PE-0805CD152GTT

RF Chip Inductors Wire Wound - 0805 Series For More Information Please Visit: Networking.PulseElectronics.com WIRE WOUND RF CHIP INDUCTORS 0805CD SERIES Wire wound ceramic core construction High Q values High self resonant frequency Temperature Range -40 oC to +125 oC Industry 0805 (2012) size and surface mount land pattern 100% Tin Solder Termination Electrical Specifications @ 25°C - Operating Temperature Range -40 oC to +125oC Part Number Tolerance +/-2% Part Number Tolerance +/-5% Inductance 1 (nH) Q2 (MIN) SRF 3 (MHz MIN) RDC 4 (Ω MAX) IDC 5 (mA MAX) PE-0805CD030GTT PE-0805CD030JTT 3.32 @ 250MHz 40 @ 1500MHz 6000 0.08 600 PE-0805CD050GTT PE-0805CD050JTT 5.6 @ 250MHz 50 @ 1500MHz 5500 0.10 600 PE-0805CD080GTT PE-0805CD080JTT 7.9 @ 250MHz 50 @ 1000MHz 4700 0.12 600 PE-0805CD100GTT PE-0805CD100JTT 10.2 @ 250MHz 50 @ 500MHz 4100 0.14 600 PE-0805CD120GTT PE-0805CD120JTT 11.9 @ 250MHz 50 @ 500MHz 4000 0.15 600 PE-0805CD150GTT PE-0805CD150JTT 14.9 @ 250MHz 50 @ 500MHz 3400 0.17 600 PE-0805CD180GTT PE-0805CD180JTT 17.95 @ 250MHz 50 @ 500MHz 3300 0.20 600 PE-0805CD220GTT PE-0805CD220JTT 21.7 @ 250MHz 55 @ 500MHz 2600 0.22 500 PE-0805CD270GTT PE-0805CD270JTT 26.5 @ 250MHz 55 @ 500MHz 2500 0.25 500 PE-0805CD330GTT PE-0805CD330JTT 32.75 @ 250MHz 60 @ 500MHz 2050 0.27 500 PE-0805CD390GTT PE-0805CD390JTT 38.5 @ 250MHz 60 @ 500MHz 2000 0.29 500 PE-0805CD470GTT PE-0805CD470JTT 46.6 @ 200MHz 60 @ 500MHz 1650 0.31 500 PE-0805CD560GTT PE-0805CD560JTT 55.5 @ 200MHz 60 @ 500MHz 1550 0.34 500 PE-0805CD680GTT PE-0805CD680JTT 67.8 @ 200MHz 60 @ 500MHz 1450 0.38 500 PE-0805CD820GTT PE-0805CD820JTT 82.7 @ 150MHz 60 @ 500MHz 1300 0.42 400 PE-0805CD101GTT PE-0805CD101JTT 98.7 @ 150MHz 60 @ 500MHz 1200 400 PE-0805CD111GTT PE-0805CD111JTT 110 @ 150MHz 50 @ 250MHz 1000 0.46 0.48 PE-0805CD121GTT PE-0805CD121JTT 119.7 @ 150MHz 50 @ 250MHz 1100 0.51 400 PE-0805CD151GTT PE-0805CD151JTT 149.4 @ 100MHz 50 @ 250MHz 920 0.56 400 PE-0805CD181GTT PE-0805CD181JTT 179.6 @ 100MHz 50 @ 250MHz 870 0.64 400 PE-0805CD221GTT PE-0805CD221JTT 217 @ 100MHz 45 @ 250MHz 850 0.70 400 PE-0805CD271GTT PE-0805CD331GTT PE-0805CD391GTT PE-0805CD271JTT 269 @ 100MHz 45 @ 250MHz 650 1.00 350 PE-0805CD331JTT PE-0805CD391JTT 331 @ 100MHz 386 @ 50MHz 45 @ 250MHz 35 @ 250MHz 600 560 1.40 310 1.50 290 400 Pulse Jack (Continued on next page) www.networking.pulseelectronics.com WC710.C (7/19) Electronics WIRE WOUND RF CHIP INDUCTORS 0805CD SERIES Electrical Specifications @ 25°C - Operating Temperature Range -40oC to +125oC (continued) Part Number Tolerance +/-2% Part Number Tolerance +/-5% Inductance 1 (nH) Q2 (MIN) SRF 3 (MHz MIN) RDC 4 (Ω MAX) IDC 5 (mA MAX) PE-0805CD471GTT PE-0805CD471JTT 477 @ 25MHz 33 @ 100MHz 375 1.76 250 PE-0805CD561GTT PE-0805CD561JTT 545 @ 25MHz 23 @ 50MHz 340 1.90 230 PE-0805CD681GTT PE-0805CD681JTT 674 @ 25MHz 23 @ 50MHz 188 2.20 190 PE-0805CD821GTT PE-0805CD821JTT 783 @ 25MHz 23 @ 50MHz 215 2.35 180 PE-0805CD102GTT PE-0805CD102JTT 1000 @25MHz 20 @ 50MHz 200 3.60 150 PE-0805CD122GTT PE-0805CD122JTT 1200 @ 25MHz 20 @ 50MHz 200 4.10 120 N/A PE-0805CD152JTT 1500 @ 25MHz 20 @ 50MHz 200 5.00 100 Notes: 1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that inductance information is not stamped on part, because of the extremely small size). 2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture. 3. SRF measured using a HP8753C Network Analyzer. 4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter. 5. Based on a 15�C maximum temperature rise. 6. Check ordered tolerance band carefully: To order a +/-2% tolerance band the ordering code ends with "GTT" while any+/-5% tolerance band ends with "JTT" . Typical Q vs Frequency Typical Inductance vs Frequency Mechanical Pulse Jack 3 Electronics Weight ..................0.012grams www.networking.pulseelectronics.com Dimensions: Inches mm WC710.C (7/19) Unless otherwise specified, all tolerances are ± .010 0,25 WIRE WOUND RF CHIP INDUCTORS 0805FT SERIES Wire wound ferrite core construction High Q values High self resonant frequency Temperature Range -40 oC to +125 oC Industry