LYT0002/0004-0006
LYTSwitch-0 Off-Line Low Power
LED Driver IC Family
Lowest Component Count, Off-Line Switcher IC
for Non-Isolated LED Lighting Applications
Product Highlights
•
•
•
•
High power factor meeting EU and USA requirements
Very low component count
Frequency jitter reduces EMI
No bias supply or transformer required
FB
VIN
FB
+
Power Factor Correction
Allows designs that easily meet European and North American
standards for PFC in consumer lighting applications.
LYTSwitch-0 Supports Different LED Applications
Flyback, buck, buck-boost and boost architectures are all
supported by the LYTSwitch-0 family. The 700 V switching power
MOSFET supports an input voltage range of 85 VAC to 308 VAC.
VIN
D
The LYTSwitch™-0 family is specifically designed for low cost
LED bulb replacement applications. LYTSwitch-0 devices
integrate a 700 V power MOSFET, oscillator, simple ON/OFF
control scheme, a high-voltage switched current source,
frequency jittering, cycle-by-cycle current limit and thermal
shutdown circuitry into a monolithic IC.
The start-up and operating power are derived directly from the
voltage on the DRAIN pin. This eliminates the need for a bias
supply and associated circuitry plus allowing low-cost discrete
inductors to be used. The fully integrated auto-restart circuit in
the LYTSwitch-0 family safely limits output power during fault
conditions such as short-circuit or open-loop, reducing component
count and lower system cost. Package options for thru-hole and
surface-mount suit different manufacturing requirements.
BP
S
LYTSwitch-0
PI-6819a-060613
(b)
Figure 1. Typical Application Schematic (a) Buck, (b) Buck-Boost.
Output Current Table1
Product6
PF4,5
LYT0002D/P
LYT0004D/P
LYT0005D/P
LYT0006D/P
Description
PI-6810-060613
(a)
66 kHz operation together with frequency jittering insures a very
low-cost EMI filter. Less than 0.7 @ 120 VAC and >0.5 @ 230 VAC.
5. PF low: for non-PF application where CIN >5 mF minimum.
6. Packages: P: PDIP-8B, D: SO-8C.
SO-8C (D Package)
Figure 2.
PDIP-8B (P Package)
Package Options.
www.power.com
June 2015
This Product is Covered by Patents and/or Pending Patent Applications.
LYT0002/0004-0006
Topology
Basic Circuit Schematic
Key Features
FB
High-Side
Buck –
Direct
Feedback
BP
D
+
S
•
LYTSwitch-0
•
•
VIN
•
Output referenced to input
Positive output (VO) with respect to -VIN
Step down – VO < VIN
Low cost direct feedback (±5% typ.)
PI-7043-053113
•
Low-Side
Buck –
Constant
Current LED
Driver;
Optocoupler
Feedback
PI-7044-060313
+
•
IO
VIN
•
•
VF +
BP
FB
D
S
R=
LYTSwitch-0
VF
IO
•
•
High-Side
Buck-Boost –
Constant
Current LED
Driver
FB
D
RSENSE
BP
IO
S
•
•
•
LYTSwitch-0
VIN
•
PI-7045-060313
Output referenced to input
Negative output (VO) with respect to +VIN
Step down – VO < VIN
Optocoupler feedback
• Low-cost non-safety rated optocoupler
• Optional Zener provides disconnected load
protection
• Accuracy determined by VF variation of
optocoupler LED
Output referenced to input
Negative output (VO) with respect to +VIN
Step up/down – VO > VIN or VO < VIN
Low-cost direct feedback (±5% typ.)
Fail-safe – output is not subjected to input voltage
if the internal power MOSFET fails
Ideal for driving LEDs – better accuracy and
temperature stability than low-side Buck constant
current LED driver
+
Low-Side
Boost –
Constant
Current LED
Driver
•
•
D
VIN
LYTSwitch-0
•
FB
•
BP
•
S
Output referenced to input
Positive output (VO) with respect to -VIN
Step up – VO > VIN
Low-cost direct feedback (±5% typ.)
Ideal for driving high-voltage LEDs string – good
accuracy and temperature stability
PI-7046-053113
•
+
•
Low-Side
Flyback –
Constant
Current LED
Driver
•
D
VIN
LYTSwitch-0
•
•
FB
BP
•
S
•
Output referenced to input
Positive output (VO) with respect to -VIN
Step down – VO < VIN
Low-cost direct feedback (±5% typ.)
Fail-safe – output is not subjected to input voltage
if the internal power MOSFET fails
Ideal for driving very low voltage LEDs string –
good accuracy and temperature stability
PI-7047-060313
Table 2. Common Circuit Configurations Using LYTSwitch-0 for Driving LEDs.
