B39311B3577U310

SAW Components Data Sheet B3577 SAW Components B3577 Low-loss Filter 311,06 MHz Data Sheet Ceramic package QCC8C Features ■ RF low-loss filter for remote control receivers ■ Package for Surface Mounted Technology ■ ■ ■ ■ ■ (SMT) Balanced and unbalanced operation possible Passivation layer: Protec AEC-Q200 qualified component family Compliant to EU RoHs Directive (2002/95/EC) Lead free soldering compatible with J - STD20C Terminals typ. dimensions in mm, approx. weight 0,1 g ■ Ni, gold plated Pin configuration 1 2 5 6 4,8 Input Ground Input Output Output Ground Case - Ground 3,7 to be grounded Type Ordering code B3577 B39311-B3577-U310 Marking and package according to C61157-A7-A56 Packing according to F61074-V8169-Z000 Electrostactic Sensitive Device (ESD) Maximum ratings Operable temperature range TA Storage temperature range DC voltage Source power Tstg VDC PS –45/+120 ˚C –45/+120 0 10 ˚C V dBm 2 source impedance 50 Ω Sep 09, 2005 SAW Components B3577 Low-loss Filter 311,06 MHz Data Sheet Characteristics Reference temperature: Terminating source impedance: Terminating load impedance: TA = -40 ... 95 ˚C ZS = 50 Ω and matching network ZL = 50 Ω and matching network min. typ. max. — 311,06 — Minimum insertion attenuation αmin 310,94 ... 311,18 MHz — 2,0 3,0 dB Pass band (relative to αmin) 310,94 ... 311,18 MHz 310,91 ... 311,21 MHz — — 1,0 2,0 2,0 3,0 dB dB fC Center frequency (center frequency between 3 dB points) Relative attenuation (relative to αmin) 10,00 ... 290,00 290,00 ... 306,00 306,00 ... 310,10 312,00 ... 313,50 320,00 ... 396,00 550,00 ...1000,00 MHz αrel MHz MHz MHz MHz MHz MHz Impedance for pass band matching Input: ZIN = RIN || CIN Output: ZOUT = ROUT || COUT 40 35 20 15 35 45 45 40 26 21 40 60 — — — — — — dB dB dB dB dB dB — 353 || 3,30 343 || 3,30 — Ω || pF — Ω || pF — Temperature coefficient of frequency 1) TCf — –0,03 — ppm/K2 Frequency inversion point T0 10 — 30 °C 1)Temperature dependence of fC: fC(TA) = fC(T0) (1 + TCf(TA – T0)2) 3 Sep 09, 2005 SAW Components B3577 Low-loss Filter 311,06 MHz Data Sheet Matching network to 50 Ω (element values depend on pcb layout and equivalent circuit) Ls1 = 56 nH Ls2 = 56 nH Minimising the crosstalk For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with a good RF layout. The major crosstalk mechanism is caused by the “ground-loop” problem. Grounding loops are created if input-and output transducer GND are connected on the top-side of the PCB and fed to the system grounding plane by a common via hole. To avoid the common ground path, the ground pin of the input- and output transducer are fed to the system ground plane (bottom PCB plane) by their own via hole. The transducers’ grounding pins should be isolated from the upper grounding plane. A common GND inductivity of 0.5nH degrades the ultimate rejection (crosstalk) by 20dB. The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown here. In this PCB layout the grounding loops are minimised to realise good ultimate rejection. Optimised PCB layout for SAW filters in QCC8C package, pinning 2,5 (top side, scale 1:1) The bottom side is a copper plane (system ground area). The input and output grounding pins are isolated and connected to the common ground by separated via holes. For good contact of the upper grounding area with the lower side it is necessary to place enough via holes. 4 Sep 09, 2005 SAW Components B3577 Low-loss Filter 311,06 MHz Data Sheet Normalized frequency response Normalized frequency response (wideband) 5 Sep 09, 2005 SAW Components B3577 Low-loss Filter 311,06 MHz Data Sheet Published by EPCOS AG Surface Acoustic Wave Components Division, SAW CE AE PD P.O. Box 80 17 09, D-81617 München  EPCOS AG 2005. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 6 Sep 09, 2005