SCALE™-2 1SP0635x2x1-33
1SP0635x2x1-33
Data Sheet
Compact, high-performance, plug-and-play single-channel IGBT driver based
on SCALE™-2 technology for individual and parallel-connected modules in
2-level, 3-level and multilevel converter topologies
Abstract
The SCALE™-2 plug-and-play driver 1SP0635x2x1-33 is a compact single-channel intelligent gate driver
designed for 3300V 130x140mm and 190x140mm IGBT modules. The master driver 1SP0635x2M1-33 features
a fiber-optic interface with a built-in isolated DC/DC power supply. It can be used as stand-alone driver or in
conjunction with up to three 1SP0635D2S1-33 slaves to drive up to four parallel-connected IGBT modules.
The turn-on and turn-off gate resistors as well as the auxiliary gate capacitor are not assembled
in order to provide maximum flexibility. They must be assembled by the user before start of
operation. Please refer to the paragraph on “Gate Resistor and Auxiliary Gate Capacitor Assembly” for the
recommended values.
For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to:
www.power.com/gate-driver/go/plug-and-play
Features
Applications
Plug-and-play solution
Allows parallel connection of IGBT modules
For 2-level, 3-level and multilevel topologies
Built-in isolated DC/DC power supply (master)
Fiber-optic links (master)
Built-in interface to 1SP0635D2S1 (slave)
Duty cycle 0...100%
Dynamic Advanced Active Clamping DA C
Dynamic IGBT short-circuit protection
Monitoring of supply voltage
Monitoring of gate voltage
Extremely reliable; long service life
Shortens application development time
Suitable for 3300V 130x140mm
2
Traction
Railroad power supplies
Light rail vehicles
HVDC
Flexible AC transmission systems (FACTS)
Medium-voltage converters
Industrial drives
Wind-power converters
Medical applications
Research
And many others
and 190x140mm IGBT modules
www.power.com/gate-driver
Page 1
SCALE™-2 1SP0635x2x1-33
Data Sheet
Safety Notice!
The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory!
Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive
devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the
workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged.
Important Product Documentation
This data sheet contains only product-specific data. For a detailed description, must-read application notes and
common data that apply to the whole series, please refer to the “Description & Application Manual for
1SP0635 SCALE-2 IGBT Drivers” on www.power.com/gate-driver/go/1SP0635.
The gate resistors as well as the auxiliary gate capacitor on this gate driver are not assembled in order to
provide maximum flexibility. For the values required for specific IGBT modules, refer to the paragraph on
“Gate Resistor and Auxiliary Gate Capacitor Assembly”. Use of gate resistors and gate auxiliary capacitors
other than those specified may result in failure.
Mechanical Dimensions
Dimensions: Refer to the relevant “Description and Application Manual”
Mounting principle: Connected to IGBT module with screws
Fiber-Optic Interfaces (1SP0635x2M1)
Interface
Remarks
Drive signal input
Drive signal input
Status output
Status output
1SP0635V, fiber-optic receiver (Notes 1, 2)
1SP0635S, fiber-optic receiver (Notes 1, 2)
1SP0635V, fiber-optic transmitter (Notes 1, 3)
1SP0635S, fiber-optic transmitter (Notes 1, 3)
Part type #
HFBR-2522ETZ
HFBR-2412Z
HFBR-1522ETZ
HFBR-1412Z
Electrical Connectors
Interface
Remarks
Power supply connector X1
Bus connectors X2 and X3
1SP0635x2M1, on-board connector (Note 4)
On-board connectors (Note 5)
www.power.com/gate-driver
Part type #
214012
214013
Page 2
SCALE™-2 1SP0635x2x1-33
Data Sheet
Absolute Maximum Ratings
Parameter
Remarks
Supply voltage VDC
Average supply current IDC
Average supply current IDC
Gate output power
VDC to GND (1SP0635x2M1)
1SP0635x2M1 only (Note 6)
1SP0635x2M1 with three 1SP0635D2S1 (Note 6)
1SP0635x2M1, Ta < 70°C (Note 7)
1SP0635x2M1, Ta = 85°C (Note 7)
1SP0635D2S1, Ta < 70°C (Note 8)
1SP0635D2S1, Ta = 85°C (Note 8)
1SP0635x2M1, Ta < 70°C (Note 31)
1SP0635x2M1, Ta = 85°C (Note 31)
1SP0635D2S1, Ta < 70°C (Note 31)
1SP0635D2S1, Ta = 85°C (Note 31)
Note 9
1SP0635x2M1, primary to secondary (Note 10)
Switching operation (Note 11)
Off state (Note 12)
Primary to secondary side
Between parallel connected drivers (Note 13)
Between parallel connected drivers (Note 14)
X2 and X3, total RMS value (Note 15)
X2 and X3, total peak value (Note 15)
Gate output power
Switching frequency F
Switching frequency F
Gate peak current Iout
Test voltage (50Hz/1min.)
