USB0412C-LF-T7

05205 USB0403 thru USB0424C LOW CAPACITANCE TVS ARRAY APPLICATIONS ✔ Ethernet - 10/100 Base T ✔ Cellular Phones ✔ Audio & Video Inputs ✔ FireWire, SCSI & USB Interfaces IEC COMPATIBILITY ( EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) SOT-143 FEATURES ✔ 500 Watts Peak Pulse Power per Line (tp=8/20µs) ✔ Unidirectional & Bidirectional Configurations ✔ Available in Multiple Voltage Types Ranging From 3V to 24V ✔ Protects One Line ✔ ESD Protection > 40 kilovolts ✔ Low Leakage ✔ Low Capacitance: 5pF per Line Pair ✔ RoHS Compliant in Lead-Free Versions MECHANICAL CHARACTERISTICS ✔ ✔ ✔ ✔ Molded JEDEC SOT-143 Package Weight 9 milligrams (Approximate) Available in Tin-Lead or Lead-Free Pure-Tin Plating(Annealed) Solder Reflow Temperature: Tin-Lead - Sn/Pb, 85/15: 240-245°C Pure-Tin - Sn, 100: 260-270°C ✔ Flammability Rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 ✔ Marking: Marking Code PIN CONFIGURATIONS UNIDIRECTIONAL BIDIRECTIONAL 1 4 1 4 2 3 2 3 05205.R1 6/06 1 www.protekdevices.com USB0403 thru USB0424C DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified PARAMETER Peak Pulse Power (tp = 8/20µs) - See Figure 1 Operating Temperature Storage Temperature SYMBOL PPP TJ TSTG VALUE 500 -55°C to 150°C -55°C to 150°C UNITS Watts °C °C ELECTRICAL CHARACTERISTICS PER LINE PART NUMBER (See Notes 1-2) DEVICE MARKING RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE @ 25°C Unless Otherwise Specified MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) @ IP = 5A VC VOLTS 9.0 9.0 11.0 11.0 16.6 16.6 24.0 24.0 30.0 30.0 N/A N/A V WM VOLTS USB0403 USB0403C USB0405 USB0405C USB0408 USB0408C USB0412 USB0412C USB0415 USB0415C USB0424 USB0424C 3U 3B 5U 5B 8U 8B 12U 12B 15U 15B 24U 24B 3.3 3.3 5.0 5.0 8.0 8.0 12.0 12.0 15.0 15.0 24.0 24.0 @ 1mA V(BR) VOLTS 4.0 4.0 6.0 6.0 8.5 8.5 13.3 13.3 16.6 16.6 26.7 26.7 @8/20µs VC @ IPP 19.0V @ 20.0A 19.0V @ 20.0A 18.3V @ 17.0A 18.3V @ 17.0A 18.5V @ 17.0A 18.5V @ 17.0A 28.6V @ 11.0A 28.6V @ 11.0A 31.8V @ 10.0A 31.8V @ 10.0A 56.0V @ 6.0A 56.0V @ 6.0A @VWM ID µA 125 125 20 20 10 10 1 1 1 1 1 1 0V @ 1 MHz C pF 5 5 5 5 5 5 5 5 5 5 5 5 Note 1: Part numbers with an additional “C” suffix are bidirectional devices, i.e., USB0405C. Note 2: Unidirectional Only: Positive potential is applied from pin 2 to 1 or pin 3 to 4. 10,000 PPP - Peak Pulse Power - Watts FIGURE 1 PEAK PULSE POWER VS PULSE TIME IPP - Peak Pulse Current - % of IPP 120 100 80 60 40 20 0 tf FIGURE 2 PULSE WAVE FORM Peak Value IPP TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs 1,000 500W 8/20µs Waveform e-t 100 td = t I /2 PP 10 0.1 1 10 100 td - Pulse Duration - µs 1,000 10,000 0 5 10 15 20 t - Time - µs 25 30 05205.R1 6/06 2 www.protekdevices.com USB0403 thru USB0424C GRAPHS 100 80 % Of Rated Power FIGURE 3 POWER DERATING CURVE 40 Peak Pulse Power 8/20µs 5 Volts per Division FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR USB0405C 30 60 20 40 20 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - °C 150 10 0 ESD Test Pulse: 5 kilovolt, 1/30ns (waveform) FIGURE 5 INSERTION LOSS - USB0405C FIGURE 6 RETURN LOSS - USB0405C 20 db 10 db per Division 10 db per Division 20 db Ref 0 db Ref 0 db -20 db -20 db -50 db 100 MHz per Division -50 db 100 MHz per Division 05205.R1 6/06 3 www.protekdevices.com USB0403 thru USB0424C APPLICATIONS The USB04 Series are TVS arrays