1SD312F2-CM900HB-90H 数据手册
1SD312F2
Data Sheet
1SD312F2-CM900HB-90H
Single-Channel SCALE Plug-and-Play IGBT
Driver
Ultra-compact, high-performance driver for 2-level, 3-level and
multilevel converters
Abstract
The SCALE plug-and-play driver 1SD312F2-CM900HB-90H is a compact
single-channel intelligent gate driver designed for Mitsubishi’s high-voltage
IGBTs of type CM900HB-90H. The driver features a fiber-optic interface and
a selectable operation mode via a jumper.
For drivers adapted to other types of high-power and high-voltage IGBT modules, refer
to www.IGBT-Driver.com/go/plug-and-play
Product Highlights
Plug-and-play solution
Protects the IGBT from short-circuit failure
Active clamping of V ce at turn-off
Extremely reliable; long service life
No electrolytic capacitors
Gate current up to 12A
Fiber-optic links
Monitoring of supply voltage and fiber optics
Switching frequency DC to max. 8kHz
Duty cycle 0... 100%
Suitable DC/DC power supply as separate unit
Shortens application development time
IGBT-Driver.com
Applications
Three/multi-level converters
Two-level converters
Medium-voltage converters
High-voltage applications
Industrial drives
Traction
Railroad power supplies
Wind-power converters
Radiology and laser technology
Research
Almost all other conceivable
applications
Page 1
1SD312F2
Data Sheet 1SD312F2-CM900HB-90H
Important Notes
This data sheet contains only product-specific data. For a detailed description, mustread application notes and common data that apply to the whole series, please refer to
the “Description and Application Manual for 1SD312F2 SCALE High-Voltage IGBT
Drivers”.
When applying SCALE plug-and-play drivers, please note that these drivers are
specifically adapted to a particular type of IGBT module. Therefore, the type
designation of SCALE plug-and-play drivers also includes the type designation of the
corresponding IGBT module. These drivers are not valid for IGBT modules other
than those specified. Incorrect use may result in failure.
Mechanical and Electrical Interfaces
Dimensions: 187 x 63 mm.
Mounting Principle: Direct screw mount on IGBT.
Interface
Remarks
Part type #
Drive signal input
Status output
Power supply connector
Fiber-optic receiver (Notes 14,16)
Fiber-optic transmitter (Notes 14,17)
On-board connector (Note 15)
HFBR-2522
HFBR-1522
77315-101-05
Power supply connector
Designator
Pin numbers
Ground
Supply voltage
V DC
GND (Note 19)
1, 2, 4, 5
3
Absolute Maximum Ratings
Parameter
Remarks
Supply voltage V DC
Gate peak current I out
Average supply current I DC
Output power gate driver
Switching frequency
DC-link voltage
Operating temperature
VDC to GND (Note 1)
Page 2
Note 8
Note 3
Notes 3,11
Note 11
Note 5
Note 11
Min Max
Units
0 17.3
-6 +12
250
3
8
3000
-40 +85
V
A
mA
W
kHz
V
°C
CT-Concept.com
1SD312F2
Data Sheet 1SD312F2-CM900HB-90H
Storage temperature
-40 +90
°C
Electrical Characteristics
All data refer to +25°C and V DC = 16.4V unless otherwise specified
Power supply
Remarks
Min Typ. Max
Units
Nominal supply voltage V DC
Supply current I DC
Turn-on threshold V th
Hysteresis on/off
VDC to GND (Note 1)
Without load (Note 2)
Note 4
Note 4
15.5 16.4 16.8
80
14
1.0
V
mA
V
V
Short-circuit protection
Remarks
Min Typ. Max
Units
V ce -monitoring threshold
Response time
Response time
Blocking time
Between aux. terminals
3-level mode (Notes 10,18)
2-level mode (Notes 6,18)
2-level mode (Note 7)
Timing characteristics
Remarks
Turn-on delay t pd(on)
Turn-off delay t pd(off)
Output rise time t r(out)
Output fall time t f(out)
Acknowledge delay time
Acknowledge pulse width
Note
Note
Note
Note
At status output (Note 13)
At status output
Gate output
Remarks
Turn-on gate resistor R g(on)
Turn-off gate resistor R g(off)
Note 8
Note 8
IGBT-Driver.com
680
10.8 11.5
11.6 12.4
1
V
μs
μs
s
Min Typ. Max
Units
430
520
100
100
450
ns
ns
ns
ns
ns
μs
12
12
9
9
0.7
1.8
Min Typ. Max
10
10
Units
Ω
Ω
Page 3
1SD312F2
Data Sheet 1SD312F2-CM900HB-90H
Footnotes to the key data
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
Supply voltages higher than those specified can lead to the destruction of the driver and protection
circuits on the output side. The gate-emitter voltage tracks the supply voltage. (Not regulated by
the gate drive unit.) The recommended DC/DC power supply ISO3116I with high-voltage insulation
capability is a suitable separate unit.
