05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
ThyRiSToR SuRge SuPPReSSoR DeSCRiPTion
The PP-SM Series are thyristor surge suppression (TSS) devices designed to protect telecommunication equipment against lightning and transients induced by AC power lines. These devices can be used on central office equipment, PBX, DSU, OCU and other telecommunication equiment/systems. The bidirectional configuration provides protection for both positive and negative transients and the discrete surface mount package allows for individual placement of the device on line cards or other locations where multiple component devices do not offer the versatile in board trace layout. This series can be used to provide protection in accordance with industry standards such as FCC Part 68, ANSI C62.41, UL 1459, GR-1089-CORE, IEC 61000-2, IEC 61000-4 and IEC 61000-4-5 requirements.
Do-214AA PACkAge FeATuReS
• Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV • Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns • Compatible with IEC 61000-4-5 (Surge): 95A, 8/20µs - L4(LineGround), 48A - L4(Line-Line) & 83A - L2(Power) • FCC Part 68, UL 1459, Bellcore 1089 & ITU-K.20/K.21 Compliant • UL File Recognition #E208219 • Peak Off-State Voltage from 25 to 300 Volts • Surge Current Capability (See Table 1) • ESD Protection > 25 kilovolts • Low Capacitance for T1/E1 Trunk & Line Card Applications • Bidirectional Configuration • RoHS Compliant • REACH Compliant
APPliCATionS
• • • • • • T1/E1 Trunk & Line Cards SLIC Line Card DBX Branch Exchange Switches FCC Part 68 Customer Premise Equipment Line Interface Modem xDSL Architecture Interface
meChAniCAl ChARACTeRiSTiCS
• • • • Molded Plastic DO-214AA Package Approximate Weight: 2.5 grams Lead-Free Pure-Tin Plating (Annealed) Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C • Flammability Rating UL 94V-0 • 12mm Tape and Reel per EIA Standard 481 DEVICE SYMBOL BIDIRECTIONAL
TAble 1 - SuRge RATingS
SeRieS i PP 2/10µs AmPS
150 300 500
i PP 8/20µs AmPS
150 300 400
i PP 10/160µs AmPS
100 150 200
i PP 10/560µs AmPS
50 100 200
i PP 10/1000µs AmPS
50 80 100
i TSm 60hz AmPS
20 32 60
di/dt A/µs (note 1)
500 500 500
dv/dt V/µs (note 1)
2000 2000 2000
SA SB SC noTeS
1. Critical rate of rise for On-State Current (di/dt) and Off-State Voltage (dv/dt).
05081.R11 2/11
Page 1
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
mAXimum RATingS @ 25°C unless otherwise Specified
PARAmeTeR
Surge Current - 50/60Hz (SC Series) Junction Temperature Storage Temperature Thermal Resistance (Junction) - SA & SB Series Thermal Resistance (Junction) - SC Series Thermal Resistance (Ambient) - SA & SB Series Thermal Resistance (Ambient) - SC Series
Symbol
ITSM TA TSTG RQJC RQJC RQJA RQJA
VAlue
60 -40 to 150 -55 to 150 28 26 90 85
uniTS
Amps °C °C °C/Watt °C/Watt °C/Watt °C/Watt
FiguRe 1 PulSe WAVeFoRm
tf
iPP - Peak Pulse Current - % of iPP 100
FiguRe 2 Vi ChARACTeRiSiTC CuRVe
TEST WAVEFORM PARAMETERS tf = 10µs td = 1000µs
IPP ITSM IT IS IH VS IDRM VT VDRM
Peak Value IPP td = t/(IPP/2)
50
e-t
0 0 1 t - Time - ms 2 3
100 non-Repetitive on-State Current (iTSm) - Amps
FiguRe 3 on-STATe CuRRenT VS SuRge CuRRenT DuRATion
PPxxxxSA PPxxxxSC
10
PPxxxxSB
