B39881B8013P810

RF360 Europe GmbH A Qualcomm – TDK Joint Venture SAW components SAW duplexer Small cell & femtocell LTE band 5 Series/type: B8013 Ordering code: B39881B8013P810 Date: September 14, 2017 Version: 2.8 RF360 products mentioned within this document are offered by RF360 Europe GmbH and other subsidiaries of RF360 Holdings Singapore Pte. Ltd. (collectively, the “RF360 Subsidiaries”). RF360 Holdings Singapore Pte. Ltd. is a joint venture of Qualcomm Global Trading Pte. Ltd. and EPCOS AG. RF360 Europe GmbH, Anzinger Str. 13, München, Germany © 2017 RF360 Europe GmbH and/or its affiliated companies. All rights reserved. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet These materials, including the information contained herein, may be used only for informational purposes by the customer. The RF360 Subsidiaries assume no responsibility for errors or omissions in these materials or the information contained herein. The RF360 Subsidiaries reserve the right to make changes to the product(s) or information contained herein without notice. The materials and information are provided on an AS IS basis, and the RF360 Subsidiaries assume no liability and make no warranty or representation, either expressed or implied, with respect to the materials, or any output or results based on the use, application, or evaluation of such materials, including, without limitation, with respect to the non-infringement of trademarks, patents, copyrights or any other intellectual property rights or other rights of third parties. No use of this documentation or any information contained herein grants any license, whether express, implied, by estoppel or otherwise, to any intellectual property rights, including, without limitation, to any patents owned by QUALCOMM Incorporated or any of its subsidiaries. Not to be used, copied, reproduced, or modified in whole or in part, nor its contents revealed in any manner to others without the express written permission of RF360 Europe GmbH. Qualcomm and Qualcomm RF360 are trademarks of Qualcomm Incorporated, registered in the United States and other countries. RF360 is a trademark of Qualcomm Incorporated. Other product and brand names may be trademarks or registered trademarks of their respective owners. This technical data may be subject to U.S. and international export, re-export, or transfer (“export”) laws. Diversion contrary to U.S. and international law is strictly prohibited. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet Table of contents 1 Application......................................................................................................................................... 4 2 Features............................................................................................................................................ 4 3 Package............................................................................................................................................ 5 4 Pin configuration................................................................................................................................ 5 5 Matching circuit................................................................................................................................. 6 6 Characteristics................................................................................................................................... 7 7 Maximum ratings............................................................................................................................. 13 8 Transmission coefficients................................................................................................................. 14 9 Reflection coefficients...................................................................................................................... 17 10 EVMs............................................................................................................................................. 18 11 Packing material............................................................................................................................ 20 12 Marking.......................................................................................................................................... 23 13 Soldering profile............................................................................................................................. 24 14 Annotations................................................................................................................................... 25 15 Cautions and warnings.................................................................................................................. 26 Important notes................................................................................................................................. 