DC-link voltage
Operating voltage
Max. emitter-emitter voltage
|dV/dt|
Max. interface current
Min
Operating temperature
Storage temperature
0
Max
Unit
-40
-40
16
V
400
mA
1130
mA
3
W
2.2
W
2.6
W
2
W
n.d.
kHz
n.d.
kHz
n.d.
kHz
n.d.
kHz
+35
A
6000 VAC(eff)
2200
V
2700
V
3300 Vpeak
200 Vpeak
50 kV/μs
4
Arms
20
Apeak
+85
°C
+90
°C
-35
Recommended Operating Conditions
Power Supply
Remarks
Min
Typ
Max
Unit
Supply voltage VDC
To GND
14.5
15
15.5
V
www.power.com/gate-driver
Page 3
SCALE™-2 1SP0635x2x1-33
Data Sheet
Electrical Characteristics
All data refer to +25°C and VDC = 15V unless otherwise specified
Power Supply
Remarks
Supply current IDC
Coupling capacitance Cio
Without load, only 1SP0635x2M1
Without load, per additional 1SP0635D2S1
1SP0635x2M1, DC/DC converter
Power Supply Monitoring
Remarks
Supply threshold Viso-Vee
Monitoring hysteresis
Secondary
Secondary
Secondary
Secondary
Secondary
Secondary
Bus to 1SP0635D2S1
Remarks
Supply voltage
Turn-off command
Turn-on command
Without load
With three slaves, full load
To COM
To COM
Gate Monitoring
Remarks
Turn-on threshold VGE,on,min
Turn-off threshold VGE,off,max
Filter delay
Gmean to E, set fault (Note 17)
Gmean to E, set fault (Note 17)
Note 17
Short-circuit Protection
Remarks
Static Vce-monitoring threshold
Response time
Delay to IGBT turn-off
Between auxiliary terminals (Note 18)
DC-link voltage = 2200V (Note 19)
DC-link voltage = 1500V (Note 19)
DC-link voltage = 1100V (Note 19)
DC-link voltage = 800V (Note 19)
After the response time (Note 20)
Timing Characteristics
Remarks
Turn-on delay td(on)
Turn-off delay td(off)
Note 21
Note 21
Monitoring hysteresis
Supply threshold Vee-VCOM
www.power.com/gate-driver
Min
side,
side,
side,
side,
side,
side,
clear fault
set fault (Note 16)
set/clear fault
clear fault
set fault (Note 16)
set/clear fault
Typ
Max
120
35
15
Unit
mA
mA
pF
Min
Typ
Max
Unit
12.1
11.5
0.35
5
4.7
0.15
12.6
12.0
13.1
12.5
5.15
4.85
5.3
5
V
V
V
V
V
V
Min
Typ
Max
25
24
0
15
Min
Typ
V
V
V
V
Max
12.9
-7.6
28
Min
Typ
Typ
190
185
Unit
V
V
μs
Max
143
5.9
6.0
6.2
8.3
0.3
Min
Unit
Unit
V
μs
μs
μs
μs
μs
Max
Unit
ns
ns
Page 4
SCALE™-2 1SP0635x2x1-33
Data Sheet
Timing Characteristics
Remarks
Min
Typ
Output rise time tr(out)
Output fall time tf(out)
Transmission delay of fault state
Delay to clear fault state
Acknowledge delay time
Acknowledge pulse width
G to E (Note 22)
G to E (Note 22)
Note 23
After IGBT short circuit (Note 24)
After gate-monitoring fault (Notes 24, 30)
Note 25
On host side
Gate Output
Remarks
Turn-on gate resistor Rg(on)
Turn-off gate resistor Rg(off)
Auxiliary gate capacitor Cge
Gate voltage at turn-on
Gate-voltage at turn-off
Note 26
Note 26
Note 26
Note 27
Without load (Note 27)
PDC/DC = 3W (Note 27)
PDC/DC = 6W (Note 27)
PDC/DC = 12W (Note 27)
Electrical Isolation
Remarks
Min
Typ
Max
Test voltage (50Hz/1s)
Primary to secondary side (Note 10)
6000
6050
6100 VAC(eff)
Partial discharge extinction volt.