2
Rev. B 06/15
www.power.com
LYT0002/0004-0006
BYPASS
(BP)
DRAIN
(D)
REGULATOR
5.8 V
+
5.8 V
4.85 V
BYPASS PIN
UNDERVOLTAGE
-
CURRENT LIMIT
COMPARATOR
+
6.3 V
VI
-
LIMIT
JITTER
CLOCK
DCMAX
FEEDBACK
(FB)
THERMAL
SHUTDOWN
OSCILLATOR
1.65 V -VT
S
Q
R
Q
LEADING
EDGE
BLANKING
SOURCE
(S)
PI-3904-032213
Figure 3a. Functional Block Diagram LYT0002.
BYPASS
(BP)
DRAIN
(D)
REGULATOR
5.8 V
FAULT
PRESENT
AUTORESTART
COUNTER
6.3 V
CLOCK
RESET
+
5.8 V
4.85 V
BYPASS PIN
UNDERVOLTAGE
CURRENT LIMIT
COMPARATOR
-
+
-
VI
LIMIT
JITTER
CLOCK
DCMAX
FEEDBACK
(FB)
OSCILLATOR
THERMAL
SHUTDOWN
1.65 V -VT
S
Q
R
Q
LEADING
EDGE
BLANKING
SOURCE
(S)
PI-2367-032213
Figure 3b. Functional Block Diagram LYT0004-0006.
3
www.power.com
Rev. B 06/15
LYT0002/0004-0006
Pin Functional Description
DRAIN (D) Pin:
Power MOSFET Drain connection. Provides internal operating
current for both start-up and steady-state operation.
BYPASS (BP) Pin:
Connection point for a 0.1 mF external bypass capacitor for the
internally generated 5.8 V supply.
FEEDBACK (FB) Pin:
During normal operation, switching of the power MOSFET is
controlled by this pin. Power MOSFET switching is terminated
when a current greater than 49 µA is delivered into this pin.
SOURCE (S) Pin:
This pin is the power MOSFET source connection. It is also the
ground reference for the BYPASS and FEEDBACK pins.
P Package (PDIP-8B)
S
1
8
S
S
2
7
S
BP
FB
D Package (SO-8C)
BP
FB
1
8
2
7
6
3
5
4
D
D
4
3a
5
S
S
S
S
3b
PI-6899-060613
Figure 4. Pin Configuration.
LYTSwitch-0 Functional Description
LYTSwitch-0 combines a high-voltage power MOSFET switch
with a power supply controller in one device. Unlike conventional
PWM (pulse width modulator) controllers, LYTSwitch-0 uses a
simple ON/OFF control to regulate the output voltage. The
LYTSwitch-0 controller consists of an oscillator, feedback (sense
and logic) circuit, 5.8 V regulator, BYPASS pin undervoltage circuit,
over-temperature protection, frequency jittering, current limit
circuit, leading edge blanking and a 700 V power MOSFET. The
LYTSwitch-0 incorporates additional circuitry for auto-restart.
Oscillator
The typical oscillator frequency is internally set to an average of
66 kHz. Two signals are generated from the oscillator: the
maximum duty cycle signal (DCMAX) and the clock signal that
indicates the beginning of each cycle.
The LYTSwitch-0 oscillator incorporates circuitry that introduces
a small amount of frequency jitter, typically 4 kHz peak-to-peak,
to minimize EMI emission. The modulation rate of the frequency
jitter is set to 1 kHz to optimize EMI reduction for both average
and quasi-peak emissions. The frequency jitter should be
measured with the oscilloscope triggered at the falling edge of
the Drain waveform. The waveform in Figure 5 illustrates the
frequency jitter of the LYTSwitch-0.
Feedback Input Circuit
The feedback input circuit at the FEEDBACK pin consists of a
low impedance source follower output set at 1.65 V. When the
current delivered into this pin exceeds 49 µA, a low logic level
(disable) is generated at the output of the feedback circuit. This
output is sampled at the beginning of each cycle on the rising
edge of the clock signal. If high, the power MOSFET is turned
on for that cycle (enabled), otherwise the power MOSFET remains
off (disabled). Since the sampling is done only at the beginning
of each cycle, subsequent changes in the FEEDBACK pin
voltage or current during the remainder of the cycle are ignored.
5.8 V Regulator and 6.3 V Shunt Voltage Clamp
The 5.8 V regulator charges the bypass capacitor connected to
the BYPASS pin to 5.8 V by drawing a current from the voltage
on the DRAIN, whenever the power MOSFET is off. The BYPASS
pin is the internal supply voltage node for the LYTSwitch-0.
When the power MOSFET is on, the LYTSwitch-0 runs off of the
energy stored in the bypass capacitor. Extremely low power
consumption of the internal circuitry allows the LYTSwitch-0 to
operate continuously from the current drawn from the DRAIN
pin. A bypass capacitor value of 0.1 µF is sufficient for both
high frequency decoupling and energy storage.
BYPASS Pin Undervoltage
The BYPASS pin undervoltage circuitry disables the power
MOSFET when the BYPASS pin voltage drops below 4.85 V.
