B39871B3571U310

SAW Components Data Sheet B3571 SAW Components B3571 Low-loss Filter 868,60 MHz Data Sheet Ceramic package QCC8C Features ■ RF low-loss filter for remote control receivers ■ Package for Surface Mounted Technology (SMT) Terminals ■ Ni, gold plated typ. dimensions in mm, approx. weight 0,1 g Pin configuration 2 1,3 6 5,7 4,8 Input Input Ground Output Output Ground Case - Ground Type Ordering code B3571 B39871-B3571-U310 Marking and package according to C61157-A7-A56 Packing according to F61074-V8070-Z000 Electrostactic Sensitive Device (ESD) Maximum ratings Operable temperature range Storage temperature range DC voltage Source power TA Tstg VDC PS –45/+90 ˚C –45/+90 0 0 ˚C V dBm 2 source impedance 50 Ω May 09, 2001 SAW Components B3571 Low-loss Filter 868,60 MHz Data Sheet Characteristics Reference temperature: Terminating source impedance: Terminating load impedance: TA = 25 ˚C ZS = 50 Ω and matching network ZL = 50 Ω and matching network min. typ. max. — 868,69 — MHz Minimum insertion attenuation αmin 868,00 ... 869,38 MHz — 3,1 4,6 dB Pass band (relative to αmin) 868,00 ... 869,38 MHz 867,92 ... 869,46 MHz — — 1,5 2,0 3,0 6,0 dB dB 50 33 30 20 17 30 33 55 38 35 25 22 35 38 — — — — — — — dB dB dB dB dB dB dB — 226 || 2,30 222 || 2,20 — Ω || pF — — Ω || pF fC Center frequency (center frequency between 3 dB points) Relative attenuation (relative to αmin) 10,00 ... 700,00 700,00 ... 830,00 830,00 ... 858,00 858,00 ... 866,40 871,00 ... 880,00 880,00 ... 910,00 910,00 ...1000,00 αrel MHz MHz MHz MHz MHz MHz MHz Impedance for pass band matching 2) Input: ZIN = RIN || CIN Output: ZOUT = ROUT || COUT Temperature coefficient of frequency 1) TCf — –0,03 — ppm/K2 Frequency inversion point T0 — 25 — °C 1)Temperature dependence of fC: fC(TA) = fC(T0) (1 + TCf(TA – T0)2) 2) Impedance for passband matching bases on an ideal, perfect matching of the SAW filter to source- and to load impedance (here 50 Ohm). After the SAW filter is removed and input impedance into the input matching / output matching network is calculated. The conjugate complex value of these characteristic impedances are the input and output impedances for flat passband. For more details, we refer to EPCOS application note #4. 3 May 09, 2001 SAW Components B3571 Low-loss Filter 868,60 MHz Data Sheet Matching network to 50 Ω (element values depend on pcb layout and equivalent circuit) Cp1 = 3,3 pF Ls2 = 15 nH Ls3 = 15 nH Cp4 = 3,3 pF Minimising the crosstalk For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with a good RF layout. Grounding pins for input transducer are pin 1,3 and for output transducer 5,7. Close to those pins via holes (through holes) should be placed to achieve a low impedance path to system ground. If a grounding plane at the top side of the PCB is present, the grounding plane can be connected to pin 1,3,5,7 at the top side too. The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown here. Optimised PCB layout for SAW filters in QCC8C package, pinning 2,6 (top side, scale 1:1) The bottom side is a copper plane (system ground area). For good contact of the upper grounding area with the lower side it is necessary to place enough via holes. 4 May 09, 2001 SAW Components B3571 Low-loss Filter 868,60 MHz Data Sheet Normalized frequency response Normalized frequency response (wideband) 5 May 09, 2001 SAW Components B3571 Low-loss Filter 868,60 MHz Data Sheet Published by EPCOS AG Surface Acoustic Wave Components Division, SAW CE AE PD P.O. Box 80 17 09, D-81617 München  EPCOS AG 2001. All Rights Reserved. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. For questions on technology, prices and delivery please contact the sales offices of EPCOS AG or the international representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our sales offices. 6 May 09, 2001