PA2247.223NLT

SMT Power Inductors High Current Composite Inductor - PA2247XXXNLT and PM2247.XXXNLT Height: 10.0mm Max Footprint: 16.8mm x 15.8mm Max Current Rating: up to 30Arms Inductance Range: 4.7uH to 33.0uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA2247) and Automotive (PM2247) grades Electrical Specifications @ 25°C, Operating Temperature Range -55°C to +155°C Part Number Commerical Automotive6 PA2247.472NLT PA2247.562NLT PA2247.682NLT PA2247.822NLT PA2247.103NLT PA2247.153NLT PA2247.223NLT PA2247.333NLT PM2247.472NLT PM2247.562NLT PM2247.682NLT PM2247.822NLT PM2247.103NLT PM2247.153NLT PM2247.223NLT PM2247.333NLT Inductance 100KHz, 0.1V Rated3 Current uH±20% 4.7 5.6 6.8 8.2 10.0 15.0 22.0 33.0 A 30 28 26 25 24 18 16 13 DC Resistance Saturation Current2 (25°C) TYP. MAX. TYP. K Factor for Core Loss mΩ 3.4 3.82 4.18 6.0 7.1 9.2 13.2 18.7 mΩ 3.8 4.2 4.6 7.2 8.6 11.5 15.8 20.0 A 39 34 31 28 26 20 18 16.7 10.9 9.6 9.6 8.6 7.2 6.1 5.0 3.9 Notes: 1. 2. 3. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. The saturation current is the current at which the initial inductance is guaranteed to drop by no more than 40%. The typical inductance at a specified current can be found on the typical performance curves. The rated current is the DC current required to raise the component temperature by approximately 40�C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 1 Power.PulseElectronics.com 4. 5. 6. The part temperature (ambient+temp rise) should not exceed the upper operating temperature range under worst case operating conditions. Circuit design, PCB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. The PMxxxx.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The inductance and mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Special Characteristics P864. D (09/20)   /HDG3E)UHH DQG 5R+6 FRPSOLDQW +DORJHQIUHH  2SHUDWLQJ WHPSHUDWXUH ać,QFOXGLQJ VHOI  WHPSHUDWXUH ULVH  $SSOLFDWLRQV 5HFRPPHQG 3& %RDUG 3DWWHUQ SMT Power Inductors 1RWH 3& SRZHU V\VWHP炻LQFO ,093 High Current Composite Inductor - PA2247XXXNLT and PM2247.XXXNLT + ( PA2247.XXXNLT and PM2247.XXXNLT $ PP A B % PP “ 703)$ $%' “ “ PA2247/PM2247 16.5±0.3 15.5±0.3 *PP +PP  UHI  UHI  UHI 1RWH ǃ7KH DERYH 3&% OD\RXW UHIHUHQFH RQO\ ǃ5HFRPPHQG VROGHU SDVWH WKLFNQHVV DW PP DQG DERYH C “ /PP L ) FINAL LAYOUT 703)$ ' H ( 1/ 6HULHV Series ' & G $ % * Mechanical /  'LPHQVLRQV ( '&'& FRQYHUWHU  & PP ( PP ) PP f f f f f D “ 9.7±0.3 E 13.2±0.5 f “ SUGGESTED PAD LAYOUT ' PP F 3.2±0.2 L 10.4±0.3 ,QGXFWDQFH G H X+ DQG EHORZ 15.0(REF) 6.0 (REF) X+ DQG DERYH 15.0(REF All Dimensions in mm.  3DUW 1XPEHULQJ 703)  $ $ % & $ 6HULHV TAPE & REEL INFO % 'LPHQVLRQ  01 ' (  3$ )  $%' * %[&  6SHFLILFDWLRQ 0DWHULDO Chip cavity Blank portions  X+ 0 “ 3XOVH 3$;;;1/7 0DUNLQJ %ODFN1/ DQG