Once the BYPASS pin voltage drops below 4.85 V, it must rise
back to 5.8 V to enable (turn-on) the power MOSFET.
Over-Temperature Protection
The thermal shutdown circuitry senses the die temperature.
The threshold is set at 142 °C typical with a 75 °C hysteresis.
When the die temperature rises above this threshold (142 °C)
the power MOSFET is disabled and remains disabled until the
die temperature falls by 75 °C, at which point it is re-enabled.
Current Limit
The current limit circuit senses the current in the power
MOSFET. When this current exceeds the internal threshold
(ILIMIT ), the power MOSFET is turned off for the remainder of that
cycle. The leading edge blanking circuit inhibits the current limit
comparator for a short time (tLEB) after the power MOSFET is
turned on. This leading edge blanking time has been set so
that current spikes caused by capacitance and rectifier reverse
recovery time will not cause premature termination of the
switching pulse cycle.
Auto-Restart (LYT0004-0006)
In the event of a fault condition such as output overload, output
short, or an open loop condition, LYTSwitch-0 enters into
auto-restart operation. An internal counter clocked by the
oscillator gets reset every time the FEEDBACK pin is pulled
4
Rev. B 06/15
www.power.com
LYT0002/0004-0006
while still meeting conducted EMI limits. Power factor is >0.5
at 230 VAC and >0.7 PF at 120 VAC meeting requirements for
LED lamps in Europe and USA.
PI-3660-081303
600
500
VDRAIN
400
The input stage comprises fusible resistor RF1, bridge rectifier
BR1, capacitors C1 and C2, and inductor L1. Resistor RF1 is a
flame proof, fusible, wire wound resistor. It accomplishes
several functions: a) Inrush current limitation to below specification
of BR1; b) Differential mode conducted EMI noise attenuation; c)
Fuse should any other component fail short-circuit; d) Higher
power factor. Capacitor C1, C2 and inductor L1 forms a π filter
to reduce differential mode EMI. Capacitor C2 provides local
decoupling for the switching current through U1. There is an
optional parallel resistor on the board across L1 which damps
the resonance of the pi filter.
300
200
100
0
68 kHz
64 kHz
0
20
The power processing stage is formed by the integrated
MOSFET switch within LYT0006 (U1), a free-wheeling diode
(D1), sense resistor (R2), power inductor (L2) and output
capacitor (C5). To reduce reverse recovery losses in D1 the
value of L2 was designed such that the converter operates in
mostly discontinuous conduction mode. Diode D1 is an
ultrafast diode with a reverse recovery time (tRR) ≈35 ns. This
recovery is recommended due to the high ambient operating
time temperature which will increase diode reverse recovery
charge. A bobbin based EE10 core size indictor was selected
for L2 in order to prevent changes in inductance value when
placed inside a metal enclosure. Lower cost drum core or dog
bone inductor types may also be used, however these have an
open magnetic path which can be shorted by a metal enclosure.
This reduces the effective inductance and requires the value to
be adjusted to take this into account when placed inside the
final enclosure.
Time (µs)
Figure 5. Frequency Jitter.
high. If the FEEDBACK pin is not pulled high for 50 ms, the
power MOSFET switching is disabled for 800 ms. The autorestart alternately enables and disables the switching of the
power MOSFET until the fault condition is removed.
Applications Example
A 6 W (Output) Universal Input Buck LED Driver Converter
The circuit shown in Figure 6 is a typical implementation of a
non-isolated, power factor corrected buck power supply for
LED driver applications. The simplicity and low component
count make this ideal for space constrained, cost sensitive
designs such as GU10 or A19 size lamps. This design was
optimized to drive an LED string at a voltage of 54 V with a
constant current of 110 mA, giving 6 W of output power. The
design operates over a universal input range from 90 VAC to
265 VAC and achieves an output current tolerance of < ±5%
at nominal line voltage. The input capacitance (C1 + C2) was
reduced to achieve the highest possible power factor input
Capacitor C5 is the output filter capacitor; its primary function is
to limit the output current ripple and ensures high frequency
currents flow within as small as a loop area as possible to
reduce EMI.
R1
4.7 kΩ
FB
L
RF1
4.7 Ω
90 - 265
VAC
L1
4.7 mH
BR1
MB6S
600 V
RV1*
275 VAC
C1
47 nF
630 V
BP
D
C4
C3
22 µF
100 nF 16 V
25 V
S
LYTSwitch-0
U1
LYT0006P
4
5
L2
54 V, 110 mA
+
R2
18.7 Ω
1%
C2
330 nF
450 V
C5
47 µF
63 V
D1
MURS160T3G
N
*Optional 75 ns) diodes should never be
used as the large reverse recovery currents can cause
excessive power dissipation in the diode and/or exceed the
maximum drain current specification of LYTSwitch-0.
