PP2300SA

05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC ThyRiSToR SuRge SuPPReSSoR DeSCRiPTion The PP-SM Series are thyristor surge suppression (TSS) devices designed to protect telecommunication equipment against lightning and transients induced by AC power lines. These devices can be used on central office equipment, PBX, DSU, OCU and other telecommunication equiment/systems. The bidirectional configuration provides protection for both positive and negative transients and the discrete surface mount package allows for individual placement of the device on line cards or other locations where multiple component devices do not offer the versatile in board trace layout. This series can be used to provide protection in accordance with industry standards such as FCC Part 68, ANSI C62.41, UL 1459, GR-1089-CORE, IEC 61000-2, IEC 61000-4 and IEC 61000-4-5 requirements. Do-214AA PACkAge FeATuReS • Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV • Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns • Compatible with IEC 61000-4-5 (Surge): 95A, 8/20µs - L4(LineGround), 48A - L4(Line-Line) & 83A - L2(Power) • FCC Part 68, UL 1459, Bellcore 1089 & ITU-K.20/K.21 Compliant • UL File Recognition #E208219 • Peak Off-State Voltage from 25 to 300 Volts • Surge Current Capability (See Table 1) • ESD Protection > 25 kilovolts • Low Capacitance for T1/E1 Trunk & Line Card Applications • Bidirectional Configuration • RoHS Compliant • REACH Compliant APPliCATionS • • • • • • T1/E1 Trunk & Line Cards SLIC Line Card DBX Branch Exchange Switches FCC Part 68 Customer Premise Equipment Line Interface Modem xDSL Architecture Interface meChAniCAl ChARACTeRiSTiCS • • • • Molded Plastic DO-214AA Package Approximate Weight: 2.5 grams Lead-Free Pure-Tin Plating (Annealed) Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C • Flammability Rating UL 94V-0 • 12mm Tape and Reel per EIA Standard 481 DEVICE SYMBOL BIDIRECTIONAL TAble 1 - SuRge RATingS SeRieS i PP 2/10µs AmPS 150 300 500 i PP 8/20µs AmPS 150 300 400 i PP 10/160µs AmPS 100 150 200 i PP 10/560µs AmPS 50 100 200 i PP 10/1000µs AmPS 50 80 100 i TSm 60hz AmPS 20 32 60 di/dt A/µs (note 1) 500 500 500 dv/dt V/µs (note 1) 2000 2000 2000 SA SB SC noTeS 1. Critical rate of rise for On-State Current (di/dt) and Off-State Voltage (dv/dt). 05081.R11 2/11 Page 1 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC TyPiCAl DeViCe ChARACTeRiSTiCS mAXimum RATingS @ 25°C unless otherwise Specified PARAmeTeR Surge Current - 50/60Hz (SC Series) Junction Temperature Storage Temperature Thermal Resistance (Junction) - SA & SB Series Thermal Resistance (Junction) - SC Series Thermal Resistance (Ambient) - SA & SB Series Thermal Resistance (Ambient) - SC Series Symbol ITSM TA TSTG RQJC RQJC RQJA RQJA VAlue 60 -40 to 150 -55 to 150 28 26 90 85 uniTS Amps °C °C °C/Watt °C/Watt °C/Watt °C/Watt FiguRe 1 PulSe WAVeFoRm tf iPP - Peak Pulse Current - % of iPP 100 FiguRe 2 Vi ChARACTeRiSiTC CuRVe TEST WAVEFORM PARAMETERS tf = 10µs td = 1000µs IPP ITSM IT IS IH VS IDRM VT VDRM Peak Value IPP td = t/(IPP/2) 50 e-t 0 0 1 t - Time - ms 2 3 100 non-Repetitive on-State Current (iTSm) - Amps FiguRe 3 on-STATe CuRRenT VS SuRge CuRRenT DuRATion PPxxxxSA PPxxxxSC 10 PPxxxxSB 1 1 10 100 Surge Current Duration - Full Cycles Supply Frequency - 60 hz Sinusoidal Page 2 1000 05081.R11 2/11 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC TyPiCAl DeViCe ChARACTeRiSTiCS eleCTRiCAl ChARACTeRiSTiCS PeR line @ 25°C unless otherwise Specified PART numbeR DeViCe mARking RePeTiTiVe SWiTChing minimum SWiTChing mAXimum PeAk VolTAge holDing CuRRenT oFF-STATe CuRRenT CuRRenT oFF-STATe VolTAge (Fig. 7) (Fig. 4) @100V/µs di/dt = 1A/ms @V DRm V DRm VS ih iS i DRm VolTS VolTS mA mA µA 58 65 75 90 120 140 160 190 220 275 300 25 58 65 75 90 120 140 160 190 220 275 300 58 65 75 90 120 140 160 190 220 275 300 77 88 98 130 160 180 220 260 300 350 400 40 77 88 98 130 160 180 220 260 300 350 400 77 88 98 130 160 180 220 260 300 350 400 150 150 150 150 150 150 150 150 150 150 150 50 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 mAXimum on-STATe VolTAge (Fig. 5) @i T VT VolTS 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 on-STATe CuRRenT TyPiCAl CAPACiTAnCe (note 1) @2V, 1mhz C pF 60 60 60 60 40 40 40 30 30 30 30 110 60 60 60 60 40 40 40 30 30 30 30 120 120 120 120 80 80 80 60 60 60 60 iT AmPS 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 PP0640SA PP0720SA PP0800SA PP1100SA PP1300SA PP1500SA PP1800SA PP2300SA PP2600SA PP3100SA PP3500SA PP0300SB PP0640SB PP0720SB PP0800SB PP1100SB PP1300SB PP1500SB PP1800SB PP2300SB PP2600SB PP3100SB PP3500SB PP0640SC PP0720SC PP0800SC PP1100SC PP1300SC PP1500SC PP1800SC PP2300SC PP2600SC PP3100SC PP3500SC GC GD GE GF GG GH GI GJ GK GL GM GN GP GQ GR GS GT GU GV GW GX GY GZ HC HD HE HF HG HH HI HJ HK HL HM 1. Capacitance imblance between positive and negative polarities is typically < 15pF. 05081.R11 2/11 Page 3 www.protekdevices.com noTeS 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC TyPiCAl DeViCe ChARACTeRiSTiCS FiguRe 4 TyPiCAl PeAk oFF-STATe CuRRenT VS junCTion TemPeRATuRe FiguRe 5 TyPiCAl PeAk on-STATe CuRRenT VS on-STATe VolTAge 10 iDRm - Peak off-State Current - µA 100 1 iT - on-State Current - A 0 40 80 tA - Temperature - °C 120 10 0.1 0.01 -40 1 0 1 2 3 4 5 VT - on-State Voltage - V 6 7 FiguRe 6 TyPiCAl noRmAlizeD SWiTChing VolTAge VS junCTion TemPeRATuRe 1.10 normalized VS normalized ih FiguRe 7 TyPiCAl noRmAlizeD holDing CuRRenT VS junCTion TemPeRATuRe 2 1 1 0.9 0.8 -40 0 40 80 tA - Temperature - °C 120 0 -40 0 40 80 tA - Temperature - °C 120 05081.R11 2/11 Page 4 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC APPliCATion inFoRmATion FiguRe 1 - ul 1459 & FCC PART 68 meTAlliC PRoTeCTion The TSS (Thyristor Surge Suppressor) device is located across the tip-to-ring after a limiting resistor and fuse combination. RTIP and RRING resistors are optional depending upon the TSS device selection. Without the resistors, the PP3100SB/SC is recommended. However, with a resistance value of 7.5 Ohms for tip and ring, the PP3100SA is recommended. Digital signals may use a lower TSS device depending upon the total tip to ring voltage range. Selection of the TSS device, either PPxxxxSA or SB/SC is based upon the value of the tip and ring resistors. For the National Electric Code (NEC) article 800, it is recommended that at least one fuse be used in the tip or ring line for metallic surges. Fuses may be replaced with a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device. TIP Fuse RTip To Protected Equipment RING RRing FiguRe 2 - ul 1459 & FCC PART 68 longiTuDinAl PRoTeCTion There are two TSS devices, one located from tip-to-ground and one ring-to-ground. For standard analog signals, the PP3100SA is recommended with a typical resistor value for tip and ring of 15 Ohms. The PP3100SB/SC is recommended for resistor values of 7.5 Ohms each. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. The purpose of this circuit is to limit AC power current from getting on the ground line causing any safety hazard. RTip TIP To Protected Equipment RING RRing 05081.R11 2/11 Page 5 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC APPliCATion inFoRmATion FiguRe 3 - ul 1459 & FCC PART 68 meTAlliC & longiTuDinAl PRoTeCTion Three equal TSS devices are used in this application for metallic (tip-to-ring) and longitudinal (tip-to-ground and ring-to-ground) protection. For analog signals, the PP3100SB/SC is recommended. With a resistance value of 15 Ohms for the tip and ring resistors, the PP3100SA may be used. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. This circuit is recommended for protection against the Bellcore requirement: First Level Lightning Surge Tests (Telecommunications Port), document # GR-1089-CORE. RTip TIP To Protected Equipment RING RRing CiRCuiT boARD ReCommenDATionS Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: • The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. • The path length between the TVS device and the protected line should be minimized. • All conductive loops including power and ground loops should be minimized. • The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. • Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05081.R11 2/11 Page 6 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC Do-214AA PACkAge inFoRmATion ouTline DimenSionS Dim A B C D E F G H noTeS Polarity Band mAX 0.087 0.180 0.155 0.098 0.060 0.008 0.220 0.012 millimeTeRS min 1.96 4.06 3.30 2.00 0.76 0.10 5.08 0.15 inCheS min 0.077 0.160 0.130 0.079 0.030 0.004 0.200 0.006 mAX 2.21 4.57 3.94 2.50 1.52 0.20 5.59 031 A C B H D 1. Dimensions are exclusive of mold flash and metal burrs. E G F PAD lAyouT DimenSionS Dim A B C D millimeTeRS min 2.10 1.27 1.27 inCheS min 0.083 0.050 0.083 A - mAX 2.69 - mAX B C D 0.106 - 05081.R11 2/11 Page 7 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC TAPe AnD Reel P0 t D 10 Pitches Cumulative Tolerance on tape ± 0.2 E F W K0 B0 A0 P User Direction of Feed SPeCiFiCATionS Reel DiA. 330mm (13”) 1. 2. 3. 4. TAPe WiDTh 12mm A0 b0 k0 D e F W P0 P tmax 3.79 ± 0.15 5.72 ± 0.15 2.46 ± 0.30 1.55 ± 0.05 1.75 ± 0.10 5.5 ± 0.05 12.00 ± 0.30 4.00 ± 0.10 8.00 ± 0.10 0.25 ± 0.10 noTeS Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T = 13” Reel - 3,000 pieces per 12mm tape. Marking on Part - marking code (see page 2) and logo. Package outline, pad layout and tape specifications per document number 06013.R5 2/11 oRDeRing inFoRmATion bASe PART numbeR PPxxxxSA/SB/SC leADFRee SuFFiX -LF TAPe SuFFiX -T QTy/Reel 3,000 Reel Size 13” Tube QTy n/a 05081.R11 2/11 Page 8 www.protekdevices.com 05081 Only One Name Means ProTek’Tion™ PP0640SA - PP3500SC ComPAny inFoRmATion ComPAny PRoFile ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), inductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide application specific protection solutions for all electronic equipment/systems. ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products. ConTACT uS Corporate headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA by Telephone General: 602-431-8101 Sales: 602-414-5109 Customer Service: 602-414-5114 by Fax General: 602-431-2288 by e-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com Web www.protekdevices.com www.protekanalog.com COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05081.R11 2/11 Page 9 www.protekdevices.com