VLA606-01R

VLA606-01R IPM Drive Interface Module Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 A B 40 32 22 D 15 8 1 D C + VIN = 24V – VLA106 VLA106 VLA106 VLA106 -24151 -24151 -24151 -24154 + 1 VLA606-01R + + + IPM VUPC 2 UFO 3 UP 4 VUP1 8 VVPC 9 VFO 10 VP 11 VVP1 15 VWPC 16 WFO 17 WP 18 VWP1 22 VNC 23 VN1 24 UN 25 VN 26 WN 27 FO 33 UP 34 VP 35 WP 36 UN 37 VN 38 WN 39 FO CONTROLLER 32 5V E E F Description: VLA606-01R is an interface module for IPM drive. Features: £ Contains 6 Opto-couplers for IPM Drive and 4 Opto-couplers for Fault Signal for 3-Phase Inverter £ Reverse Input Voltage Protection £ SIP Saves More Space on Mother Board £ Pin Arrangement Matches IPM's Pin Arrangement £ Electrical Isolation Voltage Between Input and Output (2500 Vrms for 1 Minute) Application: To drive IPMs Recommended IPM Modules: PM Series Modules 40 Outline Drawing and Circuit Diagram Dimensions A B C D E F Inches 3.38 1.22 3.07 0.16 0.26 0.47 Millimeters 86.0 31.0 78.0 4.0 6.5 12.0 Note: All dimensions listed are maximums except C. Rev. 4/12  Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 VLA606-01R IPM Drive Interface Module Absolute Maximum Ratings, Ta = 25°C unless otherwise specified Characteristics Symbol VLA606-01R Units Supply Voltage1 (Between Pins 4-1, 11-8, 18-15, 23-22) VCC1 -0.5 ~ 20 Volts Supply Voltage 2 (Between Pins 39-40) VCC2 -6 ~ 40 Volts IF1 20 mA Input Current 1 (Between Pins 32-33, 32-34, 32-35, 32-36, 32-37, 32-38) Input Current 2 (Between Pins 4-2, 11-9, 18-16, 23-27) IF2 20 mA Operating Temperature (No Condensation Allowable) Topr -20 to 70 °C Storage Temperature (No Condensation Allowable) Tstg -25 to 100 °C Input-Output Isolation Voltage (Primary – Secondary AC, 1 Min.) Viso 2500 Vrms Electrical and Mechanical Characteristics, Ta = 25°C unless otherwise specified Characteristics Symbol Output Low Voltage 1 VOL1 — tON TBD Refer to TBD TBD TBD µs — — 0.4 Volts Turn-on Time 1 Turn-off Time 1 tOFF Output Low Voltage 2 VOL2 Test Conditions Min. Test Conditions Typ. Max. Units — 0.5 Volts TBD TBD µs Turn-on Time 2 tON2 TBD TBD TBD µs Turn-off Time 2 tOFF1 TBD TBD TBD µs Test Conditions 32 VCC3 5V Vi VO7 VO1 VO2 33 3 34 10 35 17 36 24 37 25 VO3 VO4 VO5 26 VO6 VLA606-01R 38 VO7 VCC2 5V 4, 11, 18, 23 VCC1 VO1 ~ 6 2 39 9 1.9kΩ 15V 910Ω Vf 16 27 40 1, 8, 15, 22 Vf : VIN = 15V f = 100Hz D.F. = 50% Vi : VIN = 5V f = 1kHz D.F. = 50% Vi 5V Vf 15V 0V VO1 ~ 6 15V 0V VO7 5V 4.5V VOL2 1.5V ton1  1.5V 0.5V 0V toff1 VO1 ton2 0V toff2 Rev. 4/12