Inductor L1
Choose any standard off-the-shelf inductor that meets the
design requirements. A “drum” or “dog bone” “I” core inductor
is recommended with a single ferrite element due to its low-cost
and very low audible noise properties. The typical inductance
value and RMS current rating can be obtained from the
LYTSwitch-0 PIXls design spreadsheet. The PIXls application is
part of the PI Expert design suite available for free download
from Power Integrations. Choose L1 greater than or equal to
the typical calculated inductance.
Note that the open magnetic path of non-shielded discrete
inductors may cause inductance value changes when placed
within metal enclosure requiring a larger value to be used.
6
Rev. B 06/15
www.power.com
LYT0002/0004-0006
Output Capacitor C5
The primary function of capacitor C5 is to smooth the inductor
current. Select a low or ultra-low ESR series if electrolytic types
are used to ensure capacitor heating is minimized. Ceramic or
solid polymer types are also suitable but are typically higher
cost per unit capacitance.
Feedback Capacitor C4
Capacitor C4 can be a low-cost general purpose capacitor. It
provides a “sample and hold” function, charging to the sensed
current value during the off-time of LYTSwitch-0. Its value
should be 10 mF to 22 mF; smaller values cause poorer regulation
and lower efficiency. This capacitor also bypasses the switching
current during the free-wheeling period, reducing the sense
resistor dissipation.
Select the voltage rating to be the nearest above the LED string
voltage. Select the initial capacitance value based on the ripple
current parameter calculated in the design spreadsheet. The
capacitance value may be further increased to reduce the LED
ripple current dependent on the specification requirements of
the driver. For long life use 105 °C or above rated parts unless
the ambient temperature inside the lamp is less than 80 °C and
select a series with an appropriate lifetime rating. Note that
operating electrolytic capacitors below their rated temperature
specification will significantly extend their lifetime e.g., 105 °C
capacitor operated at 80 °C will increase lifetime by a factor of
2 to 3.
LYTSwitch-0 Layout Considerations
In the buck or buck-boost converter configuration, since the
SOURCE pins in LYTSwitch-0 are switching nodes, the copper
area connected to SOURCE should be minimized to minimize
EMI within the thermal constraints of the design.
In the boost and non-isolated flyback configuration, since the
SOURCE pins are tied to DC return, the copper area connected
to SOURCE can be maximized to improve heat sinking.
The loop formed between the LYTSwitch-0, inductor (L2),
free-wheeling diode (D1), and output capacitor (C5) should be
kept as small as possible. The BYPASS pin capacitor C3
(Figure 7a) should be located physically close to the SOURCE (S)
and BYPASS (BP) pins. To minimize direct coupling from
Sense Resistor R2
Sense resistor should be a 1% tolerance and either pulse rated
or overdesigned to avoid resistance drift with time. If using a
standard metal film type, overdesign power rating by 2-4 times.
The value of the resistor is provided in the design spreadsheet.
U1
D
L1
S
RF1
LYTSwitch-0
R1
FB
S
AC
INPUT
R3
C4
D1
R2 BP
C3
S
S
VR1
RV1
C1
~
+
~
–
C2
BR1
DC
OUTPUT
L2
C5
+
Optimize hatched copper areas (
) for heat sinking.
PI-7033-052913
Figure 7a. Recommended Printed Circuit Layout for LYTSwitch-0 in a Buck Converter Configuration using P Package.
7
www.power.com
Rev. B 06/15
LYT0002/0004-0006
U1
C2
R1
FB
BP
RV1
~
RF1
+
~
D1
C4
C1
R3
AC
INPUT
R2
L1
+
S
S
S
S
LYTSwitch-0
D
C5
VR1
DC
OUTPUT
C3
L2
–
BR1
Optimize hatched copper areas (
) for heat sinking.
PI-7032-061313
Figure 7b. Recommended Printed Circuit Layout for LYTSwitch-0 in a Buck Converter Configuration using D Package to Bottom Side of the Board.
switching nodes, the LYTSwitch-0 should be placed away from
AC input lines. It may be advantageous to place capacitors C1
and C2 in-between LYTSwitch-0 and the AC input.
Quick Design Checklist
As with any power supply design, all LYTSwitch-0 designs
should be verified for proper functionality on the bench. The
following minimum tests are recommended:
1. Correct diode selection – UF400x series diodes are
recommended only for designs that operate in MDCM at an
ambient of 70 °C or below. For designs operating in
continuous conduction mode (CCM) and/or higher ambient,
then a diode with a reverse recovery time of 35 ns or better,
such as the BYV26C, is recommended.
2. Maximum drain current – Verify that the peak drain current is
below the data sheet peak drain specification under
worst-case conditions of highest line voltage, maximum
overload (just prior to auto-restart) and highest ambient
temperature.
3. Thermal check – At maximum output power, minimum input
voltage and maximum ambient temperature, verify that the
LYTSwitch-0 SOURCE pin temperature is 110 °C or below.