Primary to secondary side (Note 28)
3630
Vpeak
Creepage distance
Primary to secondary side (Note 29)
21
mm
Primary to IGBT main emitter terminal
20
mm
Primary to secondary side (Note 29)
21
mm
Primary to IGBT main emitter terminal
13
mm
Clearance distance
Max
Unit
400
9
30
90
9
1
250
700
1050
ns
ns
ns
μs
μs
ns
ns
Min
Typ
Max
Unit
not assembled
not assembled
not assembled
15
-10.1
-9.8
-9.5
-9
Ω
Ω
nF
V
V
V
V
V
Unit
Footnotes to the Key Data
1)
2)
3)
4)
5)
6)
The transceivers required on the host controller side are not supplied with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.power.com/gate-driver/go/fiberoptics.
The recommended transmitter current at the host controller is 20mA. A higher current may increase
jitter or delay at turn-off.
The typical transmitter current at the gate driver is 18mA. In case of supply undervoltage, the
minimum transmitter current at the gate driver is 12mA: this is suitable for adequate plastic optical
fibers with a length of up to 10 meters.
This refers to the manufacturer ordering number, see www.power.com/gate-driver/go/ext_erni. The
customer-side connector as well as cables with different lengths can be supplied by Power
Integrations. Refer to the “Description & Application Manual for 1SP0635 SCALE-2 IGBT Drivers” for
more information.
This refers to the manufacturer ordering number, see www.power.com/gate-driver/go/ext_erni. These
connectors are to be used to connect 1SP0635x2M1 (master) or 1SP0635D2S1 (slave) to
1SP0635D2S1 (slave) if parallel connection of IGBT modules is required. Cables with different lengths
can be supplied by Power Integrations. Refer to the “Description & Application Manual for 1SP0635
SCALE-2 IGBT Drivers” for more information.
If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is
not protected against overload.
www.power.com/gate-driver
Page 5
SCALE™-2 1SP0635x2x1-33
Data Sheet
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
The given power can only be fully exploited without slaves 1SP0635D2S1 (no parallel connection of
IGBT modules). If the specified value is exceeded, this indicates a driver overload. It should be noted
that the driver is not protected against overload. From 70°C to 85°C, the maximum permissible output
power can be linearly interpolated from the given data.
The given power can be fully exploited with slaves 1SP0635D2S1 (parallel connection of IGBT
modules). If the specified value is exceeded, this indicates a driver overload. It should be noted that
the driver is not protected against overload. From 70°C to 85°C, the maximum permissible output
power can be linearly interpolated from the given data. Note that the DC/DC converter on the master
1SP0635x2M1 is dimensioned to supply the master as well as three connected slaves 1SP0635D2S1 at
full load.
The gate current is limited by the gate resistors located on the driver.
HiPot testing (= dielectric testing) must generally be restricted to suitable components. This gate
driver is suited for HiPot testing. Nevertheless, it is strongly recommended to limit the testing time to
1s slots. Excessive HiPot testing may lead to insulation degradation.
This limit is due to active clamping under switching conditions. Refer to the “Description & Application
Manual for 1SP0635 SCALE-2 IGBT Drivers”.
