J0011D11

PULSEJACK TM THROUGH HOLE, TAB DOWN, RJ-45 JACK WITH INTEGRATED MAGNETICS For 10/100Base-TX NIC Applications Magnetic designs to support every PHY Meets or exceeds IEEE 802.3 and ANSI X3.263 standards including 350 µH min OCL with 8 mA bias Patented InterLock Base construction for high reliability High performance for maximum EMI suppression Minimum 1500 Vrms isolation per IEEE 802.3 requirement Independent connector evaluation completed (Contech Research, Massachusetts) Electrical Specifications @ 25°C — Operating Temperature 0°C to +70°C Turns1,2 Ratios LEDs3 Insertion Loss TX/RX (dB MAX) L/R 1-65 MHz Part Number Return Loss (dB MIN) 100 W (± 15 W) 1-10 MHz 10-30 MHz Common Mode Rejection (dB TYP) Crosstalk (dB TYP) 30-60 MHz 60-80 MHz 1-30 MHz 30-60 MHz 60-100 MHz 1-50 MHz 50-150 MHz Hipot (Vrms MIN) @60 Hz 1 MIN TX RX J0006D21 1CT:1 1CT:1 ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0006D21B 1CT:1 1CT:1 G/Y -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0010D11 N/A N/A ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0011D11 1CT:1CT 1CT:1CT ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0011D21 1CT:1CT 1CT:1CT ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0011D21B 1CT:1CT 1CT:1CT G/Y -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D01B 1CT:1CT 1CT:1CT G/Y -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D01F4 1CT:1CT 1CT:1CT G/Y -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D11 1CT:1CT 1CT:1CT ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D21 1CT:1CT 1CT:1CT ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D21E 1CT:1CT 1CT:1CT G/G -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 1CT:1CT 1CT:1CT YG/G -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0026D21G5 J0033D21 J0035D21B 1.25CT:1CT 1CT:1CT 1CT:1CT 1CT:1CT G/Y N/A N/A ¾ -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0048D21M 1CT:1 1CT:1 G/G -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0073D01B 1CT:2.5CT 1CT:1 G/Y -1.0 -20 -16 -12 -10 -40 -35 -30 -30 -20 1500 J0037D21 Notes: 1. Both transmit and receive channels meet IEEE 802.3 specifications. 2. Different electrical and mechanical specifications can be accommodated; contact Pulse Applications Engineering. = none. 3. LEDs Left/Right: G = green; Y = yellow; 4. LEDs with internal resistor. 5. Bi-color Left LED ¾ This is a single port platform. Contact Applications Engineering for other platforms at (858) 674-8100 for more information. US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com · · · · 1 · · PRELIMINARY J403.P (2/02) PULSEJACK THROUGH HOLE, TAB DOWN RJ-45 JACK WITH INTEGRATED MAGNETICS TM For 10/100Base-TX NIC Applications Mechanicals .850 21,59MAX .630 16,00 .290 7,37 .135 .020 3,43 0,51 .535 13,59 LEFT LED Patent Pending .125 .020 3,18 0,51 HOUSING POST JXXXXXXXX Date Code SIGNAL PINS FRONT RIGHT LED TM BACK Country of Origin .130 .020 3,30 0,51 .140 3,56 SHIELD PIN FRONT VIEW BACK VIEW SIDE VIEW .425 10,80 .620 15,75 .498 12,65 .450 11,43 .398 10,11 4X R .010 MAX R 2.54 0,25 6,45 .660 16,76 .100 2,54 4X 2X .193 