This figure ensures adequate margin due to variations in
RDS(ON) from part to part. A battery powered thermocouple
meter is recommended to make measurements when the
SOURCE pins are a switching node. Alternatively, the
ambient temperature may be raised to indicate margin to
thermal shutdown.
4. Check for any presence of reverse current in the DRIAN pin
during start-up with the output capacitance fully discharged.
Presence of reverse current is possible for CCM (high-power
inductance >3 mH) at certain conditions for limited input
capacitance (VOUT = VBULK_MIN every input half-line AC cycle).
Using a current probe, check if negative current is measured
either by increase input capacitance, reduce inductance or
place an ultrafast diode in series with the Drain node.
5. Follow the design procedure in AN-60 for the optimum line
regulation.
6. Power factor can be optimized by adjusting the conduction
time of the bridge rectifier. Refer to AN-60 for more details.
In a LYTSwitch-0 design using a buck or buck-boost converter
topology, the SOURCE pin is a switching node. Oscilloscope
measurements should therefore be made with probe grounded
to a DC voltage, such as primary return or DC input rail, and not
to the SOURCE pins. The power supply input must always be
supplied from an isolated source (e.g. via an isolation transformer).
8
Rev. B 06/15
www.power.com
LYT0002/0004-0006
Absolute Maximum Ratings(1,5)
DRAIN Pin Voltage............................................... -0.3 V to 700 V
Peak DRAIN Pin Current (LYT0002)............... 200 mA (375 mA)(2)
Peak DRAIN Pin Current (LYT0004)............... 400 mA (750 mA)(2)
Peak DRAIN Pin Current (LYT0005)............. 800 mA (1500 mA)(2)
Peak DRAIN Pin Current (LYT0006)........... 1400 mA (2600 mA)(2)
FEEDBACK Pin Voltage........................................... -0.3 V to 9 V
FEEDBACK Pin Current.................................................. 100 mA
BYPASS Pin Voltage................................................ -0.3 V to 9 V
Storage Temperature....................................... -65 °C to 150 °C
Operating Junction Temperature(3).................... -40 °C to 150 °C
Lead Temperature(4)..........................................................260 °C
Notes:
1. All voltages referenced to SOURCE, TA = 25 °C.
2. The higher peak DRAIN current is allowed if the DRAIN
to SOURCE voltage does not exceed 400 V.
3. Normally limited by internal circuitry.
4. 1/16 in. from case for 5 seconds.
5. Maximum ratings specified may be applied, one at a time,
without causing permanent damage to the product.
Exposure to Absolute Maximum Rating conditions for
extended periods of time may affect product reliability.
Thermal Resistance
Thermal Resistance: P Package:
(qJA) .................................70 °C/W(3); 60 °C/W(4)
(qJC)(1) ..................................................11 °C/W
D Package:
(qJA) ...............................100 °C/W(3); 80 °C/W(4)
(qJC)(2)...................................................30 °C/W
Parameter
Symbol
Notes:
1. Measured on pin 2 (SOURCE) close to plastic interface.
2. Measured on pin 8 (SOURCE) close to plastic interface.
3. Soldered to 0.36 sq. in. (232 mm2), 2 oz. (610 g/m2) copper clad.
4. Soldered to 1 sq. in. (645 mm2), 2 oz. (610 g/m2) copper clad.
Conditions
SOURCE = 0 V; TJ = -40 to 125 °C
See Figure 8
(Unless Otherwise Specified)
Min
Typ
Max
62
66
70
Units
Control Functions
Output
Frequency
Maximum Duty Cycle
fOSC
Average
TJ = 25 °C
Peak-Peak Jitter
4
kHz
DCMAX
S2 Open
66
69
72
%
FEEDBACK Pin Turnoff
Threshold Current
IFB
TJ = 25 °C
30
49
68
mA
FEEDBACK Pin Voltage
at Turnoff Threshold
VFB
1.54
1.65
1.76
V
130
220
mA
LYT0002
165
260
LYT0004
173
280
LYT0005
190
310
LYT0006
226
330
IS1
DRAIN Pin
Supply Current
IS2
VFB ≥2 V
(MOSFET Not Switching)
See Note A
FEEDBACK Open
(MOSFET
Switching)
See Notes A, B
mA
9
www.power.com
Rev. B 06/15
LYT0002/0004-0006
Parameter
Symbol
Conditions
SOURCE = 0 V; TJ = -40 to 125 °C
See Figure 8
(Unless Otherwise Specified)
Min
Typ
Max
LYT0002/0004
-5.5
-3.35
-1.8
LYT0005-0006
-7.5
-4.6
-2.5
LYT0002/0004
-3.8
-2.3
-1.0
LYT0005-0006
-4.5
-3.3
-1.5
Units
Control Functions (cont.)
