1SD418F2-5SNA1200E250100

1SD418F2 Data Sheet 1SD418F2-5SNA1200E250100 Single-Channel SCALE Plug-and-Play IGBT Driver Ultra-compact, high-performance driver for 2-level, 3-level and multilevel converters Abstract The SCALE plug-and-play driver 1SD418F2-5SNA1200E250100 is an ultracompact single-channel intelligent gate driver designed for ABB’s highvoltage IGBTs of type 5SNA1200E250100. The driver features a fiber-optic interface, a built-in DC/DC power supply and a selectable operating mode via a jumper. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to www.IGBT-Driver.com/go/plug-and-play Product Highlights  Plug-and-play solution  Protects the IGBT from short-circuit failure  Active clamping of V ce at turn-off  Extremely reliable; long service life  No electrolytic capacitors  Gate current up to ±18A  Electrical insulation 5000 V AC  Fiber-optic links  Monitoring of supply voltage and fiber optics  Switching frequency DC to max. 10kHz  Duty cycle 0... 100%  Built-in DC/DC power supply  Shortens application development time IGBT-Driver.com Applications  Three/multi-level converters  Two-level converters  Medium-voltage converters  Industrial drives  Traction  Railroad power supplies  Wind-power converters  Radiology and laser technology  Research  Almost all other conceivable applications Page 1 1SD418F2 Data Sheet 1SD418F2-5SNA1200E250100 Important Notes This data sheet contains only product-specific data. For a detailed description, mustread application notes and common data that apply to the whole series, please refer to the “Description & Application Manual for 1SD418F2 SCALE High-Voltage IGBT Drivers”. When applying SCALE plug-and-play drivers, please note that these drivers are specifically adapted to a particular type of IGBT module. Therefore, the type designation of SCALE plug-and-play drivers also includes the type designation of the corresponding IGBT module. These drivers are not valid for IGBT modules other than those specified. Incorrect use may result in failure. Mechanical and Electrical Interfaces Dimensions: 183 x 38 (47) mm. Mounting Principle: Direct screw mount on IGBT. Interface Remarks Part type # Drive signal input Status output Power supply connector Fiber-optic receiver (Notes 16,18) Fiber-optic transmitter (Notes 16,19) On-board connector (Note 17) HFBR-2522 HFBR-1522 77315-101-05 Power supply connector Designator Pin numbers Ground Supply voltage V DC GND 1, 2, 4, 5 3 Absolute Maximum Ratings Parameter Remarks Supply voltage V DC Gate peak current I out Average supply current I DC Output power DC/DC converter Switching frequency Test voltage (50Hz/1min) DC-link voltage Operating temperature Storage temperature VDC to GND (Note 1) Page 2 Note 8 Note 3 Notes 3,12 Note 12 Primary to output (Note 15) Note 5 Note 12 Min Max Units 0 16 -18 +18 400 4 10 5000 1700 -40 +85 -40 +90 V A mA W kHz V AC(eff) V °C °C CT-Concept.com 1SD418F2 Data Sheet 1SD418F2-5SNA1200E250100 Electrical Characteristics All data refer to +25°C and V DC = 15V unless otherwise specified Power supply Remarks Min Typ. Max Nominal supply voltage V DC Supply current I DC Efficiency η Turn-on threshold V th Hysteresis on/off Coupling capacitance C io VDC to GND (Note 1) Without load (Note 2) Internal DC/DC converter 14.5 Short-circuit protection Remarks V ce monitoring threshold Response time Response time Blocking time Between aux. terminals 3-level mode (Note 11) 2-level mode (Note 6) 2-level mode (Note 7) Timing characteristics Remarks Turn-on delay t pd(on) Turn-off delay t pd(off) Output rise time t r(out) Output fall time t f(out) Acknowledge delay time Acknowledge pulse width Note Note Note Note Gate output Remarks Turn-on gate resistor R g(on) Turn-off gate resistor R g(off) Note 8 Note 8 Electrical insulation Remarks Note 4 Note 4 Primary to output Min Typ. Max 50 Units V μs μs s Units 400 550 100 100 450 ns ns ns ns ns μs 0.7 1.8 Min Typ. Max Units 1.6 3.1 Ω Ω Min Typ. Max Units Operating voltage (Note 10) Continuous or repeated Test voltage (50Hz/1min) Primary to output (Note 15) Partial discharge extinction volt. IEC1287 /