4,90 9 11 .133 3,38 10 12 .120 3,05 7 8 .100 2,54 5 6 3 4 FACE VIEW .024 0,61 FRONT 2X .064 SHIELD PIN 1,63 .010 TOP OF PCB 0,25 TO BOTTOM OF OPENING .250 6,35 1 RECOMMENDED PANEL CUTOUT 2 BACK .560 14,22 .040 1,02 .128 3,25 HOUSING POST .050 1,27 8X .035 0,89 .003 0,08 .350 8,89 Standard LED Wavelength Forward* V(MAX) (TYP) Yellow Green 585 nm 565 nm 2.5 V 2.5 V 2.1 V 2.2 V * With a forward current of 20 mA SUGGESTED PCB LAYOUT Dimensions: Inches mm Unless otherwise specified, all tolerances are ± .010 0,25 US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com · · · · 2 · · PRELIMINARY J403.P (2/02) PULSEJACK THROUGH HOLE, TAB DOWN RJ-45 JACK WITH INTEGRATED MAGNETICS TM For 10/100Base-TX NIC Applications Schematics J0010 TX+ 1 TD- 2 2 TX- 3 RX+ RX+ 3 CT 5 6 RX- RX- 6 1CT : 1 RECEIVE Right LED 75 TX- 2 RX+ 3 3 RX+ RD- 6 RX- 4 4 5 7 6 4 5 5 7 7 8 8 1 TX+ 1CT : 1CT RECEIVE 6 RX- 3 RX+ CT 6 RD- 8 75 CT 3 RD- 1 1CT :1CT RECEIVE 75 75 5 7 0.001mF 8 CHS GROUND 5 75 75 C1 NOTE: Connect CHS GND to PCB ground. 8 NOTE: Connect CHS GND to PCB ground. J0073 J0048 TX+ 1 6 RX- 75 4 7 CHS GROUND 5 J0037 1 TX+ 1 TX+ TD+ 1 1 TX+ TX+ 1 CT 2 TRANSMIT 4 CT 3 T1 RECEIVE 5 T2 6 6 RX- RX+ 4 CT 5 RD- 6 RD+ 7 CHS GROUND 8 7 8 3 RX+ CT 6 RD- 8 1CT : 1 RECEIVE 75 0.001mF 2Kv 75 6 RX4 4 75 4 5 7 5 8 6 RX- 1CT : 1 RECEIVE NC 7 4 7 3 RX+ 2 TX- 1CT : 2.5CT TRANSMIT CABLE SIDE 3 RX+ PCB SIDE TO PHY RX+ 3 TD- 2 2 TX- 1CT : 1 TRANSMIT CABLE SIDE 2 TX- PCB SIDE TO PHY TX- 3 2 CABLE SIDE PCB SIDE TO PHY 3 RX+ 4 5 75 0.001mF NOTE: Connect CHS GND to PCB ground. RD- RX+ 2 4 75 7 8 2 TX- 1CT :1CT TRANSMIT 75 4 75 0.001mF 6 RX- 1CT : 1CT RECEIVE 4 5 8 1 TX+ TX- 7 2 TX- 1.25CT : 1CT TRANSMIT RD+ 7 75 75 75 CT 6 PCB SIDE TO PHY RD- 8 TD- 0.001mF TX+ 8 CABLE SIDE CT 6 PCB SIDE TO PHY 3 RX+ CABLE SIDE PCB SIDE TO PHY RD+ 7 C1 75 J0035 1 TX+ TD- 2 2 TX- 4 5 7 CT 3 1CT : 1CT TRANSMIT 6 RX- 1CT : 1CT RECEIVE NOTE: Connect CHS GND to PCB ground. TD+ 1 CT 3 CHS GROUND 5 75 RD- 6 J0033 TD+ 1 4 3 RX+ CT 5 CHS GROUND 8 8 J0026 TD- 2 RX+ 3 NC 7 7 8 2 TX- 1CT : 1CT TRANSMIT CABLE SIDE Left LED 1CT : 1 TRANSMIT 1 TX+ CT 4 PCB SIDE TO PHY LEDs with Internal Resistors 12 11 1 TX+ CABLE SIDE Right LED 9 10 TX+ 1 2 TX- PCB SIDE TO PHY PCB SIDE TO PHY TX- 2 CABLE SIDE Left LED 12 11 TX+ 1 1 TX+ CT 4 LEDs without Internal Resistors 9 10 J0011 CABLE SIDE J0006 LED Configuration 75 75 7 0.001mF CHS GROUND 5 8 NOTE: Connect CHS GND to PCB ground. 5 75 8 NOTE: Connect CHS GND to PCB ground. US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com · · · · 3 · · PRELIMINARY J403.P (2/02) PULSEJACK TM THROUGH HOLE, TAB DOWN RJ-45 JACK WITH INTEGRATED MAGNETICS For 10/100Base-TX NIC Applications Application Notes Advantages of the PulseJack Modules Increased Reliability Consistent Electrical and Magnetic Performance Pulse developed a patented method for ensuring the quality, consistency, and connection integrity of encapsulated coils and other three-dimensional electronic components. The InterLock Base consists of an internal plastic carrier that holds the coil firmly in place and provides