ICH1
VBP = 0 V
TJ = 25 °C
See Note C
ICH2
VBP = 4 V
TJ = 25 °C
See Note C
BYPASS Pin
Charge Current
mA
BYPASS Pin
Voltage
VBP
5.55
5.8
6.10
V
BYPASS Pin
Voltage Hysteresis
VBPH
0.8
0.95
1.2
V
BYPASS Pin
Supply Current
IBPSC
See Note D
mA
68
Circuit Protection
di/dt = 55 mA/ms
TJ = 25 °C
126
136
146
145
165
185
195
210
225
222
265
282
240
257
275
271
310
345
350
375
401
396
450
504
LYT0002/0004
280
360
475
LYT0005
360
460
610
LYT0006
400
500
675
170
215
135
142
LYT0002
di/dt = 250 mA/ms
TJ = 25 °C
di/dt = 65 mA/ms
TJ = 25 °C
Current Limit
ILIMIT
(See Note E)
LYT0004
di/dt = 415 mA/ms
TJ = 25 °C
mA
di/dt = 75 mA/ms
TJ = 25 °C
LYT0005
di/dt = 500 mA/ms
TJ = 25 °C
di/dt = 95 mA/ms
TJ = 25 °C
LYT0006
di/dt = 610 mA/ms
TJ = 25 °C
Minimum On Time
tON(MIN)
Leading Edge
Blanking Time
tLEB
Thermal Shutdown
Temperature
TSD
Thermal Shutdown
Hysteresis
TSHD
TJ = 25 °C
See Note F
See Note G
75
ns
ns
150
°C
°C
10
Rev. B 06/15
www.power.com
LYT0002/0004-0006
Parameter
Symbol
Conditions
SOURCE = 0 V; TJ = -40 to 125 °C
See Figure 8
(Unless Otherwise Specified)
Min
Typ
Max
TJ = 25 °C
42
55.2
TJ = 100 °C
67
88.4
TJ = 25 °C
21
27.6
TJ = 100 °C
40
44.2
TJ = 25 °C
11
13.8
TJ = 100 °C
19
22.1
TJ = 25 °C
6
8.1
TJ = 100 °C
11
12.9
Units
Output
LYT0002
ID = 13 mA
ON-State
Resistance
RDS(ON)
LYT0004
ID = 25 mA
LYT0005
ID = 35 mA
LYT0006
ID = 45 mA
OFF-State Drain
Leakage Current
Breakdown Voltage
IDSS
VBP = 6.2 V,
VFB ≥2 V,
VDS = 560 V,
TJ = 25 °C
tR
Fall Time
tF
50
LYT0004
60
LYT0005
75
LYT0006
90
VBP = 6.2 V, VFB ≥2 V,
TJ = 25 °C
BVDSS
Rise Time
LYT0002
700
Measured in a Typical Buck
Converter Application
DRAIN Supply Voltage
tEN
Output Disable
Setup Time
tDST
Auto-Restart
ON-Time
tAR
50
ns
50
ns
Auto-Restart
Duty Cycle
DCAR
V
See Figure 10
10
0.5
TJ = 25 °C
See Note H
mA
V
50
Output Enable Delay
W
LYT0002
Not Applicable
LYT0004-0006
50
LYT0002
Not Applicable
LYT0004-0006
6
ms
ms
ms
%
NOTES:
A. Total current consumption is the sum of IS1 and IDSS when FEEDBACK pin voltage is ≥2 V (MOSFET not switching) and the sum of
IS2 and IDSS when FEEDBACK pin is shorted to SOURCE (MOSFET switching).
B Since the output power MOSFET is switching, it is difficult to isolate the switching current from the supply current at the DRAIN.
An alternative is to measure the BYPASS pin current at 6 V.
C. See Typical Performance Characteristics section Figure 15 for BYPASS pin start-up charging waveform.
D. This current is only intended to supply an optional optocoupler connected between the BYPASS and FEEDBACK pins and not
any other external circuitry.
E. For current limit at other di/dt values, refer to Figure 14.
F. This parameter is guaranteed by design.
G. This parameter is derived from characterization.
H. Auto-restart on time has the same temperature characteristics as the oscillator (inversely proportional to frequency).
11
www.power.com
Rev. B 06/15
LYT0002/0004-0006
470 Ω
5W
S1
470 kΩ
D
FB
S2
BP
50 V
S
S
S
S
50 V
0.1 µF
PI-3490-060204
Figure 8. LYTSwitch-0 General Test Circuit.
DCMAX
(internal signal)
tP
FB
VDRAIN
t =
P
tEN
1
fOSC
PI-3707-112503
Figure 9.
LYTSwitch-0 Duty Cycle Measurement.
Figure 10. LYTSwitch-0 Output Enable Timing.