27 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 1 Application  Low-loss SAW duplexer for LTE small cell & femtocell systems ( Band 5)  Usable pass band 25MHz  Rx=uplink=824-849MHz  Tx=downlink=869-894MHz 2          Features Industrial grade qualified family Package size 2.5±0.1 mm × 2.0±0.1 mm Package height 0.5 mm (max.) Approximate weight 1 g RoHS compatible Package for Surface Mount Technology (SMT) Ni/Au-plated terminals Electrostatic Sensitive Device (ESD) Moisture Sensitivity Level 2a (MSL2a) Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 27 Figure 1: Picture of component with example of product marking. September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 3 Package 4 Pin configuration  1 TX  3 RX  6 ANT  2, 4, 5, 7, Ground 8, 9 Figure 2: Drawing of package with package height A = 0.5 mm (max.). See Sec. Package information (p. 26). Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 5 Matching circuit  Lp6 = 8.7 nH Figure 3: Schematic of matching circuit. Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 6 6.1 Characteristics TX – ANT Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −10 °C ... +85 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics TX – ANT min. typ. max. for TSPEC @ +25 °C for TSPEC Center frequency fC Average insertion attenuation — 881.5 — MHz αINT,avg2) 869... 874 MHz — 1.9 2.5 dB 874... 889 MHz — 1.5 2.5 dB 889... 894 MHz — 1.7 2.5 dB — 1.9 2.53) dB — 0.6 1.34) dB Maximum insertion attenuation αmax 869... 894 MHz Amplitude ripple (p-p) Δα 869... 894 MHz Maximum VSWR VSWRmax @ TX port 869... 894 MHz — 1.9 2.15) @ ANT port 869... 894 MHz — 1.8 2.15) — 1.4 3.5 % Maximum error vector magnitude EVMmax6) 871.4... 891.6 MHz Minimum attenuation 1) 2) 3) 4) 5) 6) αmin 824... 849 MHz 52 59 — dB 1574.4... 1576.4 MHz 45 58 — dB 1602.5... 1615.5 MHz 35 59 — dB 1710... 1788 MHz 40 59 — dB 1850... 1910 MHz 40 57 — dB 1920... 1980 MHz 40 55 — dB 2400... 2484 MHz 21 50 — dB 2607... 2682 MHz 21 47 — dB 3476... 3576 MHz 21 49 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Specification for ILmax is 2.6dB for −20 °C ... +85 °C. Specification for AR is 1.4dB for −20 °C ... +85 °C. Specification for VSWR is 2.2 for −20 °C ... +85 °C. Error Vector Magnitude (EVM) based on definition in 3GPP TS 25.141. Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −40 °C ... +95 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics TX – ANT min. typ. max. for TSPEC @ +25 °C for TSPEC Center frequency fC Average insertion attenuation MHz MHz — 1.9 3.0 dB 874... 889 MHz — 1.5 3.0 dB 889... 894 MHz — 1.7 3.0 dB — 1.9 3.0 dB — 0.6 1.7 dB — 1.9 2.3 — 1.8 2.3 — 1.4 4.0 % αmax 869... 894 MHz Δα 869... 894 MHz Maximum VSWR VSWRmax @ TX port 869... 894 MHz @ ANT port 869... 894 MHz Maximum error vector magnitude EVMmax 871.4... 891.6 3) MHz Minimum attenuation 3) — 869... 874 Amplitude ripple (p-p) 2) 881.5 αINT,avg2) Maximum insertion attenuation 1) — αmin 824... 849 MHz 52 59 — dB 1574.4... 1576.4 MHz 45 58 — dB 1602.5... 1615.5 MHz 35 59 — dB 1710... 1788 MHz 40 59 — dB 1850... 1910 MHz 40 57 — dB 1920... 1980 MHz 40 55 — dB 2400... 2484 MHz 21 50 — dB 2607... 2682 MHz 21 47 — dB 3476... 3576 MHz 21 49 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Error Vector Magnitude (EVM) based on definition in 3GPP TS 25.141. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 6.2 ANT – RX Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −10 °C ... +85 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics ANT – RX min. typ. max. for TSPEC @ +25 °C for TSPEC Center frequency fC Average insertion attenuation — 836.5 — MHz α 2) INT,avg 824... 829 MHz — 2.1 3.1 dB 829... 844 MHz — 1.8 3.1 dB 844... 849 MHz — 1.7 3.1 dB — 2.6 3.13) dB — 1.3 1.84) dB Maximum insertion attenuation αmax 824... 849 MHz Amplitude ripple (p-p) Δα 824... 849 MHz Maximum VSWR VSWRmax @ ANT port 824... 849 MHz — 1.9 2.35) @ RX port 824... 849 MHz — 2.0 2.35) — 3.0 4.5 % Maximum error vector magnitude EVMmax6) 826.4... 846.6 MHz Minimum attenuation 1) 2) 3) 4) 5) 6) αmin 869... 894 MHz 50 57 — dB 1648... 1698 MHz 25 51 — dB 1840... 1870 MHz 25 48 — dB 1930... 1990 MHz 25 46 — dB 2110... 2170 MHz 25 45 — dB 2400... 2484 MHz 25 42 — dB 2472... 2547 MHz 25 41 — dB 3296... 3396 MHz 20 39 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Specification for ILmax is 3.2dB for −20 °C ... +85 °C. Specification for AR is 1.9dB for −20 °C ... +85 °C. Specification for VSWR is 2.4 for −20 °C ... +85 °C. Error Vector Magnitude (EVM) based on definition in 3GPP TS 25.141. Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −40 °C ... +95 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics ANT – RX min. typ. max. for TSPEC @ +25 °C for TSPEC Center frequency fC Average insertion attenuation MHz MHz — 2.1 3.8 dB 829... 