CM200DY-24H

CM200DY-24H Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Dual IGBTMOD™ H-Series Module 200 Amperes/1200 Volts A B F F G P C2E1 E2 C1 G2 E2 C D G1 E1 J P K N - DIA. (4 TYP.) M M Q - M6 THD (3 TYP.) R .110 TAB L E H M Description: Powerex IGBTMOD™ Modules are designed for use in switching applications. Each module consists of two IGBT Transistors in a half-bridge configuration with each transistor having a reverseconnected super-fast recovery free-wheel diode. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management. G2 E2 C2E1 E2 C1 E1 G1 Features: □ Low Drive Power □ Low VCE(sat) □ Discrete Super-Fast Recovery (135ns) Free-Wheel Diode □ High Frequency Operation (20-25kHz) □ Isolated Baseplate for Easy Heat Sinking Applications: □ AC Motor Control □ Motion/Servo Control □ UPS □ Welding Power Supplies □ Laser Power Supplies Ordering Information: Example: Select the complete part module number you desire from the table below -i.e. CM200DY-24H is a 1200V (VCES), 200 Ampere Dual IGBTMOD™ Power Module. Type CM Current Rating Amperes 200 VCES Volts (x 50) 24 Outline Drawing and Circuit Diagram Dimensions A B C D E F G H Inches 4.25 3.66± 0.01 2.44 1.89± 0.01 1.22 Max. 0.98 0.85 0.60 Millimeters 108.0 93.0± 0.25 62.0 48.0± 0.25 31.0 Max. 25.0 21.5 15.2 Dimensions J K L M N P Q R Inches 0.59 0.55 0.30 0.28 0.256 Dia. 0.24 M6 Metric 0.20 Millimeters 15.0 14.0 8.5 7.0 Dia. 6.5 6.0 M6 5.0 269 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM200DY-24H Dual IGBTMOD™ H-Series Module 200 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Junction Temperature Storage Temperature Collector-Emitter Voltage (G-E SHORT) Gate-Emitter Voltage Collector Current Peak Collector Current Diode Forward Current Diode Forward Surge Current Power Dissipation Max. Mounting Torque M6 Terminal Screws Max. Mounting Torque M6 Mounting Screws Module Weight (Typical) V Isolation * Pulse width and repetition rate should be such that device junction temperature does not exceed the device rating. Symbol Tj Tstg VCES VGES IC ICM IF IFM Pd – – – VRMS CM200DY-24H –40 to 150 –40 to 125 1200 ± 20 200 400* 200 400* 1500 26 26 400 2500 Units °C °C Volts Volts Amperes Amperes Amperes Amperes Watts in-lb in-lb Grams Volts Static Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Collector-Cutoff Current Gate Leakage Current Gate-Emitter Threshold Voltage Collector-Emitter Saturation Voltage Symbol ICES IGES VGE(th) VCE(sat) QG VFM Test Conditions VCE = VCES, VGE = 0V VGE = VGES, VCE = 0V IC = 20mA, VCE = 10V IC = 200A, VGE = 15V IC = 200A, VGE = 15V, Tj = 150°C Total Gate Charge Diode Forward Voltage VCC = 600V, IC = 200A, VGS = 15V IE = 200A, VGS = 0V Min. – – 4.5 – – – – Typ. – – 6.0 2.5 2.25 1000 – Max. 1.0 0.5 7.5 3.4** – – 3.5 Units mA µA Volts Volts Volts nC Volts ** Pulse width and repetition rate should be such that device junction temperature rise is negligible. Dynamic Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Input Capacitance Output Capacitance Reverse Transfer Capacitance Resistive Load Switching Times Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Symbol Cies Coes Cres td(on) tr td(off) tf trr Qrr IE = 200A, diE/dt = –400A/µs IE = 200A, diE/dt = –400A/µs VCC = 600V, IC = 200A, VGE1 = VGE2 = 15V, RG = 1.6Ω VGE = 0V, VCE = 10V, f = 1MHz Test Conditions Min. – – – – – – – – – Typ. – – – – – – – – 1.49 Max. 40 14 8 250 400 300 350 250 – Units nF nF nF ns ns ns ns ns Diode Reverse Recovery Time Diode Reverse Recovery Charge µC Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Thermal Resistance, Junction to Case Thermal Resistance, Junction to Case Contact Thermal Resistance Symbol Rth(j-c) Rth(j-c) Rth(c-f) Test Conditions Per IGBT Per FWDi Per Module, Thermal Grease Applied Min. – – – Typ. – – – Max. 0.085 0.18 0.045 Units °C/W °C/W °C/W 270 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM200DY-24H Dual IGBTMOD™ H-Series Module 200 Amperes/1200 Volts OUTPUT CHARACTERISTICS (TYPICAL) TRANSFER CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 400 COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) 400 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) Tj = 25oC 15 5 VCE = 10V Tj = 25°C Tj = 125°C VGE = 15V Tj = 25°C Tj = 125°C 12 320 VGE = 20V 11 320 4 240 10 240 3 160 160 2 80 7 9 8 80 1 0 0 2 4 6 8 10 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 0 0 80 160 240 320 400 COLLECTOR-CURRENT, IC, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE VS. VCE (TYPICAL) 10 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 103 Tj = 25°C Tj = 25°C IC = 400A EMITTER CURRENT, IE, (AMPERES) CAPACITANCE, Cies, Coes, Cres, (nF) 102 Cies 8 101 Coes 6 IC = 200A 102 4 100 Cres VGE = 0V f = 1MHz 2 IC = 80A 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 101 0 0.8 1.6 2.4 3.2 4.0 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) 10-1 10-1 100 101 102 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CURRENT, Irr, (AMPERES) GATE CHARGE, VGE 103 REVERSE RECOVERY TIME, t rr, (ns) 103 tf td(off) 102 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) IC = 200A 16 SWITCHING TIME, (ns) VCC = 400V VCC = 600V td(on) Irr 102 102 t rr 12 101 8 tr VCC = 600V VGE = ±15V RG = 1.6Ω Tj = 125°C di/dt = -400A/µsec Tj = 25°C 4 101 101 102 COLLECTOR CURRENT, IC, (AMPERES) 103 101 101 102 EMITTER CURRENT, IE, (AMPERES) 100 103 0 0 400 800 1200 1600 GATE CHARGE, QG, (nC) 271 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM200DY-24H Dual IGBTMOD™ H-Series Module 200 Amperes/1200 Volts NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.085°C/W NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 10-2 10-1 100 101 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 10-2 10-1 100 101 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.18°C/W 10-1 10-1 10-1 10-1 10-2 10-2 10-2 10-2 10-3 10-5 TIME, (s) 10-4 10-3 10-3 10-3 10-5 TIME, (s) 10-4 10-3 10-3 272