12
Rev. B 06/15
www.power.com
LYT0002/0004-0006
Typical Performance Characteristics
1.0
PI-2680-012301
1.2
Output Frequency
(Normalized to 25 °C)
Breakdown Voltage
(Normalized to 25 °C)
PI-2213-012301
1.1
1.0
0.8
0.6
0.4
0.2
0
0
25
50
-50 -25
75 100 125 150
1.0
0.8
Normalized di/dt
di/dt = 1
di/dt = 6
0.4
0.2
100
1.2
1.0
0.8
0.6
LYT0002
LYT0004
LYT0005
LYT0006
0.4
0.2
1
2
3
6
5
4
3
2
1
0
0.6
Time (ms)
Figure 15. BYPASS Pin Start-up Waveform.
5
400
350
25 °C
300
6
100 °C
250
200
Scaling Factors:
LYT0002 0.5
LYT0004 1.0
LYT0005 2.0
LYT0006 3.4
150
100
50
0.4
4
Figure 14. Current Limit vs. di/dt.
Drain Current (mA)
PI-2240-012301
7
0.2
Normalized
Current
Limit = 1
136 mA
210 mA
257 mA
450 mA
Normalized di/dt
Figure 13. Current Limit vs. Temperature at Normalized di/dt.
BYPASS Pin Voltage (V)
Normalized
di/dt = 1
55 mA/µs
65 mA/µs
75 mA/µs
95 mA/µs
0
150
Temperature (°C)
0
100 125
PI-6812-061213
Current Limit
(Normalized to 25 °C)
1.2
50
75
1.4
Normalized Current Limit
PI-3709-111203
1.4
0
50
Figure 12. Frequency vs. Temperature.
Figure 11. Breakdown vs. Temperature.
0
-50
25
Junction Temperature ( °C)
Junction Temperature (°C)
0.6
0
0.8
1.0
PI-6813-061213
0.9
-50 -25
0
0
2
4
6
8 10 12 14 16 18 20
Drain Voltage (V)
Figure 16. Output Characteristics.
13
www.power.com
Rev. B 06/15
LYT0002/0004-0006
Typical Performance Characteristics (cont.)
PI-6814-061213
Drain Capacitance (pF)
1000
100
Scaling Factors:
LYT0002
LYT0004
LYT0005
LYT0006
10
0.5
1.0
2.0
3.4
1
0
100
200
300
400
500
600
Drain Voltage (V)
Figure 17. COSS vs. Drain Voltage.
14
Rev. B 06/15
www.power.com
LYT0002/0004-0006
PDIP-8B (P Package)
⊕D S
.004 (.10)
.137 (3.48)
MINIMUM
-E-
.240 (6.10)
.260 (6.60)
Pin 1
-D-
.367 (9.32)
.387 (9.83)
Notes:
1. Package dimensions conform to JEDEC specification
MS-001-AB (Issue B 7/85) for standard dual-in-line (DIP)
package with .300 inch row spacing.
2. Controlling dimensions are inches. Millimeter sizes are
shown in parentheses.
3. Dimensions shown do not include mold flash or other
protrusions. Mold flash or protrusions shall not exceed
.006 (.15) on any side.
4. Pin locations start with Pin 1, and continue counter-clockwise to Pin 8 when viewed from the top. The notch and/or
dimple are aids in locating Pin 1. Pin 6 is omitted.
5. Minimum metal to metal spacing at the package body for
the omitted lead location is .137 inch (3.48 mm).
6. Lead width measured at package body.
7. Lead spacing measured with the leads constrained to be
perpendicular to plane T.
.057 (1.45)
.068 (1.73)
(NOTE 6)
.125 (3.18)
.145 (3.68)
.015 (.38)
MINIMUM
-TSEATING
PLANE
.120 (3.05)
.140 (3.56)
.100 (2.54) BSC
.014 (.36)
.022 (.56)
.048 (1.22)
.053 (1.35)
⊕T E D S
.010 (.25) M
.008 (.20)
.015 (.38)
.300 (7.62) BSC
(NOTE 7)
.300 (7.62)
.390 (9.91)
P08B
PI-2551-040110
15
www.power.com
Rev. B 06/15
LYT0002/0004-0006
SO-8C (D Package)
4
B
0.10 (0.004) C A-B 2X
2
DETAIL A
4.90 (0.193) BSC
A
4
8
D
5
2 3.90 (0.154) BSC
GAUGE
PLANE
SEATING
PLANE
6.00 (0.236) BSC
0-8
C
1.04 (0.041) REF
2X
0.10 (0.004) C D
1
Pin 1 ID
4
1.35 (0.053)
1.75 (0.069)
0.25 (0.010)
BSC
0.40 (0.016)
1.27 (0.050)
0.20 (0.008) C
2X
7X 0.31 - 0.51 (0.012 - 0.020)
0.25 (0.010) M C A-B D
1.27 (0.050) BSC
o
1.25 - 1.65
(0.049 - 0.065)
DETAIL A
0.10 (0.004)
0.25 (0.010)
7X
0.10 (0.004) C
H
SEATING PLANE
0.17 (0.007)
0.25 (0.010)
C
Reference
Solder Pad
Dimensions
+
Notes:
1. JEDEC reference: MS-012.
2.00 (0.079)
+
D07C
1.27 (0.050)
2. Package outline exclusive of mold flash and metal burr.
3. Package outline inclusive of plating thickness.
4. Datums A and B to be determined at datum plane H.
5. Controlling dimensions are in millimeters. Inch dimensions
are shown in parenthesis. Angles in degrees.