Due to the Dynamic Active Advanced Clamping Function (DA 2C) implemented on the driver, the DClink voltage can be increased in the off-state condition (e.g. after emergency shut-down). This value is
only valid when the IGBTs are in the off state (not switching). The time during which the voltage can
be applied should be limited to short periods (< 60 seconds). Refer to the “Description & Application
Manual for 1SP0635 SCALE-2 IGBT Drivers”.
The maximum dynamic voltage between auxiliary emitters of parallel-connected drivers due to
asymmetrical operation at turn-on and turn-off must be limited to the given value.
Maximum allowed rate of change between auxiliary emitter voltages of parallel connected drivers.
Dynamic voltages between auxiliary emitters of parallel connected drivers at turn-on and turn-off lead
to equalizing currents over the X2 or X3 bus. The peak and RMS values of the resulting current must
be limited to the given value.
Undervoltage monitoring of the secondary-side supply voltage (Viso to Vee and Vee to COM which
correspond with the approximate turn-on and turn-off gate-emitter voltages). If the corresponding
voltage drops below this limit on 1SP0635x2M1 (masters), all paralleled IGBTs (master and slaves) are
switched off and a fault is transmitted to the status output. If the corresponding voltage drops below
this limit on 1SP0635D2S1 (slaves), the corresponding IGBT is switched off. A fault will be generated
by the gate-monitoring function on the master which will turn off all paralleled IGBTs after the
corresponding delay.
The mean value VGE,mean of all gate voltages (master and all slaves) is filtered and compared to the
given values at turn-on and turn-off. If the specified values are exceeded (V GE,meanVGE,off,max at turn-off) after the given filter delay, the driver turns off all parallelconnected IGBTs and a fault is transmitted to the status output.
A dynamic Vce protection is implemented on the driver. The maximum allowed Vce voltage at turn-on
is dynamically adjusted in order to better fit the IGBT characteristics at turn-on. At the end of the
turn-on process, the given static value applies.
The resulting pulse width of the direct output of the gate drive unit for short-circuit type I (excluding
the delay of the gate resistors) is the sum of the response time plus the delay to IGBT turn-off.
The turn-off event of the IGBT is delayed by the specified time after the response time.
Including the delay of the external fiber-optic links (cable length: 1m). Measured from the transition
of the turn-on or turn-off command at the optical transmitter on the host controller side to the direct
output of the gate drive unit (excluding the delay of the gate resistors).
Output rise and fall times are measured between 10% and 90% of the nominal output swing. The
values are given for the driver side of the gate resistors with 2Ω/1uF load. The time constant of the
output load in conjunction with the present gate resistors leads to an additional delay at their load
side.
Delay of external fiber-optic links. Measured from the driver secondary side (ASIC output) to the
optical receiver on the host controller (cable length: 1m).
Measured on the host side. The fault status on the secondary side is automatically reset after the
specified time.
www.power.com/gate-driver
Page 6
SCALE™-2 1SP0635x2x1-33
Data Sheet
25)
26)
27)
28)
29)
30)
31)
Including the delay of the external fiber-optic links (cable length: 1m). Measured from the transition
of the turn-on or turn-off command at the optical transmitter on the host controller side to the
transition of the acknowledge signal at the optical receiver on the host controller side.
The gate resistors and the auxiliary gate capacitor are not assembled on this IGBT gate driver. They
must be assembled by the user according to the paragraph on “Gate Resistor and Auxiliary Gate
Capacitor Assembly”.
The driver secondary side voltage is split into two distinct voltages on the driver. The first one is the
turn-on voltage which is regulated at about 15V. The difference between the total secondary side
voltage and the turn-on voltage is the turn-off voltage which is not regulated and mainly dependent
on the driver input voltage VDC and the DC/DC converter power.
Partial discharge measurement (transformer only) is performed in accordance with IEC 60270.
Clearance and creepage distances are designed according to IEC 60077-1. Refer to the “Description &
Application Manual for 1SP0635 SCALE-2 IGBT Drivers” for more information.