Static power consumption of the gate driver.
If the specified power consumption of the gate driver is exceeded on average, this indicates an
overload of the gate driver and the external DC/DC power supply ISO3116I.
Under-voltage monitoring of supply voltage of the gate driver. For a voltage lower than this limit,
the power modules are switched off.
This limit is due to active clamping. Refer to the “Description and Application Manual for 1SD312F2
SCALE High-Voltage IGBT Drivers”.
Pulse width of the direct output of the gate drive unit. (Excluding the delay of the gate resistors.)
Duration of blocking the command input (keeping the gate driver and the IGBT in the off-state)
after fault detection, i.e. power supply under-voltage lock out, or – only in 2-level mode – shortcircuit detection. (For three/multilevel mode, turn-off under the short-circuit condition is managed
by the host controller.)
The gate current is limited by on-board gate resistors.
Refers to the direct output of the gate drive unit. (Excluding the delay of the gate resistors.)
Including the delay of external fiber-optic links. Measured from the turn-on transition at direct
output of the gate drive unit (excluding the delay of the gate resistors) to the transition of the
status signal at the optical receiver on the host controller side.
Application-specific self-heating of gate drivers and IGBT modules, especially at high switching
frequency, must be taken into account. The switching frequency is usually limited due to the
switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be
incorporated in the user’s application, no binding recommended value for self-heating and thus for
the maximum useable output power can be given. It is therefore recommended to check the gate
driver’s ambient temperature within the system.
Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the direct output of the
gate drive unit. (Excluding the delay of the gate resistors.)
Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the transition of the
acknowledge signal at the optical receiver on the host controller side.
The transceivers required at the host controller side are not supplied with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.IGBT-Driver.com/go/fiberoptics
The connector and cable to the DC/DC power supply are not supplied with the gate driver, but via
FCI Inc. Recommended crimp contact housing: order code 65039-032; recommended crimp
contacts: 5 pcs, order code 48236-002. Refer to www.IGBT-Driver.com/go/fci
The recommended transmitter current at the host controller is 30-35mA, suitable for plastic optic
fibers with a length of less than 2.5 meters. A higher current may increase jitter or delay at turnoff.
The transmitter current at the gate driver is 30-35mA.
The delay from the turn-on transition at direct output of the gate drive unit to the turn-on of the
IGBT amounts to about 3.5μs (due to gate resistors). But turn-off at short circuit takes place with
0.5μs delay; so the real short-circuit time is 3μs shorter than the response time.
GND of the power supply is not at the same electrical potential as the auxiliary emitter terminal of
the IGBT. They should never be connected together.
Page 4
CT-Concept.com
1SD312F2
Data Sheet 1SD312F2-CM900HB-90H
Important Notice
The data contained in this product data sheet is intended exclusively for technically
trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance
with the respective safety regulations is mandatory!
Any handling of electronic devices is subject to the general specifications for protecting
electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX
or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with
these standards). Otherwise, this product may be damaged.
Disclaimer
This data sheet specifies devices but cannot promise to deliver any specific
characteristics. No warranty or guarantee is given – either expressly or implicitly –
regarding delivery, performance or suitability.
CT-Concept Technologie AG reserves the right to make modifications to its technical
data and product specifications at any time without prior notice. The general terms and
conditions of delivery of CT-Concept Technologie AG apply.
IGBT-Driver.com
Page 5
1SD312F2
Data Sheet 1SD312F2-CM900HB-90H
Ordering Information
The general terms and conditions of delivery of CT-Concept Technologie AG apply.
Related IGBT
CONCEPT Driver Type #
Mitsubishi CM900HB-90H
1SD312F2-CM900HB-90H
Information about Other Products
For drivers adapted to other high-voltage IGBT modules
Direct link: www.IGBT-Driver.com/go/plug-and-play
For other drivers and evaluation systems
Please click: www.IGBT-Driver.com
Manufacturer
CT-Concept Technologie AG
Intelligent Power Electronics
Renferstrasse 15
CH-2504 Biel-Bienne
Switzerland
Tel.
Fax
+41 - 32 - 344 47 47
+41 - 32 - 344 47 40
E-mail
Internet
Info@IGBT-Driver.com
www.IGBT-Driver.com
© Copyright 1999…2008 by CT-Concept Technologie AG - Switzerland.
We reserve the right to make any technical modifications without prior notice.
Page 6
All rights reserved.
Version from 2016-05-20
CT-Concept.com
1SD312F2-CM900HB-90H 价格&库存
很抱歉,暂时无法提供与“1SD312F2-CM900HB-90H”相匹配的价格&库存,您可以联系我们找货
免费人工找货