precisely engineered “lead-channels” to lock together the lead wires and the leadframe pins. All of the InterLock Base interconnections are then simultaneously dip soldered, providing for both efficiency and uniformity for best common mode rejection and crosstalk. - With internal magnetics specifically oriented on all parts, there are more consistent on all functional tests. This is optimized for best crosstalk, common mode rejection and return loss. - With the selection of common mode material and winding techniques, common mode noise rejection maintains integrity to higher frequencies. - Multiple tabs around shield-to-ground, shield-to-chassis, and shunt noise to ground for improved EMI suppression. Higher Manufacturing Yields Because of this Pulse patented higher reliability method, there is less of a chance of opens and shorts, thus providing higher yields. Materials Housing Contacts PCB Pins Shield Thermoplastic - UL94V-0 Phosphorous Bronze, Nickel underplating and selective gold plating 50 m inches max. Phosphorous Bronze with 120 m inches Sn90/Pb10 over 50 m inches Nickel. Cartridge Brass with 10-20 m inches Nickel over 10-20 m inches Nickel. Part Numbering System Part Number Format: J X XXX X X X X Example PulseJack Part Number: J 0 Connector Products Platform "0" through hole, locking tab down 8 pin, single. 006 Internal Magnetics Additional electrical specifications can be accommodated. Contact Pulse Applications Engineering. NOTE: Specify resistor value, voltage drop across LED D Shield Type "D" is standard shield type. Additional mechanical specifications can be accommodated. Contact Pulse Applications Engineering. and desired current, or refer to table, page 2. 2 1 EMI Tabs Number of Ports "0": no tabs B LED Options "1" single port "1": 2 tabs top 2 tabs bottom Left LED1 "2": 2 tabs top 2 tabs each side 2 tabs bottom For More Information : "B" "E" "F"2 "G" Yellow Green Yellow Green Note: 1. Front view 2. "F" LEDs include internal resistors. UNITED STATES (Worldwide) UNITED KINGDOM (Northern Europe) FRANCE SINGAPORE (Southern Europe) (Southern Asia) TAIWAN, R.O.C. (Northern Asia) HONG KONG (China/Hong Kong) 12220 World Trade Drive San Diego, CA 92128 U.S.A. http://www.pulseeng.com TEL: 858 674 8100 FAX: 858 674 8262 1 & 2 Huxley Road The Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom TEL: 44 1483 401700 FAX: 44 1483 401701 Zone Industrielle F-39270 Orgelet France TEL: 33 3 84 35 04 04 FAX: 33 3 84 25 46 41 3F-4, No. 81, Sec. 1 HsinTai Wu Road Hsi-Chih, Taipei Hsien Taiwan, R.O.C. Tel: 886 2 2698 0228 FAX: 886 2 2698 0948 19/F, China United Plaza 1008 Tai Nan West Street Cheung Sha Wan, Kowloon Hong Kong, China TEL: 852 2788 6588 FAX: 852 2776 1055 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 TEL: 65 287 8998 FAX: 65 280 0080 Right LED1 Green Green Green Yellow/Green DISTRIBUTOR Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names metioned herein may be trademarks or registered trademarks of their respective owners. Printed on recycled paper. ©2002, Pulse Engineering, Inc. 4 PRELIMINARY J403.P (2/02)