844 MHz — 1.8 3.8 dB 844... 849 MHz — 1.7 3.8 dB — 2.6 3.8 dB — 1.3 2.5 dB — 1.9 2.5 — 2.0 2.5 — 3.0 5.0 % αmax 824... 849 MHz Δα 824... 849 MHz Maximum VSWR VSWRmax @ ANT port 824... 849 MHz @ RX port 824... 849 MHz Maximum error vector magnitude EVMmax 826.4... 849 3) MHz Minimum attenuation 3) — 824... 829 Amplitude ripple (p-p) 2) 836.5 αINT,avg2) Maximum insertion attenuation 1) — αmin 869... 894 MHz 50 55 — dB 1648... 1698 MHz 25 51 — dB 1840... 1870 MHz 25 48 — dB 1930... 1990 MHz 25 46 — dB 2110... 2170 MHz 25 45 — dB 2400... 2484 MHz 25 42 — dB 2472... 2547 MHz 25 41 — dB 3296... 3396 MHz 20 39 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Error Vector Magnitude (EVM) based on definition in 3GPP TS 25.141. Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 6.3 TX – RX Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −10 °C ... +85 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics TX – RX min. typ. max. for TSPEC @ +25 °C for TSPEC Average isolation αINT,avg2) 824... 849 MHz 52 58 — dB 869... 894 MHz 53 61 — dB Minimum isolation 1) 2) αmin 824... 849 MHz 52 58 — dB 869... 894 MHz 53 56 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet Temperature range for specification TX terminating impedance ANT terminating impedance RX terminating impedance TSPEC ZTX ZANT ZRX = = = = −40 °C ... +95 °C 50 Ω 50 Ω with par. 8.7 nH1) 50 Ω Characteristics TX – RX min. typ. max. for TSPEC @ +25 °C for TSPEC Average isolation αINT,avg2) 824... 849 MHz 52 58 — dB 869... 894 MHz 52 61 — dB Minimum isolation 1) 2) αmin 824... 849 MHz 52 56 — dB 869... 894 MHz 52 56 — dB See Sec. Matching circuit (p. 6). Integrated over 5 MHz. Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 7 Maximum ratings Operable temperature TOP = −40 °C ... +95 °C Storage temperature TSTG1) = −40 °C ... +95 °C DC voltage |VDC|2) = 0 V ESD voltage Input power VESD3) = 100 V Machine model. VESD4) = 250 V Human body model. PIN @ TX port: 871.5 ... 891.5 MHz 28 dBm5), 6) 5 MHz LTE downlink signal for 100000 h @ 55 °C. PIN 28 dBm average 39 dBm peak. Source and load impedance 50 Ω. @ TX port: other frequency ranges 10 dBm Source and load impedance 50Ω. POUT7) = 24 dBm Continuous wave for 100000 h @ 55 °C. Source and load impedance 50Ω. Operating lifetime with output power at antenna @ ANT port: 871.5 ... 891.5 MHz 1) 2) 3) 4) 5) 6) 7) Not valid for packaging material. Storage temperature for packaging material is −25 °C to +40 °C. In case of applied DC voltage blocking capacitors are mandatory. According to JESD22-A115B (MM – Machine Model), 10 negative & 10 positive pulses. According to JESD22-A114F (HBM – Human Body Model), 1 negative & 1 positive pulse. Expected lifetime according to accelerated power durability tests, and wear out models. TSPEC is the ambient temperature of the PCB at component position. Specified min./max values from section 6 "characteristics" for maximum input power 28dBm are valid for temperature up to 55°C. According to accelerated high temperature operating life (HTOL) test. Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 8 8.1 Transmission coefficients TX – ANT Figure 4: Attenuation TX – ANT. Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 8.2 ANT – RX Figure 5: Attenuation ANT – RX. Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 8.3 TX – RX Figure 6: Isolation TX – RX. Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 9 Reflection coefficients Figure 7: Reflection coefficient at TX port. Figure 8: Reflection coefficient at ANT port. Figure 9: Reflection coefficient at RX port. Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 10 EVMs 10.1 TX – ANT Figure 10: Error vector magnitude TX – ANT. Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 10.2 ANT – RX Figure 11: Error vector magnitude ANT – RX. Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 11 Packing material 11.1 Tape Figure 12: Drawing of tape (first-angle projection) with tape dimensions according to Table 1. A0 2.25±0.05 mm E2 6.25 mm (min.) B0 2.75±0.05 mm F 3.5±0.05 mm D0 1.5+0.1/−0 mm G 0.75 mm (min.) D1 1.0 mm (min.) K0 0.6±0.05 mm E1 1.75±0.1 mm P0 4.0±0.1 mm P1 4.0±0.1 mm P2 2.0±0.05 mm T 0.25±0.03 mm W 8.0+0.3/−0.1 mm Table 1: Tape dimensions. Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 11.2 Reel with diameter of 180 mm Figure 13: Drawing of reel (first-angle projection) with diameter of 180 mm. Figure 14: Drawing of moisture barrier bag (MBB) for reel with diameter of 180 mm. Please read Cautions and warnings and Important notes at the end of this document. Page 21 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet Figure 15: Drawing of folding box for reel with diameter of 180 mm. Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 12 Marking Products are marked with product type number and lot number encoded according to Table 2:  Type number: The 4 digit type number of the ordering code, is encoded by a special BASE32 code into a 3 digit marking. e.g., B3xxxxB1234xxxx, Example of decoding type number marking on device 16J => 1 x 322 + 6 x 321 + 18 (=J) x 320 = The BASE32 code for product type B8013 is 7TD. in decimal code. 1234 1234  Lot number: The last 5 digits of the lot number, e.g., are encoded based on a special BASE47 code into a 3 digit marking. Example of decoding lot number marking on device 5UY 5 x 472 + 27 (=U) x 471 + 31 (=Y) x 470 Adopted BASE32 code for type number Decimal Base32 Decimal Base32 value code value code 0 0 16 G 1 1 17 H 2 2 18 J 3 3 19 K 4 4 20 M 5 5 21 N 6 6 22 P 7 7 23 Q 8 8 24 R 9 9 25 S 10 A 26 T 11 B 27 V 12 C 28 W 13 D 29 X 14 E 30 Y 15 F 31 Z => = 12345, in decimal code. 12345 12345 Adopted BASE47 code for lot number Decimal Base47 Decimal Base47 value code value code 0 0 24 R 1 1 25 S 2 2 26 T 3 3 27 U 4 4 28 V 5 5 29 W 6 6 30 X 7 7 31 Y 8 8 32 Z 9 9 33 b 10 A 34 d 11 B 35 f 12 C 36 h 13 D 37 n 14 E 38 r 15 F 39 t 16 G 40 v 17 H 41 \ 18 J 42 ? 19 K 43 { 20 L 44 } 21 M 45 < 22 N 46 > 23 P Table 2: Lists for encoding and decoding of marking. Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 13 Soldering profile The recommended soldering process is in accordance with IEC 60068-2-58 – 3rd edit and IPC/JEDEC J-STD-020B. ramp rate ≤ 3 K/s preheat 125 °C to 220 °C, 150 s to 210 s, 0.4 K/s to 1.0 K/s T > 220 °C 30 s to 70 s T > 230 °C min. 10 s T > 245 °C max. 20 s T ≥ 255 °C – peak temperature Tpeak 250 °C +0/-5 °C wetting temperature Tmin 230 °C +5/-0 °C for 10 s ± 1 s cooling rate ≤ 3 K/s soldering temperature T measured at solder pads Table 3: Characteristics of recommended soldering profile for lead-free solder (Sn95.5Ag3.8Cu0.7). Figure 16: Recommended reflow profile for convection and infrared soldering – lead-free solder. Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 14 Annotations 14.1 Matching coils See TDK inductor pdf-catalog http://www.tdk.co.jp/tefe02/coil.htm#aname1 and Data Library for circuit simulation http://www.tdk.co.jp/etvcl/index.htm. 14.2 RoHS compatibility ROHS-compatible means that products are compatible with the requirements according to Art. 4 (substance restrictions) of Directive 2011/65/EU of the European Parliament and of the Council of June 8th, 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment ("Directive") with due regard to the application of exemptions as per Annex III of the Directive in certain cases. 14.3 Scattering parameters (S-parameters) The pin/port assignment is available in the headers of the S-parameter files. Please contact your local RF360 sales office. 14.4 Ordering codes and packing units Ordering code Packing unit B39881B8013P810 5000 pcs Table 4: Ordering codes and packing units. Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 27 September 14, 2017 May contain US and international export controlled information. RF360 RF360Europe EuropeGmbH GmbH SAW components B8013 SAW duplexer 836.5 / 881.5 MHz Data sheet 15 Cautions and warnings 15.1 Display of ordering codes for RF360 products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of RF360, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.rf360jv.com/orderingcodes. 15.2 Material information Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our sales offices. For information on recycling of tapes and reels please contact one of our sales offices. 15.3 Moldability Before using in overmolding environment, please contact your local RF360 sales office. 15.4 Package information Landing area The printed circuit board (PCB) land pattern (landing area) shown is based on RF360 internal development and empirical data and illustrated for example purposes, only. As customers' SMD assembly processes may have a plenty of variants and influence factors which are not under control or knowledge of RF360, additional careful process development on customer side is necessary and strongly recommended in order to achieve best soldering results tailored to the particular customer needs. Dimensions Unless otherwise specified all dimensions are understood using unit millimeter (mm). Dimensions do not include burrs. Projection method Unless otherwise specified first-angle projection is applied. Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 27 September 14, 2017 May contain US and international export controlled information. RF360 Europe GmbH Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, RF360 Europe GmbH and its affiliates are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an RF360 product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.rf360jv.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. Please read Cautions and warnings and Important notes at the end of this document. Page 27 of 27 September 14, 2017 May contain US and international export controlled information