The fault status is set as long as the gate monitoring fault is present. The given value applies if the
driver goes from the “off state” to the “on state” and the gate-emitter voltage of one or more parallel
connected drivers does not turn on. If the driver goes from the “on state” to the “off state” and the
gate-emitter voltage of one or more parallel connected drivers does not turn off, the fault status is
applied as long as the gate monitoring fault is present.
The maximum switching frequency is not defined, as it depends on the IGBT module used. Please
consult the corresponding driver data sheet for more information.
www.power.com/gate-driver
Page 7
SCALE™-2 1SP0635x2x1-33
Data Sheet
Gate Resistor and Auxiliary Gate Capacitor Assembly
The turn-on and turn-off gate resistors as well as the auxiliary gate capacitor of 1SP0635x2x1 drivers are
adapted to their respective IGBT modules.
Recommended gate resistors (R168, R169, R178 and R179): PR02 / 2W / 5% from Vishay.
Recommended auxiliary gate capacitor (C105): 1206 / X7R / 25V / 5%
The following versions exist:
3300V IGBT Type
R178/
R179
R168/
R169
Resulting
Rg,on
Resulting
Rg,off
C105
2.7Ω
4.7Ω
1.35Ω
2.35Ω
150nF
4.7Ω
6.8Ω
2.35Ω
3.4Ω
not assembled
5.6Ω
18Ω
2.8Ω
9Ω
220nF
1MBI800UG-330
5.1Ω
7.5Ω
2.55Ω
3.75Ω
not assembled
CM800HC-66H
7.5Ω
7.5Ω
3.75Ω
3.75Ω
330nF
DIM1000NSM33-TS000
TIM1000NSM33-TS000
MBN1000E33E2
MBL1000E33E2-B
4.3Ω
4.3Ω
2.15Ω
2.15Ω
220nF
8.2Ω
12Ω
4.1Ω
6Ω
100nF
FZ1000R33HE3
1.5Ω
6.8Ω
0.75Ω
3.4Ω
220nF
FZ1000R33HL3
1.5Ω
12Ω
0.75Ω
6Ω
220nF
CM1000HC-66R
5.1Ω
18Ω
2.55Ω
9Ω
not assembled
5SNA1000N330300
3Ω
4.7Ω
1.5Ω
2.35Ω
220nF
5SNE1000E330300
3Ω
4.7Ω
1.5Ω
2.35Ω
220nF
5SNA1200E330100
3Ω
4.7Ω
1.5Ω
2.35Ω
not assembled
DIM1200ESM33-F000
TIM1200ESM33
3.3Ω
10Ω
1.65Ω
5Ω
330nF
1MBI1200UE-330
3.3Ω
4.7Ω
1.65Ω
2.35Ω
not assembled
MBN1200E33D
6.8Ω
10Ω
3.4Ω
5Ω
not assembled
MBN1200E33E
8.2Ω
12Ω
4.1Ω
6Ω
not assembled
MBN1200F33F
15Ω
18Ω
7.5Ω
9Ω
not assembled
FZ1200R33KF2C
1.8Ω
3.6Ω
0.9Ω
1.8Ω
220nF
FZ1200R33HE3
1.3Ω
6.8Ω
0.65Ω
3.4Ω
220nF
CM1200HC-66H
3.9Ω
5.1Ω
1.95Ω
2.55Ω
330nF
CM1200HC-66X
4.7Ω
36Ω
2.35Ω
18Ω
N.A.
CM1200HCB-66X
4.7Ω
36Ω
2.35Ω
18Ω
N.A.
