PM2204.122NLT

SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS IA T F 16 Height: 3.1mm Max Footprint: 6.8mm x 6.6mm Max Current Rating: up to 40Apk Inductance Range: 0.18uH to 4.5uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5004) and Automotive (PM2204) grades 949 Electrical Specifications @ 25°C, Operating Temperature Range -55°C to +155°C Part Number DC Resistance Inductance 100KHz, 0.1V Rated3 Current TYP. MAX. Saturation2 Current uH±20% A mΩ mΩ Mechanical D A K Factor for Core Loss Commerical Automotive6 PA5004.181NLT PM2204.181NLT 0.18 32 1.6 1.75 36 358.8 5.30 PA5004.331NLT PM2204.331NLT 0.33 25 2.25 2.5 28 228.3 5.55 PA5004.561NLT PM2204.561NLT 0.56 22 3 3.31 25 167.4 5.30 PA5004.681NLT PA5004.102NLT PA5004.122NLT PA5004.152NLT PA5004.182NLT PA5004.222NLT PA5004.332NLT PA5004.452NLT PM2204.681NLT PM2204.102NLT PM2204.122NLT PM2204.152NLT PM2204.182NLT PM2204.222NLT PM2204.332NLT PM2204.452NLT 0.68 1 1.2 1.5 1.8 2.2 3.3 4.5 20 18 16 15 14 10 8 7 4.7 5.5 6.7 8.3 9.2 11 18.8 23 5.17 6.05 7.4 9.13 10.2 12.2 20.8 25.3 21 18 16 15.5 13 11 9 8 132.2 109.2 93 81 64.4 49.2 5.30 5.20 5.15 5.15 5.10 5.05 5.00 5.00 ±0.3 Notes: 1. 2. 3. 4. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. The saturation current is the current at which the initial inductance is guaranteed to drop by no more than 40%. The typical inductance at a specified current can be found on the typical performance curves. The rated current is the DC current required to raise the component temperature by approximately 40�C. Take note that the components’ performanc varies depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. The part temperature (ambient+temp rise) should not exceed 155�C under worst case operating conditions. Circuit design, PCB trace size and thickness, airflow and 1 Power.PulseElectronics.com 5. 6. 7. other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. Parts shown in bold are standard catalog parts and are available through sample stock and distribution. Parts in lighter font are available but are not necessarily held in sample stock or distribution and lead times may be longer. Please contact Pulse for availablity. The PM2204.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The mechanical dimensions are 100% tested in production but do not necessarily meet a product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. Special Characteristics P805. D (07/20) SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS Mechanical PA5004.XXXNLT and PM2204.XXXNLT A H D C L B F SUGGESTED PAD LAYOUT FINAL LAYOUT Series Mechanical PA5004/PM2204 1.2uH & below 1.5uH & below G E 　XXX D/C A B 6.6±0.2 6.4±0.2 C 2.8±0.2 2.8±0.2 D E F L G H SEE SPEC TABLE 1.4±0.2 2.6±0.25 5.6 (REF) 2.5 (REF) 5.6 (REF) All Dimensions in mm. TAPE & REEL INFO Chip cavity Blank portions A W Blank portions K0 P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) PA5004/PM2204 TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL Ø330 16.4 12 16 3.3 1000 Typical Performance Curves 100 0.20 80 0.36 80 0.15 60 0.27 60 0.10 40 0.18 40 0.05 20 0.09 20 0.00 0 10 2 20 30 DC CURRENT (A) 40 50 Power.PulseElectronics.com 0 Inductance （uH） 0.45 0.00 0 7 14 21 28 35 TEMP. RISE (°C) 331NLT 100 TEMP. RISE (°C) Inductance （uH） 181NLT 0.25 0 DC CURRENT (A) P805. D (07/20) SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS 100 0.56 80 0.72 80 0.42 60 0.54 60 0.28 40 0.36 40 0.14 20 0.18 20 0 0.00 1.5 100 1.5 100 1.2 80 1.2 80 0.9 60 0.9 60 0.6 40 0.6 40 0.3 20 0.3 20 6 12 18 DC CURRENT (A) 24 30 0 5 10 0 5 10 15 DC CURRENT (A) 25 152NLT 2.0 Inductance （uH） 20 80 1.2 60 0.8 40 0.4 20 0 3 6 3 9 12 15 18 DC CURRENT (A) Inductance （uH） 0.0 30 0 21 24 27 Power.PulseElectronics.com 0 0 5 10 15 DC CURRENT (A) 20 25 0 182NLT 100 1.6 0.0 TEMP. RISE (°C) 0 Inductance （uH） 0.0 25 122NLT TEMP. RISE (°C) Inductance （uH） 102NLT 15 20 DC CURRENT (A) TEMP. RISE (°C) 0 2.5 100 2.0 80 1.5 60 1.0 40 0.5 20 0.0 0 4 8 12 DC CURRENT (A) 16 20 TEMP. RISE (°C) 0.00 Inductance （uH） 0.90 TEMP. RISE (°C) 681NLT 100 TEMP. RISE (°C) Inductance （uH） 561NLT 0.70 0 P805. D (07/20) SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS 100 2.4 80 3.2 80 1.8 60 2.4 60 1.2 40 1.6 40 0.6 20 0.8 20 0 0.0 0.0 0 4 8 12 DC CURRENT (A) 16 20 Inductance （uH） 4.0 TEMP. RISE (°C) Inductance （uH） 100 0.0 2.5 5.0 7.5 DC CURRENT (A) 10.0 12.5 TEMP. RISE (°C) 332NLT 222NLT 3.0 0 100 4.8 80 3.6 60 2.4 40 1.2 20 0.0 0 2.5 4 5 7.5 DC CURRENT (A) 10 TEMP. RISE (°C) Inductance （uH） 452NLT 6.0 0 12.5 Power.PulseElectronics.com P805. D (07/20) SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT CORE LOSS vs FLUX DENSITY 2.0 200KHz 1.8 400KHz 1.6 600KHz 800KHz Core Loss (W) 1.4 1000KHz 1.2 1400KHz 1800KHz 1.0 0.8 0.6 0.4 0.2 0.0 0 500 1,000 1,500 2,000 2,500 Bp-p (Gauss) Bp-p = K *L(uH) *delta I(A) For More Information: Americas - prodinfo_power@pulseelectronics.com | Europe - power-apps-europe@pulseelectronics.com | Asia - power-apps-asia@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2020. Pulse Electronics, Inc. All rights reserved. 5 Power.PulseElectronics.com P805. D (07/20) POWER PRODUCTS