0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
587B302LP

587B302LP

  • 厂商:

    PROTEC(普罗太克)

  • 封装:

  • 描述:

    587B302LP - low profile 240v acpower line surge suppressor - Protek Devices

  • 数据手册
  • 价格&库存
587B302LP 数据手册
05057 Only One Name Means ProTek’Tion™ 587B062LP - 587B302LP Low PRofiLe 240v ac PoweR Line suRge suPPRessoR DescRiPtion The 587BxxxLP Series of 240 Volt AC Surge Suppressors is designed for use by the OEM, equipment installer and or maintenance contractor. These modules employ a three stage technology proven to be the most cost effective and reliable method in protecting sensitive electronic equipment from over voltage transients. This series is designed to protect AC powered equipment from the 6,000 volt peak open circuit voltage and 3,000 Amp short circuit current as defined in ANSI/IEEE C62.41, Category C1. The 587BxxxLP Series offers a high degree of protection against 240 VAC EMI line noise. It is ideal for protecting 800 Volt components because the solid state TVS technology assures that the line-to-neutral voltage will not exceed 800 Volts. While the modules are designed for transient voltage protection, the advanced circuitry will also attenuate the amplitude and slow the rate of rise of high frequency noise acting as an EMI filter. The 587BxxxLP Series includes differential mode protection, which is effective in reducing interference from line to equipment and are effective in reducing equipment generated noise to meet FCC, VDE and CSA interference requirements. Low PRofiLe featuRes aPPLications • Hard Wired Equipment AC Power Protection • Load Side Distribution Systems • Secondary Protection for Light Industrail AC Power • Compatible with IEC 61000-4-5 (Surge): 1kA, 8/20µs, Level 4 (LineGnd) & 333A, Level 4 (Line-Line) • Meets ANSI/IEEE C62.41 Requirements • Listed to CSA, File LR65240 • Differential and Common Mode Protection • Low Clamping Voltage • Nanosecond Response Time • Long Life and Maintenance Free • Finger Safe Connections MechanicaL chaRacteRistics • Low Profile Plastic Package • Approximate Weight: 360 grams • Flammability Rating UL 94V-0 figuRe 1 tRansient voLtage thReat conDition 8 6 Kilovolts 4 2 0 Kilovolts 6 4 2 0 figuRe 2 tyPicaL cLaMPing action of a 15a MoDuLe 0 10 20 30 40 50 60 0 10 20 30 40 50 60 t - time - µs t - time - µs Figures 1 and 2 are photographs of digitized waveforms showing the typical clamping action of a 15A module. A 12 Ohm resistor is used to represent a 10A equipment load. The load is then subjected to the ANSI/IEEE C62.41 Catagory CI test conditions (6000V/3000A). These photographes contrast the effect on equipment with and without the protector. 05057.R5 2/11 Page 1 www.protekdevices.com 05057 Only One Name Means ProTek’Tion™ 587B062LP - 587B302LP tyPicaL Device chaRacteRistics MaXiMuM Ratings @ 25°c unless otherwise specified PaRaMeteR Operating Line Voltage: +10% Line Current: 587B062LP/587B102LP/587B162LP/587B302LP Peak Transient Voltage Peak Transient Current Current Leakage @ 240 Volts AC: Line-to-Neutral, Neutral-to-Ground, Line-to-Ground Operating Temperature - Note 1 Storage Temperature - Note 1 1. Measured at the center of the mounting surface. syMBoL VO TA TSTG vaLue 240 6/10/16/30 6000 3000 1 -40 to 85 -40 to 85 units Volts AC Amps Volts Amps mA °C °C notes eLectRicaL chaRacteRistics @ 25°c unless otherwise specified PRotection MoDe (note 1) MaXiMuM cLaMPing voLtage (note 2) voLts Line to Neutral Neutral to Ground Line to Ground notes 800 1000 1000 oPen ciRcuit voLtage (note 2) @1.2/50µs voLts 6000 6000 6000 shoRt ciRcuit cuRRent (note 2) @ 8/20µs aMPs 3000 3000 3000 1. Differential Mode Protection: Line to Neutral. Common Mode Protection: Line to Ground & Neutral to Ground. 2. Test condition responses to transient voltages. aRRestoR Definitions Clamping Voltage: The clamping voltage of an arrester is the voltage that appears across its terminals during conduction of a transient current. Standard Wave Form: The waveform of a surge current or voltage is designated by a combination of two numbers. The first number is for the time of the wave front expressed in microseconds from zero to the peak of the wave. The second number is for the time of the wavetail also expressed in microseconds from zero to the instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 µs waveform. Transient Current: The transient current of an arrestor is the peak surge current which flows through the arrester when voltage clamping occurs. oPeRation For maximum effectiveness, the protector should be installed directly after the AC line on/off switch and fuse. This will protect the electronics from the AC line switch arcing and the severe transients caused by a fuse clearing. Some heat is produced when operating at full current load, and heat sinking may be required to maintain case temperature below 85°C. The case temperature is measured at the center of the mounting surface. The unit should not be mounted to a low combusting temperature material such as wood. High energy transients will cause a large circulating current in the AC input line (2,500A is possible). To prevent electromagnetic coupling, the AC line on the input side of the protector must be dressed away from other wiring, magnetic shielding may be required. In addition, the electrical service must be connected to a low impedance earth ground. 05057.R5 2/11 Page 2 www.protekdevices.com 05057 Only One Name Means ProTek’Tion™ 587B062LP - 587B302LP PacKage infoRMation outLine DiMensions DiM A B C D E F G 58.04 43.89 27.9 58.80 2.29 110.92 14.43 44.39 1.62 1.10 2.32 MiLLiMeteRs Min 96.8 88.9 111.68 4.37 inches Min 3.81 3.50 4.40 0.586 1.72 MaX MaX A E D C B F G Line 1 Out Line In Dia. 0.181” Neutral In Ground In DEVICE MARKING Line 2 Out Neutral 1 Out Neutral 2 Out Ground Out oRDeRing infoRMation Base PaRt nuMBeR (xx = voltage) 587BxxxLP MaRKing Part Number, Date Code, Voltage, Logo, Current Rating, CSA Logo 05057.R5 2/11 Page 3 www.protekdevices.com 05057 Only One Name Means ProTek’Tion™ 587B062LP - 587B302LP coMPany infoRMation coMPany PRofiLe ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), inductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide application specific protection solutions for all electronic equipment/systems. ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products. contact us corporate headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By telephone General: 602-431-8101 Sales: 602-414-5109 Customer Service: 602-414-5114 By fax General: 602-431-2288 By e-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com web www.protekdevices.com www.protekanalog.com COPYRIGHT © ProTek Devices 1998 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. PATENT INFORMATION: This device is patented under U.S. Patent No. 4,563,720 05057.R5 2/11 Page 4 www.protekdevices.com
587B302LP 价格&库存

很抱歉,暂时无法提供与“587B302LP”相匹配的价格&库存,您可以联系我们找货

免费人工找货