PAM22LOPR2268-T7

95006 ANALOG PRODUCTS DIVISION Features           CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.6Ω. Vcc Range: 1.8V to 4.2V Rail-to-Rail Signal Range High Off Isolation: -75dB @ 100kHz Crosstalk Rejection: -90dB @ 100kHz Break-Before-Make Switching Extended Industrial Temperature Range: –40°C to 85°C LoPro© Packaging (Pb-free): 10-Lead Micro Package QFN-10Lead Micro Package PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ Description ProTek Analog’s PAM22LOPR2268 is a dual high-bandwidth, fast single-pole double throw (SPDT) CMOS switch. It can be used as an analog switch or as a low-delay bus switch. Specified over a operating power supply voltage, 1.8V to 4.2V, the PAM22LOPR2268 has an On-Resistance of 0.6Ω at +2.7V. Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. Functional Block Diagram Applications            Cell Phones PDAs MP3 players Portable Instrumentation Computer Peripherals Speaker Headset Switching Power Routing Relay Replacement Audio and Video Signal Routing PCMCIA Cards Modems NC1 NO1 NC2 NO2 COM1 IN1 COM2 IN2 Fig. 1 PAM22LOPR2268 Pin Descriptions Pin No. 1,3 4 10,2 8,5 9 7,6 Name NOX GND NCX COMX VCC INX Description DATA Port (Normally Open) IN1 IN2 Pin Configuration (Top View) Ground DATA Port (Normally Closed) Common Port / DATA Port Positive Power Supply Logic Control NC1 10 1 2 3 NO2 COM1 8 7 6 5 COM2 VDD 9 4 GND NO1 NC2 Ordering Information Logic Function Table Logic Input (INX) 0 1 Function NCX Connected to COMX NOX Connected to COMX Temp Range -40 to 85 °C -40 to 85 °C Package QFN-10 10 Lead LoPro Part Number PAM22LOPR2268QT7 PAM22LOPR2268-T7 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 1 ANALOG PRODUCTS DIVISION Absolute Maximum Ratings (1) PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ Recommended Operating Conditions Supply Voltage VCC ....................................................4.5V (2) DC Switch Voltage (VS) ....................................VCC +0.5V DC Input Voltage (VIN)(2) .............................................4.5V Analog Signal Range.....................Min -1.0 to Max VCC +1.0 Continuous Current NO_NC_COM_ ...............±300mA Peak Current NO_NC_COM_ (pulsed at 1ms 50% duty cycle) ....................±400mA Peak Current NO_NC_COM_ (pulsed at 1ms 10% duty cycle) ........................... ±500mA Storage Temperature Range (TSTG) .. …..–65°C to +150°C Junction Temperature under Bias (TJ)..........................150°C Junction Lead Temperature (TL) (Soldering, 10 seconds).............................................260°C Power Dissipation (PD) @ +85°C ........................ …250mW (3) Supply Voltage Operating (VCC) ………………………1.8V to 4.2V Control Input Voltage (VIN)……………….. 0V to VCC Switch Input Voltage (VIN)…………………………. -0.3V to VCC Output Voltage (VOUT)……………………………………………………… 0V to VCC Operating Temperature (TA)………………………... –40°C to +85°C Input Rise and Fall Time (tr,tf) Control Input VCC = 2.3V - 3.6V………………..0ns/V to 10ns/V Thermal Resistance (θJA)………………………………….350°C/W Lead Temperature (soldering 10s)……………………… .+240°C Bump Temperature (soldering notes) Infrared (15s) ……………………………………………..….+220°C Vapor Phase (60ns)………………………………………….+215°C Notes: 1. "Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. 3. Control input must be held HIGH or LOW; it must not float. 