanical format and input range are as follows: PD65-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed), eg, PD65-31MC (20–60VDC input range, enclosed). 3. The models for 10–30VDC input range are suitable only for 70% of the above stated maximum output power. Technical Illustration PD65 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3031 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3081 and Molex 2878 series crimp terminal 5. Weight: 380 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin chart MODEL PD65-10 PD65-13 PD65-23 PD65-25 PD65-30 PD65-32 PD65-39 PD65-40 124 PD65-31 PD65-33 PD65-12 PD65-14 PD65-24 PIN 1 OUTPUT #1 OUTPUT #1 OUTPUT #1 OUTPUT #1 PIN 2 OUTPUT #1 OUTPUT #1 OUTPUT #1 OUTPUT #1 PIN 3 OUTPUT #1 COMMON RETURN COMMON RETURN OUTPUT RETURN PIN 4 OUTPUT #1 COMMON RETURN COMMON RETURN COMMON RETURN PIN 5 RETURN OUTPUT #2 OUTPUT #2 COMMON #2 PIN 6 RETURN OUTPUT #2 OUTPUT #2 OUTPUT #2 PIN 7 RETURN N/C OUTPUT #3 OUTPUT #3 PIN 8 RETURN N/C N/C OUTPUT #4 OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD110 SERIES (110W) MAXIMUM OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 MODEL OUTPUT NUMBER VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. IPEAK TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. POWER PD110-10 PD110-12 PD110-13 PD110-14 PD110-16 PD110-23 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 5V 12V 15V 24V 30V +5V +5V +5V +5V +5V +5V +5V +5V +5V 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 22A 9.0A 7.5A 4.5A 3.6A 10A 10A 10A 10A 10A 10A 10A 10A 10A 3% 2% 2% 2% 2% 3% 3% 3% 3% 3% 3% 3% 3% 3% +12V +12V +15V +12V +15V +12V +12V +24V +15V 0A 0A 0A 0A 0A 0A 0A 0A 0A 5A 5A 4A 5A 4A 5A 5A 3A 4A 9.0A 9.0A 7.5A 9.0A 7.5A 9.0A 9.0A 5.0A 7.5A 3% 3% 3% 3% 3% 3% 3% 3% 3% -12V -15V -12V -15V -12V -12V -12V -15V 0A 0A 0A 0A 0A 0A 0A 0A 1A 1A 1A 1A 1A 1A 1A 1A 4% 4% 4% 4% 4% 4% 4% 4% -5V +24V +12V +24V +12V -5V 0A 0A 0A 0A 0A 0A 1A 1A 1A 1.5A 1A 1A 4% 4% 4% 10% 4% 4% 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W NOTES 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. 2. PD110 “M” & “H” series are suitable only for 110W maximum at 20 CFM forced air cooling or 80W maximum at convection cooling. PD110 “L” series are suitable only for 90W maximum at 20 CFM forced air cooling or 70W maximum at convection cooling. 3. Suffix codes for input range, mechanical format and connector are as follows: PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L = 10–20VDC, M = 18–36VDC, H = 36–72VDC), “X4” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed) and “X5” is the input and output connector code (Blank + Molex KK type, T = miniature terminal block), eg, PD110–31MCT (18–36VDC input range, enclosed format and miniature terminals blocks). Technical Illustration PD110 Enclosed NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal 4. Miniature terminal blocks: Input terminals allow wires up to 2mm2 (AWG #14) Output terminals allow wires up to 2mm2 (AWG #14) 5. Weight: 640 grams (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin chart MINI TERMINAL MOLEX CONNECTOR MODEL PD110-10 PD110-13 PD110-16 PD110-23 PD110-31 PD110-12 PD110-14 1 1,2,3 OUTPUT #1 OUTPUT #1 OUTPUT #1 OUTPUT #1 2 4,5 RETURN 3 6,7 RETURN 4 8,9 OUTPUT #1 OUTPUT #2 OUTPUT #2 OUTPUT #2 10 N/C 5 11 N/C 12 KEY 6 13 N/C PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN N/C N/C N/C N/C OUTPUT #3 OUTPUT #3 N/C KEY KEY KEY N/C OUTPUT Your dependable power partner – www.powerbox.com.au 125