PA4344.561ANLT

SMT Power Inductor High Current Molded Power Inductor - PA4344.XXXANLT Series Height: 7.0mm Max Footprint: 18.3mm x 17.2mm Max Current Rating: up to 55.0A Inductance Range: 0.47uH to 82uH Shielded construction and compact design High current, low DCR, and high efficiency Minimized acoustic noise and minimized leakage flux Electrical Specifications @ 25°C - Operating Temperature -55°C to +155°C Inductance 100KHz, 1V Rated Current uH±20% PA4344.471ANLT 5,8 Part Number DC Resistance 3 Saturation2 Current SRF K Factor TYP. MAX. TYP. TYP. A mΩ mΩ A MHz 0.47 55 0.7 0.9 100 56 44.2 PA4344.561ANLT 0.56 50 0.81 0.97 70 47 56.1 PA4344.102ANLT 1 42 1.03 1.2 45 32 48.5 PA4344.152ANLT 1.5 35 1.5 1.8 40 26 31.2 PA4344.182ANLT 1.8 32 1.7 2 34 23 30.9 PA4344.222ANLT 2.2 30 1.8 2.2 32 20 25.5 PA4344.332ANLT 3.3 28 2.7 3.3 29 16 18.1 PA4344.472ANLT 4.7 26 3.7 4.5 26 14 13.4 PA4344.682ANLT 6.8 22 6 7.2 22 11 10.2 PA4344.103ANLT 10 19 9.2 10.6 19 9 7.6 PA4344.153ANLT 15 14 12.8 15.5 14 7 7.4 PA4344.223ANLT 22 11.5 20.5 24 11.5 6 5.6 PA4344.333ANLT 33 10 32 37 10 5 4.4 PA4344.473ANLT 47 8.0 40 47 8.0 4 4.3 PA4344.683ANLT 68 6.5 66 76 7.2 4 PA4344.823ANLT 82 5.7 69 83 6.5 3 1 PulseElectronics.com 2.6 P796.G (04/21) SMT Power Inductor High Current Molded Power Inductor - PA4344.XXXANLT Series Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. The saturation current is the current at which the initial inductance drops by approximately 30% at the stated ambient temperature. The maximum allowable drop at this stated current is 40% of the initial inductance. This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effect) to the component. 3. The rated current is the DC current required to raise the component temperature by approximately 40°C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 4. The part temperature (ambient+temp rise) should not exceed maximum operating temperature under worst case operating conditions. Circuit design, PCB trace size and 5. 6. 7. 8. thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. Please note that the inductance tolerance of all parts are ±20%, except those indicated by an * which are +/- 30%. Parts shown in bold are standard catalog parts and are available through sample stock and distribution. Parts in lighter font are available but are not necessarily held in sample stock or distribution and lead times may be longer. Please contact Pulse for availablity. The PM prefix parts are AEC-Q200 qualified and has full automotive IATF16949 certification. The mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) 1.33 and therefore may not strictly conform to PPAP. Special Characteristics Mechanical PA4344.XXXANLT Final Layout SUGGESTED PAD LAYOUT Series A B C D E F G H PA4344.XXXANLT 17.8±0.5 16.9±0.3 6.7±0.3 (11.9) (13.1) (12.5) (3.15) (12.2) All Dimensions in mm. 2 PulseElectronics.com P796.G (04/21) SMT Power Inductor High Current Molded Power Inductor - PA4344.XXXANLT Series TAPE & REEL INFO Marking Marking K0 A W P1 G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) PA4344.XXXANLT TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL Ø330 32.4 24 32 7.5 200 Typical Performance Curves PA4344.471ANLT PA4344.561ANLT PA4344.102ANLT PA4344.152ANLT PA4344.182ANLT PA4344.222ANLT PA4344.332ANLT PA4344.472ANLT PA4344.682ANLT 3 PulseElectronics.com P796.G (04/21) SMT Power Inductor High Current Molded Power Inductor - PA4344.XXXANLT Series PA4344.103ANLT PA4344.153ANLT PA4344.223ANLT PA4344.333ANLT PA4344.473ANLT PA4344.683ANLT PA4344.823ANLT 4 PulseElectronics.com P796.G (04/21) SMT Power Inductor High Current Molded Power Inductor - PA4344.XXXANLT Series Core Loss Bp-p = K *L(uH) *delta I(A) For More Information: Americas - prodinfo_power@pulseelectronics.com | Europe - power-apps-europe@pulseelectronics.com | Asia - power-apps-asia@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2020. Pulse Electronics, Inc. All rights reserved. 5 PulseElectronics.com P796.G (04/21)