1 1 10 100 Surge Current Duration - Full Cycles Supply Frequency - 60 hz Sinusoidal
Page 2
1000
05081.R11 2/11
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
eleCTRiCAl ChARACTeRiSTiCS PeR line @ 25°C unless otherwise Specified
PART numbeR DeViCe mARking RePeTiTiVe SWiTChing minimum SWiTChing mAXimum PeAk VolTAge holDing CuRRenT oFF-STATe CuRRenT CuRRenT oFF-STATe VolTAge (Fig. 7) (Fig. 4) @100V/µs di/dt = 1A/ms @V DRm V DRm VS ih iS i DRm VolTS VolTS mA mA µA
58 65 75 90 120 140 160 190 220 275 300 25 58 65 75 90 120 140 160 190 220 275 300 58 65 75 90 120 140 160 190 220 275 300 77 88 98 130 160 180 220 260 300 350 400 40 77 88 98 130 160 180 220 260 300 350 400 77 88 98 130 160 180 220 260 300 350 400 150 150 150 150 150 150 150 150 150 150 150 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
mAXimum on-STATe VolTAge (Fig. 5) @i T VT VolTS
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
on-STATe CuRRenT
TyPiCAl CAPACiTAnCe (note 1) @2V, 1mhz C pF
60 60 60 60 40 40 40 30 30 30 30 110 60 60 60 60 40 40 40 30 30 30 30 120 120 120 120 80 80 80 60 60 60 60
iT AmPS
2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2
PP0640SA PP0720SA PP0800SA PP1100SA PP1300SA PP1500SA PP1800SA PP2300SA PP2600SA PP3100SA PP3500SA PP0300SB PP0640SB PP0720SB PP0800SB PP1100SB PP1300SB PP1500SB PP1800SB PP2300SB PP2600SB PP3100SB PP3500SB PP0640SC PP0720SC PP0800SC PP1100SC PP1300SC PP1500SC PP1800SC PP2300SC PP2600SC PP3100SC PP3500SC
GC GD GE GF GG GH GI GJ GK GL GM GN GP GQ GR GS GT GU GV GW GX GY GZ HC HD HE HF HG HH HI HJ HK HL HM
1. Capacitance imblance between positive and negative polarities is typically < 15pF. 05081.R11 2/11 Page 3 www.protekdevices.com
noTeS
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TyPiCAl DeViCe ChARACTeRiSTiCS
FiguRe 4 TyPiCAl PeAk oFF-STATe CuRRenT VS junCTion TemPeRATuRe FiguRe 5 TyPiCAl PeAk on-STATe CuRRenT VS on-STATe VolTAge
10 iDRm - Peak off-State Current - µA
100
1
iT - on-State Current - A 0 40 80 tA - Temperature - °C 120
10
0.1
0.01 -40
1
0
1
2
3 4 5 VT - on-State Voltage - V
6
7
FiguRe 6 TyPiCAl noRmAlizeD SWiTChing VolTAge VS junCTion TemPeRATuRe
1.10 normalized VS normalized ih
FiguRe 7 TyPiCAl noRmAlizeD holDing CuRRenT VS junCTion TemPeRATuRe
2
1
1
0.9
0.8 -40
0
40 80 tA - Temperature - °C
120
0 -40
0
40 80 tA - Temperature - °C
120
05081.R11 2/11
Page 4
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
APPliCATion inFoRmATion FiguRe 1 - ul 1459 & FCC PART 68 meTAlliC PRoTeCTion
The TSS (Thyristor Surge Suppressor) device is located across the tip-to-ring after a limiting resistor and fuse combination. RTIP and RRING resistors are optional depending upon the TSS device selection. Without the resistors, the PP3100SB/SC is recommended. However, with a resistance value of 7.5 Ohms for tip and ring, the PP3100SA is recommended. Digital signals may use a lower TSS device depending upon the total tip to ring voltage range. Selection of the TSS device, either PPxxxxSA or SB/SC is based upon the value of the tip and ring resistors. For the National Electric Code (NEC) article 800, it is recommended that at least one fuse be used in the tip or ring line for metallic surges. Fuses may be replaced with a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device.