designed to protect I/O or data lines from the damaging effects of ESD and EFT. This product series provides both unidirectional and bidirectional protection, with a surge capability of 500 Watts PPP per line for an 8/20µs waveform and ESD protection > 40kV. UNIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 1) The two USB04 Series devices provide protection in a commonmode configuration as depicted in Figure 1. Circuit connectivity is as follows: ✔ TVS Device 1: Line 1(D+) is connected to Pins 2 & 3. ✔ TVS Device 2: Line 2(D-) is connected to Pins 2 & 3. ✔ Both TVS Devices: Pins 1 & 4 connected to ground. USB OUTPUT CONNECTOR Figure 1 - Unidirectional Configuration (Two TVS Devices) Common-Mode USB Protection ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; 1 4 1 4 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; GND SOLDER PAD 2 3 2 3 USB IC D+ D- R 2 TX 3 CIRCUIT BOARD LAYOUT RECOMMENDATIONS Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: ✔ The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. The path length between the TVS device and the protected line should be minimized. All conductive loops including power and ground loops should be minimized. The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. ✔ ✔ ✔ ✔ 05205.R1 6/06 4 www.protekdevices.com RJ-45 Circuit connectivity is as follows: ✔ Line 1(RX) is connected to Pins 1 & 4. ✔ Line 2(TX) is connected to Pins 2 & 3. ETHERNET TRANSCEIVER BIDIRECTIONAL DIFFERENTIAL-MODE CONFIGURATION (Figure 2) The USB04xxC Series provides protection in a differential-mode configuration as depicted in Figure 2. Figure 2 - Bidirectional Configuration Differential-Mode Ethernet Protection RX R 1 4 USB0403 thru USB0424C SOT-143 PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE SOT-143 A G L B S J DIM PACKAGE DIMENSIONS MILLIMETERS MIN MAX 2.80 1.20 0.84 0.39 0.79 1.78 0.013 0.08 0.46 0.445 0.72 2.11 3.04 1.39 1.14 0.50 0.93 2.03 0.10 0.15 0.60 0.60 0.83 2.48 INCHES MIN MAX 0.110 0.047 0.033 0.015 0.031 0.070 0.0005 0.003 0.018 0.0175 0.028 0.083 0.120 0.055 0.045 0.020 0.037 0.080 0.004 0.006 0.024 0.024 0.033 0.098 K F D H C R MOUNTING PAD TYPICAL DIM Millimeters Inches 1 2 3 4 5 6 7 8 9 10 1 1 2.85 2.00 1.80 1.90 1.05 2.75 1.20 0.80 0.85 0.85 0.85 0.112 0.079 0.071 0.075 0.041 0.108 0.047 0.031 0.033 0.033 0.033 A B C D F G H J K L R S NOTES 1 2 10 4 5 11 6 1. Dimensioning and tolerances per ANSI Y14.5M, 1985. 2. Controlling Dimension: Inches 3. Dimensions are exclusive of mold flash and metal burrs. TAPE & REEL ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 3,000 pieces per 8mm tape, i.e., USB0405C-T7. 3. Suffix-T13 = 13 Inch Reel - 10,000 pieces per 8mm tape, i.e., USB0405C-T13. 4. Suffix - LF = Lead-Free, Pure-Tin Plating, i.e., USB0405C-LF-T7. 3 7 8 9 Outline & Dimensions: Rev 2 - 6/06, 06011 Tape & Reel Specifications (Dimensions in millimeters) Reel Dia. 178mm (7”) Tape Width 8mm A0 B0 K0 D E F W P0 P2 P tmax 0.25 3.10 ± 0.10 2.70 ± 0.10 1.35 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 3.50 ± 0.05 8.00 ±0.30 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 P0 t D P2 10 Pitches Cumulative Tolerance on Tape. ± 0.2 E Top cover tape A0 K0 B0 F W P User Direction of Feed COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com Web Site: www.protekdevices.com www.protekdevices.com 05205.R1 6/06 5