standard 0805 (2012) size and surface mount land pattern 100% Tin Solder Termination Electrical Specifications @ 25°C - Operating Temperature Range -40oC to +125oC Part Number Tolerance +/-5% Notes: Inductance (uH) 1 2 3 4 5 Q (MIN) SRF (MHz MIN) RDC (Ω MAX) IDC (mA MAX) PE-0805FT102JTT 1.0 @ 7.96MHz 15 @ 7.96MHz 63 1.20 245 PE-0805FT152JTT 1.5 @ 7.96MHz 15 @ 7.96MHz 60 1.45 225 PE-0805FT222JTT 2.2 @ 7.96MHz 15 @ 7.96MHz 58 1.80 200 PE-0805FT332JTT 3.3 @ 7.96MHz 15 @ 7.96MHz 50 2.30 175 PE-0805FT472JTT 4.7 @ 7.96MHz 15 @ 7.96MHz 43 2.80 140 PE-0805FT682JTT 6.8 @ 7.96MHz 15 @ 7.96MHz 36 3.40 115 PE-0805FT103JTT 10 @ 2.52MHz 10 @ 2.52MHz 30 4.70 98 PE-0805FT153JTT 15 @ 2.52MHz 10 @ 2.52MHz 23 6.50 80 PE-0805FT223JTT 22 @ 2.52MHz 10 @ 2.52MHz 20 8.00 68 PE-0805FT333JTT 33 @ 2.52MHz 10 @ 2.52MHz 17 10.70 60 PE-0805FT473JTT 47 @ 2.52MHz 10 @ 2.52MHz 14 13.80 55 PE-0805FT683JTT 68 @ 2.52MHz 8 @ 2.52MHz 11 17.50 49 1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that inductance information is not stamped on part, because of the extremely small size). 2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture. 3. SRF measured using a HP8753C Network Analyzer. 4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter. 5. Based on a 15�C maximum temperature rise. Mechanical Dimensions: Pulse Jack 4 Electronics www.networking.pulseelectronics.com Unless otherwise specified, all tolerances are ± .010 0,25 Weight ..................0.012grams Inches mm WC710.C (7/19) WIRE WOUND RF CHIP INDUCTORS 0805FT SERIES Typical Q vs Frequency Typical Inductance vs Frequency Tape and Reel Specifications Series 0805CD 0805FT Packing Moisture Level = MSL 1 - Storage Temperature - 40oC to +125oC Tape Dimensions (mm) Reels Dimensions (mm) Parts per Reel A B C D E W P1 P2 P3 H T 2000 178 50 13 14.4 8.4 8 2 4 4 2.1 0.3 Notes: P1, P2 and P3 are same for all chip inductor series. Keeping the same dimensions for guide hole and pocket pitch (P1), pocket pitch (P2), guide hold pitch (P3) and tape width (8mm) for all series, enables the packaging machine to maintain the same settings while changing models. The only difference between the series are the parts per reel which contributes to a different length of tapes/reel per model. Pulse Jack 5 www.networking.pulseelectronics.com WC710.C (7/19) Electronics WIRE WOUND RF CHIP INDUCTORS Performance testing Electrical Testing Storage and Operating Temperature Range: -40oC to +125oC Thermal: -40oC to +85oC Moisture Resistance 240 Hours at 70oC Operating Life Inductors are subjected to the extremes for 48 hours. Then tested at 25 oC There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Q values shall not change by more than ±10% Inductors are subjected to 30 cycles for 30 minutes at each extreme. Then tested at 25 oC Inductors are subjected to 10 cycles of 24 hours at 90 to 95% relative humidity Then tested at 24 oC Inductors are subjected to 1000 hours at 85 oC with 85% Relative Humidity with the rated current applied There shall be no Damaged, Open or Shorted Windings Mechanical Testing Temperature Range: Inductors are subjected to the following: Use a solder pot at 260 oC, with RMA Flux. Each termination is immersed in 63Sn/37Pb molten solder for 4 to 6 seconds. There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Q values shall not change by more than ±10% Recommended Solder Heat Resistance Profile Physical Specifications Vibration (Random) Samplers are subjected to random vibrations as per NAVMAT P9492 Mechanical Shock Inductors are subjected to one half sine wave pulse (8700 g's for 0.3ms) in each directional axis for a total of 18 shocks Moisture Resistance Reflow Inductors on to test pads using 63Sn/37 Pb solder paste (IR Reflow profile = 200 oC for 30 seconds or peak 235 oC for 20 seconds) 6 www.networking.pulseelectronics.com There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Q values shall not change by more than ±10% The inductors shall withstand a minimum force of 1000 g's in any direction using a dynamometer force guage Pulse Jack WC710.C (7/19) Electronics