B39700B3605Z510

SAW filters for infrastructure systems Series/Type: B3605 The following products presented in this data sheet are being withdrawn. Ordering Code Substitute Product Date of Withdrawal B39700B3605Z510 B39700B5018Z510 2011-04-01 Deadline Last Orders 2011-06-30 Last Shipments 2011-09-30 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.  EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company. SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Ceramic package QCC12 Features ● ● ● ● High performance IF bandpass filter Constant group delay Hermetically sealed ceramic package Filter surface passivated Terminals ● Gold plated Dimensions in mm, approx. weight 0,4 g Pin configuration 11 1 5 7 2, 3, 8, 9 4, 6, 10, 12 Input Input - ground Output Output - ground Case - ground Ground 11 5 1 7 2,3,8,9 Type Ordering code B3605 B39700-B3605-Z510 Marking and Package according to C61157-A7-A55 Packing according to F61074-V8163-Z000 Electrostatic Sensitive Device (ESD) Maximum ratings Operable temperature range Storage temperature range DC voltage Source power T Tstg VDC Ps – 40/+ 85 – 40/+ 85 0 10 2 ˚C ˚C V dBm Jul 09, 2003 source impedance 50 Ω SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Characteristics Operating temperature: Terminating source impedance: Terminating load impedance: Group delay aperture T = -40 ˚C... 85 ˚C ZS = 50 Ω and matching circuit(Unbalanced) ZL = 50 Ω and matching circuit(Unbalanced) 80 kHz min. typ. max. Center frequency (Center between 6dB points) Insertion attenuation at fC fC 69,50 αC — 9,6 10,8 dB Amplitude ripple (p-p) ∆α — 0,6 1,0 dB — 15,0 18,0 ˚ 8,1 9,1 — 8,3 9,3 12,8 — — 13,2 MHz MHz MHz 43 34 28 35 47 38 36 41 — — — — dB dB dB dB — µs ns 67,00 ... 73,00 MHz 70,00 70,50 MHz ∆ϕ Phase ripple (p-p) 65,50 ... 74,50 MHz Pass bandwidth αrel ≤ 1 dB αrel ≤ 3 dB αrel ≤ 30 dB Relative attenuation (relative to αC) 50,00 ... 62,50 62,50 ... 63,00 77,00 ... 77,50 77,50 ... 90,00 B1dB B3dB B30dB αrel MHz MHz MHz MHz τC Group delay at fC — 1,1 ∆τ Group delay ripple (p-p) 65,50 ... 74,50 MHz TCf Temperature coefficient of frequency 3 — 80 200 — – 87 — Jul 09, 2003 ppm/K SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Characteristics Operating temperature: Terminating source impedance: Terminating load impedance: Group delay aperture T = -40 ˚C... 85 ˚C ZS = 50 Ω and matching circuit(Balanced) ZL = 50 Ω and matching circuit(Balanced) 80 kHz min. Center frequency (Center between 6dB points) Insertion attenuation at fC typ. max. fC 69,50 αC — 9,8 10,8 dB — 0,6 1,0 dB — 17,0 20,0 ˚ 8,1 9,1 — 8,3 9,3 12,8 — — 13,2 MHz MHz MHz 43 34 26 35 45 38 35 38 — — — — dB dB dB dB — µs ns 70,00 70,50 MHz ∆α Amplitude ripple (p-p) 67,00 ... 73,00 MHz 65,50 ... 74,50 MHz ∆ϕ Phase ripple (p-p) Pass bandwidth αrel ≤ 1 dB αrel ≤ 3 dB αrel ≤ 30 dB Relative attenuation (relative to αC) 50,00 ... 62,50 62,50 ... 63,00 77,00 ... 77,50 77,50 ... 90,00 B1dB B3dB B30dB αrel MHz MHz MHz MHz τC Group delay at fC — 1,1 ∆τ Group delay ripple (p-p) 65,50 ... 74,50 MHz TCf Temperature coefficient of frequency 4 — 80 200 — – 87 — Jul 09, 2003 ppm/K SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Matching circuit: unbalanced - unbalanced Ls1=180nH Ls3=18nH Ls2=100nH Ls4=270nH Matching circuit: balanced - balanced Ls1=180nH Ls3=10nH Ls2=56nH Ls4=270nH Note: Component values depend on PCB layout. 5 Jul 09, 2003 SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Normalized frequency response(unbalanced-unbalanced) Normalized frequency response 6 Jul 09, 2003 SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Normalized frequency response(balanced-balanced) Normalized frequency response 7 Jul 09, 2003 SAW Components B3605 Low-Loss Filter 70,00 MHz Data Sheet Attachment 1) For a duration < 50 ms source power may be raised to 20 dBm. 2) Pyroelectric pulse amplitude < 50 mV. 3) If external impedances are the same, input port and output port may be reversed without any changes of the performance. Published by EPCOS AG Surface Acoustic Wave Components Division, SAW MC IS P.O. Box 80 17 09, 81617 Munich, GERMANY  EPCOS AG 2003. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 8 Jul 09, 2003