FZ800R33KF2C
FD800R33KF2C
FD800R33KF2C-K
5SNA0800N330100
5SNE0800E330100
DIM800NSM33-F000
TIM800NSM33
www.power.com/gate-driver
Page 8
SCALE™-2 1SP0635x2x1-33
Data Sheet
3300V IGBT Type
R178/
R179
R168/
R169
Resulting
Rg,on
Resulting
Rg,off
C105
FZ1400R33HE4
1.6Ω
8.2Ω
0.8Ω
4.1Ω
not assembled
FZ2000R33HE3
1Ω
6.8Ω
0.5Ω
3.4Ω
not assembled
5SNA1500E330300
2Ω
4.7Ω
1Ω
2.35Ω
220nF
5SNA1500E330305
2Ω
5.6Ω
1Ω
2.8Ω
330nF
DIM1500ESM33-TS000
3.3Ω
4.7Ω
1.65Ω
2.35Ω
330nF
DIM1500ESM33-PR500
2Ω
6.8Ω
1Ω
3.4Ω
330nF
1MBI1500UE-330
3.3Ω
4.3Ω
1.65Ω
2.15Ω
not assembled
1MBI1500UE-330B
1Ω
3Ω
0.5Ω
1.5Ω
220nF
MBN1500E33E2
5.6Ω
8.2Ω
2.8Ω
4.1Ω
330nF
FZ1500R33HE3
1Ω
4.7Ω
0.5Ω
2.35Ω
330nF
FZ1500R33HL3
1Ω
6.8Ω
0.5Ω
3.4Ω
330nF
YMIF1500-33
4.7Ω
8.2Ω
2.35Ω
4.1Ω
330nF
CM1500HC-66R
3.3Ω
16Ω
1.65Ω
8Ω
not assembled
MG1500FXF1US62
3Ω
6.8Ω
1.5Ω
3.4Ω
not assembled
MBN1800F33F
10Ω
13Ω
5Ω
6.5Ω
not assembled
CM1800HC-66X
3Ω
24Ω
1.5Ω
12Ω
not assembled
5SNA1800E330400
2.7Ω
15Ω
1.35Ω
7.5Ω
330nF
FZ2000R33HE3
1Ω
6.8Ω
0.5Ω
3.4Ω
not assembled
For the component position, refer to Figs. 1 and 2.
www.power.com/gate-driver
Page 9
SCALE™-2 1SP0635x2x1-33
Data Sheet
Assembly Drawing
Fig. 1: Assembly drawing of 1SP0635x2M1 with highlighted gate resistors
Fig. 2: Assembly drawing of 1SP0635D2S1 with highlighted gate resistors
Note that the wires of the gate resistors should not project more than 1.6mm after soldering (excess length at
bottom side). Furthermore, a minimum distance of 1mm must be maintained between the gate resistor body
and the PCB.
Legal Disclaimer
The statements, technical information and recommendations contained herein are believed to be accurate as
of the date hereof. All parameters, numbers, values and other technical data included in the technical
information were calculated and determined to our best knowledge in accordance with the relevant technical
norms (if any). They may base on assumptions or operational conditions that do not necessarily apply in
general. We exclude any representation or warranty, express or implied, in relation to the accuracy or
completeness of the statements, technical information and recommendations contained herein. No
responsibility is accepted for the accuracy or sufficiency of any of the statements, technical information,
recommendations or opinions communicated and any liability for any direct, indirect or consequential loss or
damage suffered by any person arising therefrom is expressly disclaimed.
www.power.com/gate-driver
Page 10
SCALE™-2 1SP0635x2x1-33
Data Sheet
Ordering Information
Our international terms and conditions of sale apply.
Interface
Master, Fiber-Optic Interface
Master, Fiber-Optic Interface
Slave, Electrical Interface
1)
2)
1)
2)
Power Integrations Driver Type #
Related IGBT
1SP0635V2M1-33
1SP0635S2M1-33
1SP0635D2S1-33
3300V IGBT modules
3300V IGBT modules
3300V IGBT modules
Fiber-optic interface with versatile link (HFBR-2522ETZ and HFBR-1522ETZ)
Fiber-optic interface with ST (HFBR-2412Z and HFBR-1412Z)
See “Description & Application Manual for 1SP0635 SCALE-2 IGBT Drivers”
Product home page: www.power.com/gate-driver/go/1SP0635
Refer to www.power.com/gate-driver/go/nomenclature for information on driver nomenclature
Information about Other Products
For other drivers, evaluation systems, product documentation and application support
Please click onto: www.power.com/gate-driver
© 2010…2020 Power Integrations Switzerland GmbH.
