PH9085.089NLT

Isolation Power Transformers Toroid Platform SMD PH9085.XXXNL and PM2180.XXXNL Push Pull Converter Transformer Functional insulation for isolated power supply driver 2.5KVrms isolation (380Vrms continuous) Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C Commerical Automotive5 Inductance (1-3) (µH ±35%) PH9085.011NL PM2180.011NL 1020 0.8 30 0.60 0.65 22 1CT : 1CT PH9085.012NL PM2180.012NL 1020 0.6 40 0.85 1.60 22 1CT : 2CT PH9085.021NL PM2180.021NL 1160 1.6 20 0.60 0.35 23.6 2CT : 1CT PH9085.034NL PM2180.034NL 1020 0.6 40 0.60 0.75 22 3CT : 4CT PH9085.035NL PM2180.035NL 1020 0.6 40 0.80 1.20 22 3CT : 5CT PH9085.038NL PM2180.038NL 1020 0.7 40 0.85 2.00 22 3CT : 8CT PH9085.043NL PM2180.043NL 1160 0.8 30 0.60 0.50 23.6 4CT : 3CT PH9085.083NL PM2180.083NL 1160 2.0 15 0.60 0.30 23.6 8CT : 3CT Part Number Leakage Inductance (1-3) with (4-6) shorted (µH MAX) Capacitance (1, 2, 3) to (4, 5, 6) (pF MAX) DCR (1-3) (Ω MAX) DCR (4-6) (Ω MAX) ET MAX (1-3)1 (V-µsec Max) Turns Ratio (1:3) (6:4) Isolated Voltage (Vrms) 2500 PH9085.089NL PM2180.089NL 1160 0.6 40 0.60 0.70 23.6 8CT :9CT Notes: 1. The ET Max is calculated to limit the core loss and temperature rise at 420KHz based on Core Loss (W) = 6.55E-12 * (Frequency in kHz)1.68 * (210 * [ET/ET Max])2.55 a bipolar flux swing of 210mT Peak. Where ET is the applied Volt Second, ET Max is the rated Volt Second for 210mT flux 2. For Push-Pull topology, where the voltage is applied across half the primary winding swing turns, the ET needs to be derated by 50% for the same flux swing. C. To calculate temperature rise, use the following formula: Temperature Rise (°C) 3. The applied ET may need to be further derated for higher frequencies based on the = 140 * (Core Loss(W) + Copper Loss (W)) temperature rise which results from the core and copper losses 4. Continuous isolation voltage confirmed by 125°C/1000hrs accelerated aging with the A. To calculate total copper loss (W), use the following formula: bias voltage applied between primary and secondary windings.. Copper Loss (W) = Irms_Primary2 * DCR_Primary + Irms_Secondary2*DCR_Secondary 5. The PM2180.XXXNL part numbers are AEC-Q200 and IATF16949 certified. The mechanical B. To calculate total core loss (W), use the following formula: dimensions are 100% tested in production but do not necessarily meet aproduct capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Mechanical Schematic PH9085.XXXNL and PM2180.XXXNL Weight ...........................0.365grams Tape & Reel ........................700/reel Tray ......................................55/tray Dimensions: mm Unless otherwise specified, all tolerances are±0.25 1 PulseElectronics.com P759.G (04/21) Isolation Power Transformers Toroid Platform SMD PH9085.XXXNL and PM2180.XXXNL TAPE & REEL INFO Marking Marking K0 A W P1 G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) PART NUMBER PH9085.XXXNLT/PM2180.XXXNLT TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL Ø330 16.4 12 16 6.6 700 APPLICATION PH9085.XXXNL is a series of high isolation power supply transformer drivers. Intended to operate in a fixed duty cycle Push Pull topology, it is a part of a low cost solution for delivering lower power (up to 2W) from a low voltage source. A typical implementation would be an isolated RS-485/RS-232 power supply driver circuit, the design is compatible with the MAXIM™ MAX253 IC. A schematic diagram for the Push Pull converter topology is given below. VIN PH9085/PM2180 VCC D1 V OUT DRIVER IC D2 GND For a fixed 50% duty cycle mode of operation, the output voltage is simply determined by the input voltage and turns ratio. So, with the available turns ratios, a variety of output voltages can be selected. MAXIM is a registered trademark of Maxim Integrated Products. For More Information: Americas - prodinfo_power@pulseelectronics.com | Europe - power-apps-europe@pulseelectronics.com | Asia - power-apps-asia@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2021. Pulse Electronics, Inc. All rights reserved. 2 PulseElectronics.com P759.G (04/21)