PA5006.102NLT

SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT POWER PRODUCTS IA T F 16 Height: 2.05mm Max Footprint: 8.05mm x 7.8mm Max Current Rating: up to 35Apk Inductance Range: 0.27uH to 1.0uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5006) and Automotive (PM2206) grades 949 Electrical Specifications @ 25°C, Operating Temperature Range -55°C to +155°C Saturation2 Part Number DC Resistance Rated3 Inductance Current Current 100KHz, 0.1V TYP. MAX. (25°C) Commerical Automotive6 uH±20% A mΩ mΩ A Mechanical D mm±0.3 K Factor for Core Loss PA5006.271NLT PM2206.271NLT 0.27 21 2.9 3.5 32 6.6 141.7 PA5006.311NLT PM2206.311NLT 0.31 20 4.0 4.8 31 6.2 141.7 PA5006.331NLT PM2206.331NLT 0.33 19 4.0 4.8 31 6.2 141.7 PA5006.471NLT PA5006.681NLT PA5006.102NLT PM2206.471NLT PM2206.681NLT PM2206.102NLT 0.47 0.68 1.00 17 13 11 5.1 7.9 9.8 6.2 9.2 10.8 25 23 20 6.2 6.2 6.2 103.9 82.1 67.8 Notes: 1. 2. 3. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. The saturation current is the current at which the initial inductance is guaranteed to drop by no more than 40%. The typical inductance at a specified current can be found on the typical performance curves. The rated current is the DC current required to raise the component temperature by approximately 40�C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 1 Power.PulseElectronics.com 4. 5. 6. The part temperature (ambient+temp rise) should not exceed 155�C under worst case operating conditions. Circuit design, PCB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. The PM2206.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Special Characteristics P810.D (04/20) SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT POWER PRODUCTS Mechanical PA5006.XXXNLT and PM2206.XXXNLT A H L F G E 　XXX 1R2 1602 D/C B D C FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H PA5006/PM2206 7.8±0.25 7.6±0.2 1.85±0.2 See Spec Table 1.75±0.2 3.15±0.25 7.4 (REF) 2.8(REF) 7.2 (REF) All Dimensions in mm. TAPE & REEL INFO Chip cavity Blank portions A W Blank portions K0 P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) PA5006/PM2206 TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL Ø330 16.4 12 16 2.3 2000 Typical Performance Curves 311NLT 100 0.28 80 0.32 80 0.21 60 0.24 60 0.14 40 0.16 40 0.07 20 0.08 20 0 0.00 0.00 0 7 14 21 28 35 IDC(A) 2 Power.PulseElectronics.com 0 8 16 24 32 40 △T(°C) 0.40 Inductance （uH ） 100 △T(°C) Inductance （uH ） 271NLT 0.35 0 IDC(A) P810.D (04/20) SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT POWER PRODUCTS 471NLT 100 0.36 80 0.48 80 0.27 60 0.36 60 0.18 40 0.24 40 0.09 20 0.12 20 0 0.00 0.00 0 7 14 21 28 35 0 7 14 IDC(A) IDC(A) 80 0.54 60 0.36 40 0.18 20 0.00 0 5 10 15 20 25 IDC(A) 3 Power.PulseElectronics.com 0 0 1.5 100 1.2 80 0.9 60 0.6 40 0.3 20 0.0 △T(°C) 0.72 28 102NLT Inductance （uH ） 100 △T(°C) Inductance （uH ） 681NLT 0.90 21 △T(°C) 0.60 Inductance （uH ） 100 △T(°C) Inductance （uH ） 331NLT 0.45 0 5 10 15 20 25 0 IDC(A) P810.D (04/20) SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT CORE LOSS vs FLUX DENSITY 2.0 200KHz Core Loss (W) 1.8 400KHz 1.6 600KHz 1.4 1000KHz 800KHz 1400KHz 1.2 1800KHz 1.0 0.8 0.6 0.4 0.2 0.0 0 500 1,000 1,500 2,000 2,500 Bp-p (Gauss) Bp-p = K *L(uH) *delta I(A) For More Information: Americas - prodinfo_power@pulseelectronics.com | Europe - power-apps-europe@pulseelectronics.com | Asia - power-apps-asia@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2020. Pulse Electronics, Inc. All rights reserved. 4 Power.PulseElectronics.com P810.D (04/20) POWER PRODUCTS