We reserve the right to make any technical modifications without prior notice.
www.power.com/gate-driver
All rights reserved.
Version 3.3 from 2020-04-22
Page 11
SCALE™-2 1SP0635x2x1-33
Data Sheet
Power Integrations Sales Offices
WORLD HEADQUARTERS
5245 Hellyer Avenue
San Jose, CA 95138 USA
Tel: +1-408-414-9200
Fax: +1-408-414-9765
Email: usasales@power.com
AMERICAS EAST
7360 McGinnis Ferry Road
Suite 225
Suwannee, GA 30024 USA
Tel: +1-678-957-0724
Fax: +1-678-957-0784
Email: usasales@power.com
AMERICAS CENTRAL
333 Sheridan Road
Winnetka, IL 60093 USA
Tel: +1-847-721-6293
Email: usasales@power.com
AMERICAS WEST
5245 Hellyer Avenue
San Jose, CA 95138 USA
Tel: +1-408-414-8778
Fax: +1-408-414-3760
Email: usasales@power.com
CHINA (Shanghai)
Room 2410, Charity Plaza
No. 88 North Caoxi Road
Shanghai, 200030 China
Tel: +86-21-6354-6323
Fax: +86-21-6354-6325
Email: chinasales@power.com
CHINA (Shenzhen)
17/F, Hivac Building, No 2
Keji South 8th Road, Nanshan District
Shenzhen, 518057 China
Tel: +86-755-8672-8689
Fax: +86-755-8672-8690
Email: chinasales@power.com
GERMANY (AC-DC/LED Sales)
Einsteinring 24
85609 Aschheim, Germany
Tel: +49-89-5527-39100
Fax: +49-89-1228-5374
Email: eurosales@power.com
GERMANY (Gate Driver Sales)
HellwegForum 1
59469 Ense, Germany
Tel: +49-2938-64-39990
Email: gate-drivers.sales@power.com
INDIA (Bangalore)
#1, 14th Main Road
Vasanthangar
Bangalore, 560052 India
Tel 1: +91-80-4113-8020
Tel 2: +91-80-4113-8028
Fax: +91-80-4113-8023
Email: indiasales@power.com
INDIA (Mumbai)
Unit: 106-107, Sagar Tech Plaza-B
Sakinaka, Andheri Kurla Road
Mumbai, Maharashtra 400072 India
Tel 1: +91-22-4003-3700
Tel 2: +91-22-4003-3600
Email: indiasales@power.com
INDIA (New Delhi)
#45, Top Floor
Okhla Industrial Area, Phase - III
New Delhi, 110020 India
Tel 1: +91-11-4055-2351
Tel 2: +91-11-4055-2353
Email: indiasales@power.com
ITALY
Via Milanese 20
20099 Sesto San Giovanni (MI), Italy
Tel: +39-02-4550-8708
Email: eurosales@power.com
JAPAN
Kosei Dai-3 Bldg.
2-12-11, Shin-Yokohama, Kohoku-ku
Yokohama-shi, Kanagawa
Japan 222-0033
Tel: +81-45-471-1021
Fax: +81-45-471-3717
Email: japansales@power.com
KOREA
RM602, 6FL, 22
Teheran-ro 87-gil, Gangnam-gu
Seoul, 06164 Korea
Tel: +82-2-2016-6610
Fax: +82-2-2016-6630
Email: koreasales@power.com
SINGAPORE
51 Newton Road
#19-01/05 Goldhill Plaza
Singapore, 308900
Tel 1: +65-6358-2160
Tel 2: +65-6358-4480
Fax: +65-6358-2015
Email: singaporesales@power.com
TAIWAN
5F, No. 318, Nei Hu Rd., Sec. 1
Nei Hu Dist.
Taipei, 114 Taiwan
Tel: +886-2-2659-4570
Fax: +886-2-2659-4550
Email: taiwansales@power.com
UNITED KINGDOM
Building 5, Suite 21
The Westbrook Centre
Milton Road
Cambridge, CB4 1YG United Kingdom
Tel: +44-7823-557-484
Email: eurosales@power.com
www.power.com/gate-driver
Page 12