4.90 (0.193)
+
+
0.60 (0.024)
PI-4526-040110
Part Ordering Information
• LYTSwitch-0 Product Family
• LYT Series Number
• Package Identifier
P
Plastic PDIP-8B
D
Plastic SO-8C
• Tape & Reel and Other Options
Blank
TL
LYT 0002 D - TL
Standard Configurations
Tape & Reel, 2.5 k pcs minimum for D Package.
Not available for P Package.
16
Rev. B 06/15
www.power.com
LYT0002/0004-0006
Notes
17
www.power.com
Rev. B 06/15
Revision
Notes
Date
A
Initial Release
06/13
B
Updated with new Brand Style Logo.
06/15
For the latest updates, visit our website: www.power.com
Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power
Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES
NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
Patent Information
The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered
by one or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations.
A complete list of Power Integrations patents may be found at www.power.com. Power Integrations grants its customers a license under
certain patent rights as set forth at http://www.power.com/ip.htm.
Life Support Policy
POWER INTEGRATIONS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein:
1. A Life support device or system is one which, (i) is intended for surgical implant into the body, or (ii) supports or sustains life, and (iii)
whose failure to perform, when properly used in accordance with instructions for use, can be reasonably expected to result in significant
injury or death to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause
the failure of the life support device or system, or to affect its safety or effectiveness.
The PI logo, TOPSwitch, TinySwitch, LinkSwitch, LYTSwitch, InnoSwitch, DPA-Switch, PeakSwitch, CAPZero, SENZero, LinkZero,
HiperPFS, HiperTFS, HiperLCS, Qspeed, EcoSmart, Clampless, E-Shield, Filterfuse, FluxLink, StakFET, PI Expert and PI FACTS are
trademarks of Power Integrations, Inc. Other trademarks are property of their respective companies. ©2015, Power Integrations, Inc.
Power Integrations Worldwide Sales Support Locations
World Headquarters
5245 Hellyer Avenue
San Jose, CA 95138, USA.
Main: +1-408-414-9200
Customer Service:
Phone: +1-408-414-9665
Fax: +1-408-414-9765
e-mail: usasales@power.com
China (Shanghai)
Rm 1601/1610, Tower 1,
Kerry Everbright City
No. 218 Tianmu Road West,
Shanghai, P.R.C. 200070
Phone: +86-21-6354-6323
Fax: +86-21-6354-6325
e-mail: chinasales@power.com
China (Shenzhen)
17/F, Hivac Building, No. 2,
Keji Nan 8th Road, Nanshan
District, Shenzhen, China,
518057
Phone: +86-755-8672-8689
Fax: +86-755-8672-8690
e-mail: chinasales@power.com
Germany
Lindwurmstrasse 114
80337 Munich
Germany
Phone: +49-895-527-39110
Fax: +49-895-527-39200
e-mail: eurosales@power.com
India
#1, 14th Main Road
Vasanthanagar
Bangalore-560052 India
Phone: +91-80-4113-8020
Fax: +91-80-4113-8023
e-mail: indiasales@power.com
Italy
Via Milanese 20, 3rd. Fl.
20099 Sesto San Giovanni (MI)
Italy
Phone: +39-024-550-8701
Fax: +39-028-928-6009
e-mail: eurosales@power.com
Japan
Kosei Dai-3 Bldg.
2-12-11, Shin-Yokohama,
Kohoku-ku
Yokohama-shi Kanagwan
222-0033 Japan
Phone: +81-45-471-1021
Fax: +81-45-471-3717
e-mail: japansales@power.com
Korea
RM 602, 6FL
Korea City Air Terminal B/D, 159-6
Samsung-Dong, Kangnam-Gu,
Seoul, 135-728, Korea
Phone: +82-2-2016-6610
Fax: +82-2-2016-6630
e-mail: koreasales@power.com
Singapore
51 Newton Road
#19-01/05 Goldhill Plaza
Singapore, 308900
Phone: +65-6358-2160
Fax: +65-6358-2015
e-mail: singaporesales@power.com
Taiwan
5F, No. 318, Nei Hu Rd., Sec. 1
Nei Hu Dist.
Taipei 11493, Taiwan R.O.C.
Phone: +886-2-2659-4570
Fax: +886-2-2659-4550
e-mail: taiwansales@power.com
UK
First Floor, Unit 15, Meadway
Court, Rutherford Close,
Stevenage, Herts. SG1 2EF
United Kingdom
Phone: +44 (0) 1252-730-141
Fax: +44 (0) 1252-727-689
e-mail: eurosales@power.com
工商网监
湘ICP备2023018690号