4. Internal Resistance RTERM is guaranteed by design and not production tested. Capacitance Parameter NC Off Capacitance NO Off Capacitance NC On Capacitance NO On Capacitance Symbol CNC(OFF) CNO(OFF) CNC(ON) CNO(ON) Test Conditions f =1MHz, See Test Circuit Figure7. f =1MHz, See Test Circuit Figure7. f =1MHz, See Test Circuit Figure8. f =1MHz, See Test Circuit Figure8. Min Typ 35 35 pF 95 95 Max Unit 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 2 ANALOG PRODUCTS DIVISION DC Electrical Characteristics +3V Supply PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ (VCC = 2.7V to 3.3V, TA = –40°C to 85°C, unless otherwise noted. Typical values are at 3V and +25°C.) Parameter Analog Switch Analog Signal Range NC On-Resistance NO On-Resistance On-Resistance Match Between Channels NC On-Resistance Flatness NO On-Resistance Flatness Internal Termination Resistors NO or NC Off Leakage Current COM On Leakage Current Digital I/O Input Logic High Input Logic Low Input Hysteresis IN Input Leakage Current Supply Current Symbol VNO,VNC, VCOM RON(NC) RON(No) ∆RON RONF(NC) RONF(NO) RTERM IOFF(NO) or IOFF(NC) ICOM(ON) Test Conditions Min Typ Max Unit -0.3 VCC = 2.7V, ICOM = 100mA, VNC = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO or VNC = 1.5V VCC = 2.7V, ICOM = 100mA, VNC = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO = 0 to VCC 200 VCC = 3.3V, ICOM, VNO or VNC = 3.0V, 0.3V VCOM = 0.3V,3.0V VCC = 3.3V, ICOM, VNO or VNC = 3.0V, 0.3V VCOM = 0.3V,3.0V or Floating -2 0 -2 0 0 .4 0 .4 0.01 VCC 0 .6 0 .6 0.05 0.2 0.2 V Ω Ω 20 nA 20 VIH VIL VH IIN ICC VCC = 3.3V VIN = 0 or VCC VCC = 3.6V, VIN = 0 or VCC 1.3 V 0.5 300 -0.5 0.9 0.5 1.2 mV µA nA Switch and AC Characteristics Parameter Symbol Test Conditions Turn-On Time Turn-Off Time Break-BeforeMake Delay Charge Injection Off-Isolation Crosstalk tON tOFF tBBM Q QIRR XTALK VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. See Test Circuit Figure 1 & 2 Min Typ 15 4 Max 25 10 20 Unit VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. See Test Circuit Figure 1 & 2 nS VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. See Test Circuit Figure 3 COM = 0, RS = 0, CL = 1nF. VGEN = 0 See Test Circuit Figure 4 55 -75 pC CL = 5pF, RL = 50Ω, f = 100kHz, VCOM = 1VRMS See Test Circuit Figure 5 CL = 5pF, RL = 50Ω, f = 100kHz, VCOM = 1VRMS See Test Circuit Figure 6 dB -90 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 3 ANALOG PRODUCTS DIVISION 3dB Bandwidth f3dB See Test Circuit Figure 9 PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ 100 MHz Typical Characteristics NO RDSON 2.0 1.8 1.6 2.7Volt NC RDSON 2.0 1.8 1.6 2.7Volt RDS (OHMS) ON RDS (OHMS) ON 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0 1.0 2.0 V COM (Volts) 3.0 3.3Volt 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0 1.0 2.0 V COM (Volts) 3.0 3.3Volt NO RON vs V COM (Tem p) 3.0 3.0 NC RON vs V COM (Tem p) 2.5 +85°C 2.5 +85°C 2.0 2.0 RON (OHMS) +25°C 1.5 RON (OHMS) 1.5 +25°C 1.0 -40°C 1.0 -40°C 0.5 0.5 0.0 0.0 1.0 2.0 V COM (Volts) 3.0 0.0 0.0 1.0 2.0 V COM (Volts) 3.0 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 4 ANALOG PRODUCTS DIVISION VDD vs IDD 1000 900 800 PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ Supply Current (pA) 700 600 500 400 300 200 100 0 0.0 1.0 2.0 3.0 Supply Voltage V DD (Volts) Note: Characteristics are guaranteed by design and are not production tested. Test Circuits and Timing Diagrams VCC VIN NC or NO IN COM VOUT RL 50Ω GND CL 35pF