TIP
Fuse
RTip
To Protected Equipment
RING RRing
FiguRe 2 - ul 1459 & FCC PART 68 longiTuDinAl PRoTeCTion
There are two TSS devices, one located from tip-to-ground and one ring-to-ground. For standard analog signals, the PP3100SA is recommended with a typical resistor value for tip and ring of 15 Ohms. The PP3100SB/SC is recommended for resistor values of 7.5 Ohms each. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. The purpose of this circuit is to limit AC power current from getting on the ground line causing any safety hazard.
RTip TIP
To Protected Equipment
RING RRing
05081.R11 2/11
Page 5
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
APPliCATion inFoRmATion FiguRe 3 - ul 1459 & FCC PART 68 meTAlliC & longiTuDinAl PRoTeCTion
Three equal TSS devices are used in this application for metallic (tip-to-ring) and longitudinal (tip-to-ground and ring-to-ground) protection. For analog signals, the PP3100SB/SC is recommended. With a resistance value of 15 Ohms for the tip and ring resistors, the PP3100SA may be used. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. This circuit is recommended for protection against the Bellcore requirement: First Level Lightning Surge Tests (Telecommunications Port), document # GR-1089-CORE.
RTip TIP To Protected Equipment
RING RRing
CiRCuiT boARD ReCommenDATionS
Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: • The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. • The path length between the TVS device and the protected line should be minimized. • All conductive loops including power and ground loops should be minimized. • The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. • Ground planes should be used whenever possible. For multilayer PCBs, use ground vias.
05081.R11 2/11
Page 6
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
Do-214AA PACkAge inFoRmATion
ouTline DimenSionS
Dim
A B C D E F G H noTeS
Polarity Band mAX
0.087 0.180 0.155 0.098 0.060 0.008 0.220 0.012
millimeTeRS min
1.96 4.06 3.30 2.00 0.76 0.10 5.08 0.15
inCheS min
0.077 0.160 0.130 0.079 0.030 0.004 0.200 0.006
mAX
2.21 4.57 3.94 2.50 1.52 0.20 5.59 031
A
C
B H D
1. Dimensions are exclusive of mold flash and metal burrs.
E G
F
PAD lAyouT DimenSionS
Dim
A B C D
millimeTeRS min
2.10 1.27 1.27
inCheS min
0.083 0.050 0.083
A
-
mAX
2.69 -
mAX B C D
0.106 -
05081.R11 2/11
Page 7
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
TAPe AnD Reel
P0 t D 10 Pitches Cumulative Tolerance on tape ± 0.2 E
F W K0 B0
A0
P User Direction of Feed
SPeCiFiCATionS
Reel DiA. 330mm (13”)
1. 2. 3. 4.
TAPe WiDTh 12mm
A0
b0
k0
D
e
F
W
P0
P
tmax
3.79 ± 0.15 5.72 ± 0.15 2.46 ± 0.30 1.55 ± 0.05 1.75 ± 0.10
5.5 ± 0.05 12.00 ± 0.30 4.00 ± 0.10 8.00 ± 0.10 0.25 ± 0.10
noTeS
Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T = 13” Reel - 3,000 pieces per 12mm tape. Marking on Part - marking code (see page 2) and logo.
Package outline, pad layout and tape specifications per document number 06013.R5 2/11
oRDeRing inFoRmATion
bASe PART numbeR
PPxxxxSA/SB/SC
leADFRee SuFFiX
-LF
TAPe SuFFiX
-T
QTy/Reel
3,000
Reel Size
13”
Tube QTy
n/a
05081.R11 2/11
Page 8
www.protekdevices.com
05081
Only One Name Means ProTek’Tion™
PP0640SA - PP3500SC
ComPAny inFoRmATion
ComPAny PRoFile ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), inductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide application specific protection solutions for all electronic equipment/systems. ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products. ConTACT uS Corporate headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA by Telephone General: 602-431-8101 Sales: 602-414-5109 Customer Service: 602-414-5114 by Fax General: 602-431-2288 by e-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com Web www.protekdevices.com www.protekanalog.com
COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory.
05081.R11 2/11
Page 9
www.protekdevices.com
很抱歉,暂时无法提供与“PP0720SA”相匹配的价格&库存,您可以联系我们找货
免费人工找货