PE-1210CCMC271STS

SMD CHIP CHOKES Wire-Wound Series Wire wound Ferrite 1210 (3225) core Common Mode Noise suppression without attenuating the signal Magnetically shielded for low Rdc and High Current Perfect for USB2.0/3.0, IEEE1349 Fire wire and other LVDS lines Ideal for DC voltage supply lines for Power over Ethernet -PoE/PoE+ PART NUMBER LEGEND PE —1210CCMC XXXS T S PACKAGE STYLE 1210 TERMINATION IMPEDANCE Representative of the impedance value S = Tin plating CORE MATERIAL/RANGE CCMC - FERRITE CHIP CHOKE STYLE PACKAGING S = Standard Range T = Tape & Reel Reel Size Parts per Reel = 3000 1 Networking.PulseElectronics.com W719.A (7/18) WIRE-WOUND CHIP CHOKES SPECIFICATION Electrical Specifications @ 25°C Part Number (25%) Common Mode Impedance @ 100MHz (Ω) DC Resistance (Ω MAX) Rated Voltage (Vdc) Rated Current (mA MAX) Withstanding Voltage (Vdc) Insulation Resistance (MΩ MIN) PE-1210CCMC161STS 160 0.15 50 680 125 10 PE-1210CCMC271STS 270 0.25 50 640 125 10 PE-1210CCMC601STS 600 0.12 50 1000 125 10 PE-1210CCMC102STS 1000 0.35 50 480 125 10 Mechanical 1.8 2.5 3.2 4.00 (0.8) 0.9 2.70 (0.8) 0.9 2.20 0.9 Impedance vs Frequency 10000 COMMON MODE PRODUCT KEY Impedance (Ω) 1000 PE-1210CCMC161STS PE-1210CCMC271STS PE-1210CCMC601STS PE-1210CCMC102STS 100 10 1 DIFFERENTIAL MODE 0.1 1 10 100 1000 10000 Frequency (MHz) 2 Networking.PulseElectronics.com W719.A (7/18) WIRE-WOUND CHIP CHOKES PERFORMANCE TESTING Electrical Testing Storage and Operating Temperature Range: Inductors are subjected to the extremes for 48 hours. -40° to +85°C Then tested at 25°C Thermal: Inductors are subjected to 30 cycles for 30 minutes at each extreme. -40° to +85°C Moisture Resistance There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Then tested at 25°C Q values shall not change by more than ±10% Inductors are subjected to 10 cycles of 24 hours at 70°C with 90 to 95% Relative Humidity Then tested at 25°C Operating Life Inductors are subjected to 1000 hours at 85°C with 85% Relative Humidity with the rated current applied There shall be no Damaged, Open or Shorted Windings Mechanical Testing There shall be no deformation or change in appearance Inductors are subjected to the following: Temperature Range: Use a solder pot at 260C, with RMA Flux. Each termination is immersed in 63Sn/37Pb molten solder for 4 to 6 seconds. Inductance shall not change by more than ±5% Q values shall not change by more than ±10% Recommended Solder Heat Resistance Profile 3 Networking.PulseElectronics.com W719.A (7/18) WIRE-WOUND CHIP CHOKES TAPE AND REEL SPECIFICATIONS 12.8 330 100 2.3 + 0.2/-0 13.0 2.2 Tape Dimensions (mm) Series Parts per Reel W P1 P2 P3 H T 1210CCMC 3000 12 2 8 4 2.3 0.3 For More Information: Americas - prodinfonetworkamericas@pulseelectronics.com | Europe - comms-Apps-Europe@pulseelectronics.com | Asia - prodinfonetworkapac@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2019. Pulse Electronics, Inc. All rights reserved. 4 Networking.PulseElectronics.com W719.A (7/18)