PA5433.222NLT

SMT Power Inductors High Current Composite Inductor - PA5433.XXXNLT and PM5433.XXXNLT Height: 8.0mm Max Footprint: 16.8mm x 15.8mm Max Current Rating: up to 40Arms Inductance Range: 2.0uH to 22uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5433) and Automotive (PM5433) grades Electrical Specifications @ 25°C, Operating Temperature Range -55°C to +155°C Part Number Commerical Automotive6 PA5433.202NLT PA5433.222NLT PA5433.302NLT PA5433.422NLT PA5433.532NLT PA5433.622NLT PA5433.722NLT PA5433.822NLT PA5433.103NLT PA5433.153NLT PA5433.223NLT PM5433.202NLT PM5433.222NLT PM5433.302NLT PM5433.422NLT PM5433.532NLT PM5433.622NLT PM5433.722NLT PM5433.822NLT PM5433.103NLT PM5433.153NLT PM5433.223NLT Rated3 Current TYP. MAX. uH±20% 2.00 2.20 3.00 4.20 5.30 6.20 7.20 8.20 10.0 15.0 22.0 A 40.0 37.0 34.5 27.0 26.0 23.0 21.0 19.0 16.0 13.0 12.0 mΩ 1.92 2.15 2.50 3.90 4.45 5.40 6.00 6.60 8.00 12.50 19.30 mΩ 2.21 2.48 3.00 4.68 5.34 6.50 7.20 7.92 9.60 15.00 23.20 Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. The saturation current is the current at which the initial inductance is guaranteed to drop by no more than 40%. The typical inductance at a specified current can be found on the typical performance curves. 3. The rated current is the DC current required to raise the component temperature by approximately 40�C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 1 DC Resistance Inductance 100KHz, 0.1V PulseElectronics.com 4. 5. 6. Saturation2 Current (25°C) A 52.0 49.0 41.0 33.0 31.0 31.0 29.0 25.0 21.0 18.0 16.0 K Factor for Core Loss 17.7 17.7 14.6 12.5 10.9 9.6 8.6 8.6 7.8 6.1 4.7 The part temperature (ambient+temp rise) should not exceed the upper operating temperature range under worst case operating conditions. Circuit design, PCB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. The PMxxxx.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The inductance and mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Special Characteristics . P896. A (01/21)  9HU\ ORZ DFRXVWLF QRLVH DQG YHU\ ORZ OHDNDJH IOX[ QRLVH +DORJHQ  +LJK UHOLDELOLW\   /HDG3E)UHH DQG 5R+6 FRPSOLDQW +DORJHQIUHH  2SHUDWLQJ WHPSHUDWXUH ać,QFOXGLQJ VHOI  WHPSHUDWXUH ULVH SMT Power Inductors 5HFRPPHQG 3& %RDUG 3DWWHUQ  $SSOLFDWLRQV High Current Composite Inductor - PA5433.XXXNLT and PM5433.XXXNLT + 1RWH 3& SRZHU V\VWHP炻LQFO ,093 ( Mechanical ( 703)$ ' PA5433/PM5433 A $ PP “ 16.5±0.3 703)$ $%' All Dimensions in mm. “ /PP *PP +PP  UHI  UHI  UHI L ) FINAL LAYOUT 6HULHV H ( 1/ % Series ' & G $ /  'LPHQVLRQV PA5433.XXXNLT and PM5433.XXXNLT * '&'& FRQYHUWHU  1RWH ǃ7KH DERYH 3&% OD\RXW UHIHUHQFH RQO\ ǃ5HFRPPHQG VROGHU SDVWH WKLFNQHVV DW PP DQG DERYH % B PP “ 15.5±0.3 “ & PP C ' PP D ( PPE ) PP SUGGESTED PAD LAYOUT ,QGXFWDQFH F L G H 15.0 (REF) 6.0(REF) 15.0(REF) “ f f f X+ DQG EHORZ “ f f f X+ DQG DERYH 7.7±0.3 13.2±0.5 3.2±0.2 10.4±0.3  3DUW 1XPEHULQJ 703)  $ $ % & $ 6HULHV % 'LPHQVLRQ   01 ' (  3$ )  $%' * %[& & 7\SH ' ,QGXFWDQFHBlank portions ( ,QGXFWDQFH 7ROHUDQFH ) &RGH * 'DWH &RGH W  6SHFLILFDWLRQ 0DWHULDO Blank portions  X+ Chip cavity 0 “ 3XOVH 3$;;;1/7 0DUNLQJ %ODFN1/ DQG