Logic Input CL includes fixture and stray capacitance Figure 1. AC Test Circuit Note1. Unused Input (NO or NC) must be grounded VIH Logic Input V IL tr < 5nS Off 50% On Off tf < 5nS tOFF Switch Output 90% 0V tON 90% Logic Input Waveforms inverted for Switches that have opposite logic Figure2 AC Waveforms 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 5 ANALOG PRODUCTS DIVISION PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ VIN NC COM NO IN CL 35pF VOUT Logic Input VOUT 0.9 x VOUT tBBM 50% RL 50Ω GND Logic Input Figure 3. Break Before Make Interval Timing RGEN NC or NO COM VOUT Logic Off Input On Off VGEN IN CL 1nF ∆VOUT Q= (∆VOUT)(CL) GND Logic Input Figure 4. Charge Injection Test VCC 10nF 50Ω COM 50Ω VCC 10nF NC COM Signal Generator NO / NC GND Analyzer CL 5pF RL 50Ω IN Logic Input 0V or VIH Signal Generator NO GND Analyzer CL 5pF RL 50Ω IN 50Ω 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 6 ANALOG PRODUCTS DIVISION Figure 5. Off Isolation VCC 10nF PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ Figure 6. Crosstalk VCC 10nF COM Capacitance Meter Logic Input 0V or VIH f = 1MHz COM Capacitance Meter f = 1MHz NO / NC GND IN IN NO / NC GND Logic Input 0V or VIH Figure 7. Channel Off Capacitance Figure 8. Channel On Capacitance VCC 10nF 50Ω NC / NO COM Signal Generator Logic Input 0V or VIH 50Ω GND Analyzer IN Figure 9. Bandwidth 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 7 ANALOG PRODUCTS DIVISION Package Layout and Dimensions Top View E Bottom View D PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ DIM A B C MIN 1.25 1.55 0.50 TYP 1.30 1.60 0.55 0.40 0.29 0.49 0.30 0.50 0.80 REF 0.00 - 0.05 0.10 REF 0.15 0.59 0.20 0.60 0.25 0.61 0.31 0.51 Max 1.35 1.65 0.60 A D G E F Pin 1 Area g B F G f c c1 Front View f g Note: Package Dimensions in millimeters C Recommended Land Pattern c1 0.25 0.50 0.75 0.70 1.60 0.40 1.90 Tape and Reel Specifications Reel Dia 178 (7”) A0 1.47±0.05 B0 1.73±0.05 K0 0.65±0.05 D 1.50±0.10 E 1.75±0.10 F 3.50±0.05 P0 W 12.00±0.30 P0 4.00±0.10 P2 2.00±0.05 P 4.00±0.10 t-max 0.25 t D P2 10 Pitches Cumulative Tolerance on Tape± 0.2 E Top cover tape Pin 1 indicated by Dot A0 K0 68T 68T F W 68T B0 P 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 8 ANALOG PRODUCTS DIVISION Package Layout and Dimensions QFN-10 Top View E Bottom View D PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ DIM A B C MIN 1.35 1.75 0.50 TYP 1.40 1.80 0.55 0.40 0.39 0.40 0.80 REF 0.10 REF 0.15 0.49 0.20 0.25 0.41 Max 1.45 1.85 0.60 A g Pin 1 Area f D G E G c1 B f g Front View Note: Package Dimensions in millimeters C Recommended Land Pattern c1 0.25 0.50 0.6 1.50 0.40 1.90 Tape and Reel Specifications Reel Dia 178 (7”) A0 1.47±0.05 B0 1.83±0.05 K0 0.65±0.05 D 1.50±0.10 E 1.75±0.10 F 3.50±0.05 P0 W 12.00±0.30 P0 4.00±0.10 P2 2.00±0.05 P 4.00±0.10 t-max 0.25 t D P2 10 Pitches Cumulative Tolerance on Tape± 0.2 E Top cover tape Pin 1 indicated by Dot A0 K0 Q68 Q68 F W Q68 B0 P 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 9 ANALOG PRODUCTS DIVISION PAM22LOPR2268 LoPro Dual SPDT Analog Switch ™ Life Support Policy PROTEK ANALOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS W ITHOUT THE EXPRESS W RITTEN APPROVAL OF THE PRESIDENT OF PROTEK DEVICES. 2929 S Fair Lane, Tempe, AZ, 85282 Tel: (602) 431-8101. Fax: (602) 431-2288 www.protekdevices.com 95006 Rev0.01/12 NOT FOR USE IN LIFE SUPPORT SYSTEMS 10