VLA513-01

VLA513-01 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 A Hybrid IC IGBT Gate Driver C B L J K G E D H 1 D F 8 6 VCC 2 INTERFACE 1 7 VO 8 VEE 180Ω OPTO COUPLER 5 PIN: NC Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L Rev. 04/07 Inches 1.85 Max. 1.063 Max. 0.28 Max. 0.59 Max. 0.10 0.216 Max. 0.08 Max. 0.70 0.18±0.06 0.03 0.02 Millimeters 47.0 Max. 27.0 Max. 7.0 Max. 15.0 Max. 2.54 5.5 Max. 2.0 Max. 17.78 4.5±1.5 0.75 0.5 Description: VLA513-01 is a hybrid integrated circuit designed for driving IGBT modules. This device operates as an isolation amplifier for these modules and provides the required electrical isolation between the input and output with an optocoupler. Features: £ Propagation Delay time: 0.2 µs (Typical) £ Output is ±5A maximum £ Two Supply Drive (VCC: 15 Volts, VEE: -10 Volts) £ SIP Outline Allows More Space on Mounting Area £ Electrical Isolation Voltage Between Input and Output (2500 Vrms for 1 Minute) £ TTL Compatible Input Application: To drive IGBT modules for welding, induction heating, or inverters. Recommended IGBT Modules: NFH Series IGBTs – VCES = 600V & 1200V up to 200A class (f: up to 60kHz), 400A class (f: up to 30kHz) NF Series IGBTs – VCES = 600V up to 600A VCES = 1200V up to 400A  Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 VLA513-01 Hybrid IC IGBT Gate Driver Absolute Maximum Ratings, Ta = 25°C unless otherwise specified Characteristics Symbol VLA513-01 Units Supply Voltage, DC VCC 18 Volts VEE -12 Volts VI -1 ~ 7 Volts VO VCC Volts IOHP -5 Amperes Input Signal Voltage (Applied between Pin 1 - 2, 50% Duty Cycle, Pulse Width 1ms) Output Voltage (When the Output Voltage is "H") Output Current (Pulse Width 2µs, f ≤ 20kHz) IOLP 5 Amperes Isolation Voltage (Sine Wave Voltage 60HZ, for 1 Minute) VISO 2500 Vrms Case Temperature1 (Surface Temperature Opto-coupler Location)*** TC1 85 °C Operating Temperature (No Condensation Allowable) Topr -20 to 70 °C Storage Temperature (No Condensation Allowable) Tstg -25 to 100* °C *Differs from temperature cycle condition. Electrical and Mechanical Characteristics, Ta = 25°C unless otherwise specified, VCC = 15V, VEE = -10V Characteristics Symbol Supply Voltage VCC Recommended Range Min. Typ. Max. Units 14 15 — Volts VEE Pull-up Voltage on Input Side VIN Recommended Range -5 -8 -12 Volts Recommended Range 4.75 5 5.25 Volts "H" Input Current IIH Recommended Range 9.5 10.0 14.0 mA f Recommended Range — — 60 kHz Gate Resistance RG Recommended Range "H" Input Current IIH Switching Frequency VIN = 5V — — W 10 — mA VOH — 13 14 — Volts "L" Output Voltage VOL — -8 -9 — Volts "L-H" Propagation Time tPLH IIH = 16mA 0.1 0.2 0.5 µs tr IIH = 16mA — 0.3 1 µs tPHL IIH = 16mA 0.05 0.2 0.5 µs tf IIH = 16mA — 0.3 1 µs "H-L" Propagation Time "H-L" Fall Time 2 — "H" Output Voltage "L-H" Rise Time  Test Conditions Rev. 04/07 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 VLA513-01 Hybrid IC IGBT Gate Driver 0.5 PROPAGATION DELAY TIME “L-H”, tPLH, (µs) PROPAGATION DELAY TIME “H-L”, tPHL, (µs) PROPAGATION DELAY TIME “L-H”, tPLH, (µs) PROPAGATION DELAY TIME “H-L”, tPHL, (µs) VCC = 15V VEE = -10V RG = 3W VIN = 5V Load: CM400DU-24NFH 0.6 0.4 0.3 tPLH 0.2 tPHL 0.1 0 0 20 40 60 tPLH, tPHL VS. VI CHARACTERISTICS (TYPICAL) 0.7 80 VCC = 15V VEE = -10V RG = 3W Ta = 25°C Load: CM400DU-24NFH 0.6 0.5 0.4 0.3 tPLH 0.2 tPHL 0.1 0 3 AMBIENT TEMPERATURE, Ta, (°C) 18 5 6 7 INPUT SIGNAL VOLTAGE, VI, (VOLTS) RG = 2W OR MORE* 4 3 2 1 0 0 20 40 60 80 100 AMBIENT TEMPERATURE, Ta, (°C) ICC VS. (VCC + |VEE|) CHARACTERISTICS (TYPICAL) * The following numberical expression must be satisfied PT > (VCC + IVEEI) * {(Q1 + IQ2I) * f + ICC} Q1: Gate Charge on plus bias Q2: Gate Charge on minus bias f: Switching frequency ICC: Constant dissipation current of driver Ta = 25°C DISSIPATION CURRENT, ICC, (mA) 4 PT VS. Ta (MAXIMUM RATING) 5 TOTAL POWER DISSIPATION, PT, (WATTS) tPLH, tPHL VS. Ta CHARACTERISTICS (TYPICAL) 0.7 15 12 Refer to “ICC VS. (VCC + IVEEI) Characteristics” 9 6 3 0 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE, (VCC + IVEEI), (VOLTS) Application Circuit Switching Time Definitions SWITCHING TIME DEFINITIONS VI VLA513-01 VIN 5V 1 2 5 6 7 VO 8 + tr tf 90% CM200DU-24NFH 220µF RG + 220µF VCC VCC = 15V VEE = -10V RG = 3Ω 50% 10% VEE Notes: tPLH tPHL (1) Power supply decoupling capacitors should be connected as close as possible to the pins of the gate driver. (2) Power supply decoupling capacitors should be good quality, low ESR types. (3) Printed circuit layout should minimize wiring lengths and utilize shielding layers to suppress noise. Rev. 04/07