PG1096.152NLT

SMT Power Inductors Round wire Coils– PG1096NL series Inductance Range: 1.5uH to 82uH Current Rating: up to 65Apk Footprint: 26mm x 26mm Max Height: 14.8mm Max No Thermal Aging RoHS Compliant Electrical Specifications @ 25°C - Operating Temperature -40°C to 130°C1 Inductance @ Irated2 µH TYPICAL Part Number Controlled Electrical Specs. Irated 3 (A) Saturation 5 Current Isat (A TYP) DCR 4 (mΩ) MAX Inductance @ 0Adc (µH ± 20%) 25°C 100°C Heating Current 6 Idc (A TYP) Core Loss Factor 7 (K2) PG1096.152NL 1.35 50 0.85 1.5 65 50.5 50 27.9 PG1096.252NL 2.25 45 1.2 2.5 55 43 45 31 PG1096.472NL 4.2 35 1.8 4.7 40 31 35 43.7 PG1096.682NL 6 30 2 6.8 35 27.5 30 50.6 PG1096.103NL 9 24.5 3.15 10 28 21.8 24.5 62 PG1096.183NL 16 18.5 5 18 21 16.5 18.5 83.6 PG1096.223NL 19.5 17 5.5 22 19 14.8 17 90.9 PG1096.333NL 29.5 13.5 10.5 33 15.5 12 13.5 111.5 PG1096.473NL 42.3 11 12.5 47 13 10 11 134.4 PG1096.683NL 61 9.5 15 68 11 8.6 9.5 168.5 PG1096.823NL 73.5 8.5 22 82 10 7.8 8.5 179.3 Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. Inductance at Irated is a typical inductance value for the component taken at rated current. 3. The rated current as listed is either the saturation current (@ 25°C) or the heating current depending on which value is lower. 4. The DCR of the part is measured at an ambient temperature of 20°C±3°C from point a to b as shown below on the mechanical drawing. 5. The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an ambient temperature. This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effect) to the component. 6. The heating current, Idc, is the DC current required to raise the component temperature by approximately 40°C. The heating current is determined by mounting the component on a typical PCB and applying current for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. Take note that the components’ performance varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 1 pulseelectronics.com 7. Core loss approximation is based on published core data: Core Loss = K1 * (f)1.42 * (K2ΔI)2.57 in mW K1=2.86E-09 (2.50E-09 FOR PG1096.152NL) f = switching frequency in KHz K1 & K2 = core loss factors ΔI= delta I across the component in Ampere K2ΔI=one half of the peak to peak flux density across the component in Gauss 8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac 9. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part number (i.e. PG1096.223NL becomes PG1096.223NLT). Pulse complies with industry standard tape and reel specification EIA481. The tape and reel for this product has a width (W=44.0mm), pitch (Po=36.0mm) and depth (Ko=15.6mm). 10. The core is a conductive material so care should be taken when mounting this component over an exposed via or if the voltage across the terminals exceeds 24V. Trickle current through the core material may generate additional losses and potential overheating. Please contact Pulse to discuss an alternative solution if required. P745.D (08/16) SMT Power Inductors Round wire Coils– PG1096NL series PG1096.XXXNL Mechanicals Schematic 1 2 3 *PIN 3 IS FOR MECHANICAL SUPPORT ONLY AND HAS NO INTERNAL ELECTRICAL CONNECTION Part Number PG1096.152NL PG1096.252NL PG1096.472NL PG1096.682NL PG1096.103NL PG1096.183NL PG1096.223NL PG1096.333NL PG1096.473NL PG1096.683NL PG1096.823NL Lead Width (X) Ref 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 2.3mm H (Height) 13mm P (Pin Pitch) 17.00±1.00mm 14.8mm 17.00±1.70mm Weight..........................34.0 grams (28.0 grams for PG1096.152NL) Tape and Reel....................60/reel Dimensions: Inches mm Unless otherwise specified, all tolerences are ± 2 pulseelectronics.com 0.01 0.25 P745.D (08/16) SMT Power Inductors Round wire Coils– PG1096NL series Inductance Charts PG1096.XXXNL Typical Inductance vs DC Bias Typical Inductance vs DC Bias 10 .152NL@25ºC .152NL@100ºC .252NL@25ºC .252NL@100ºC .472NL@25ºC .472NL@100ºC .682NL@25ºC .682NL@100ºC .103NL@25ºC .103NL@100ºC 8 INDUCTANCE(uH) 7 .183NL@25ºC .183NL@100ºC .223NL@25ºC .223NL@100ºC .333NL@25ºC .333NL@100ºC .473NL@25ºC .473NL@100ºC .683NL@25ºC .683NL@100ºC .823NL@25ºC .823NL@100ºC 80 70 60 INDUCTANCE(uH) 9 6 5 50 40 4 30 3 20 2 1 0 10 20 30 40 50 60 70 80 10 0 5 10 DC Bias (A) 15 20 DC Bias (A) For More Information Pulse Worldwide Headquarters 12220 World Trade Drive San Diego, CA 92128 U.S.A. Pulse Europe Pulse Electronics GmbH Am Rottland 12 58540 Meinerzhagen Germany Pulse China Headquarters B402, Shenzhen Academy of Aerospace Technology Bldg. 10th Kejinan Road High-Tech Zone Nanshan District Shenzhen, PR China 518057 Pulse North China Room 2704/2705 Super Ocean Finance Ctr. 2067 Yan An Road West Shanghai 200336 China Pulse South Asia 135 Joo Seng Road #03-02 PM Industrial Bldg. Singapore 368363 Pulse North Asia 3F, No. 198 Zhongyuan Road Zhongli City Taoyuan County 320 Taiwan R. O. C. Tel: 858 674 8100 Fax: 858 674 8262 Tel: 49 2354 777 100 Fax: 49 2354 777 168 Tel: 86 755 33966678 Fax: 86 755 33966700 Tel: 86 21 62787060 Fax: 86 2162786973 Tel: 65 6287 8998 Fax: 65 6287 8998 Tel: 886 3 4356768 Fax: 886 3 4356823 (Pulse) Fax: 886 3 4356820 (FRE) Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2016. Pulse Electronics, Inc. All rights reserved. 3 pulseelectronics.com P745.D (08/16) 25