PM2201.361NLT

SMT Power Inductors High Current Composite Inductor - PA5001.XXXNLT and PM2201.XXXNLT POWER PRODUCTS IA T F 16 Height: 2.1mm Max Footprint: 4.3mm x 4.3mm Max Current Rating: up to 38Apk Inductance Range: 0.10uH to 2.20uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5001) and Automotive (PM2201) grades 949 Electrical Specifications @ 25°C, Operating Temperature Range -55°C to +155°C Part Number DC Resistance Inductance 100KHz, 0.1V Rated3 Current TYP. MAX. Saturation2 Current uH±20% A mΩ mΩ A K Factor for Core Loss Commerical Automotive6 PA5001.101NLT PM2201.101NLT 0.10 18 2.2 2.42 33 947.4 PA5001.221NLT PM2201.221NLT 0.22 16.8 4.1 4.6 18.8 602.9 PA5001.361NLT PM2201.361NLT 0.36 14.5 5.6 6.3 15.0 442.1 PA5001.401NLT PA5001.471NLT PA5001.561NLT PA5001.601NLT PA5001.721NLT PA5001.102NLT PA5001.122NLT PA5001.152NLT PA5001.182NLT PA5001.222NLT PM2201.401NLT PM2201.471NLT PM2201.561NLT PM2201.601NLT PM2201.721NLT PM2201.102NLT PM2201.122NLT PM2201.152NLT PM2201.182NLT PM2201.222NLT 0.40 0.47 0.56 0.60 0.72 1.00 1.20 1.50 1.80 2.20 14 12.5 12 11.7 10.5 9.6 9 7.6 7 5.6 6.9 7.8 8.4 8.6 10.4 13.3 16.2 21.0 25.0 35.2 7.73 8.58 9.3 9.52 11.6 14.6 17.9 23.5 28 38.7 13.5 13.0 12.6 12.3 10.6 8.8 7.8 7.4 7.0 6.0 442.1 349 288.3 245.6 213.9 189.5 170 - Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. The saturation current is the current at which the initial inductance is guaranteed to drop by no more than 40%. The typical inductance at a specified current can be found on the typical performance curves. 3. The rated current is the DC current required to raise the component temperature by approximately 40�C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 4. The part temperature (ambient+temp rise) should not exceed 155�C under worst case operating conditions. Circuit design, PCB trace size and thickness, airflow and 1 Power.PulseElectronics.com 5. 6. 7. other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. Parts shown in bold are standard catalog parts and are available through sample stock and distribution. Parts in lighter font are available but are not necessarily held in sample stock or distribution and lead times may be longer. Please contact Pulse for availablity. The PM2201.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Special Characteristics P806.C (07/20) SMT Power Inductors High Current Composite Inductor - PA5001.XXXNLT and PM2201.XXXNLT POWER PRODUCTS Mechanical PA5001.XXXNLT and PM2201.XXXNLT A D C L F G E 　XXX 1R2 1602 D/C B H FINAL LAYOUT SUGGESTED PAD LAYOUT Series Mechanical A B C D E F L G H PA5001/PM2201 N/A 4.1±0.2 4.1±0.2 1.9±0.2 3.4±0.3 0.88±0.2 1.6±0.25 3.4 (REF) 1.4 (REF) 3.8 (REF) All Dimensions in mm. TAPE & REEL INFO Chip cavity Blank portions A W Blank portions K0 P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) PA5001/PM2201 TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL Ø330 12.4 8 12 2.3 3000 Typical Performance Curves 100 0.10 80 0.20 80 0.07 60 0.15 60 0.05 40 0.10 40 0.02 20 0.05 20 0 0.00 0.00 0 10 20 30 40 DC CURRENT(A) 2 Power.PulseElectronics.com INDUCTANCE (uH) 0.25 0 5 10 15 20 25 TEMP. RISE(Ȼ) 221NLT 100 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 101NLT 0.12 0 DC CURRENT(A) P806.C (07/20) SMT Power Inductors High Current Composite Inductor - PA5001.XXXNLT and PM2201.XXXNLT POWER PRODUCTS 100 0.32 80 0.36 80 0.24 60 0.27 60 0.16 40 0.18 40 0.08 20 0.09 20 0 0.00 5 10 15 20 25 DC CURRENT(A) 0 5 10 0 561NLT 100 0.60 100 0.48 80 0.48 80 0.36 60 0.36 60 0.24 40 0.24 40 0.12 20 0.12 20 0 0.00 0.00 0 3 6 9 12 15 18 INDUCTANCE (uH) 0.60 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 20 DC CURRENT(A) 471NLT 0 5 10 DC CURRENT(A) 15 20 0 DC CURRENT(A) 601NLT 721NLT 100 0.80 100 0.58 80 0.64 80 0.43 60 0.48 60 0.29 40 0.32 40 0.14 20 0.16 20 0 0.00 0.00 0 5 10 15 20 DC CURRENT(A) 3 Power.PulseElectronics.com INDUCTANCE (uH) 0.72 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 15 TEMP. RISE(Ȼ ) 0 0 3 6 9 12 15 18 TEMP. RISE(Ȼ ) 0.00 INDUCTANCE (uH) 0.45 TEMP. RISE(Ȼ ) 401NLT 100 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 361NLT 0.40 0 DC CURRENT(A) P806.C (07/20) SMT Power Inductors High Current Composite Inductor - PA5001.XXXNLT and PM2201.XXXNLT POWER PRODUCTS 100 0.96 80 1.12 80 0.72 60 0.84 60 0.48 40 0.56 40 0.24 20 0.28 20 0 0.00 0 3 6 9 12 15 0 3 6 12 0 DC CURRENT(A) DC CURRENT(A) 182NLT 152NLT 100 2.00 100 1.44 80 1.60 80 1.08 60 1.20 60 0.72 40 0.80 40 0.36 20 0.40 20 0 0.00 0.00 0 2 4 6 8 10 INDUCTANCE (uH) 1.80 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 9 0 2 4 6 8 10 TEMP. RISE(Ȼ ) 0.00 INDUCTANCE (uH) 1.40 TEMP. RISE(Ȼ ) INDUCTANCE (uH) 100 TEMP. RISE(Ȼ ) 122NLT 102NLT 1.20 0 DC CURRENT(A) DC CURRENT(A) 100 2.00 80 1.50 60 1.00 40 0.50 20 0.00 0 2 4 6 8 10 TEMP. RISE(ȭ ) INDUCTANCE (uH) 222NLT 2.50 0 DC CURRENT(A) 4 Power.PulseElectronics.com P806.C (07/20) SMT Power Inductors High Current Composite Inductor - PA5001.XXXNLT and PM2201.XXXNLT CORE LOSS vs FLUX DENSITY For More Information: Americas - prodinfo_power@pulseelectronics.com | Europe - power-apps-europe@pulseelectronics.com | Asia - power-apps-asia@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2020. Pulse Electronics, Inc. All rights reserved. 5 Power.PulseElectronics.com P806.C (07/20) POWER PRODUCTS