BIM3G-869-128-5V

Hartcran House, 231 Kenton Lane, Harrow, Middlesex, HA3 8RP, England Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233, www.radiometrix.com BiM2/BiM3G PRELIMINARY Issue 1, 11 November 2009 433 / 868MHz FM Data Transceiver The BIM2/3G data radio module is a PLL synthesiser based miniature PCB mounting UHF radio transceiver which enable the simple implementation of a wireless data link at up to 128 kbps at distances up to 75 metres in-building and 300 metres open ground. Features ! ! ! ! Data rates up to 128 kbps Figure 1: BIM3G-869-64-5V Usable range up to 300 m Versions available on 433.92MHz, 434.42MHz and 868MHz band Fully screened Low profile with small footprint Designed for compliance with EN 300 220-3 (radio) and EN 301 489-3 (EMC) standards ! ! Available for operation at 433.92MHz, 434.42MHz and 868MHz band in the UK and Europe, these modules combine full screening with extensive internal filtering to ensure EMC compliance by minimising spurious radiations and susceptibilities. The BIM2/3G module will suit one-to-one and multi-node wireless links in applications. Because of their small size and low power requirements, the module is ideal for use in portable, battery-powered applications such as hand-held terminals. Applications ! ! ! ! ! ! ! Data loggers EPOS equipment, barcode scanners, belt clip printers Audience response systems In-building environmental monitoring and control Security and fire alarms Restaurant ordering systems Vehicle data up/download Technical Summary ! ! ! Crystal-locked PLL, FM modulated at up to 128 Kbps +10dBm on 433.92MHz and 868MHz (Dependent on version) High efficiency, >30%, DC to RF 2nd harmonic, > -60dBc Single conversion FM superhet receiver SAW front end filter gives >50dB image rejection Sensitivity: -102dBm sensitivity @ 1ppm BER, 64kbps version -108dBm sensitivity @ 1ppm BER, 15kbps version TBA dBm sensitivity @ 1ppm BER, 128kbps version RSSI output with 60dB range Extremely low LO leakage, -125dBm typical Supply: +5V (± 10%) Current consumption: 10mA (typ.) Size: 33 x 23 x 5mm ! ! ! ! ! ! ! ! ! Evaluation platforms: Universal Evaluation Kit, NBEK + DIL carrier Radiometrix Ltd, BIM2/3G Data Sheet page 1 Functional overview The transmit section of the BiM2/3G consists of a frequency modulated crystal locked PLL feeding a buffer amplifier and RF filter. A Tx select line controls operation. The transmitter achieves full RF output typically within 1ms of this line being pulled low. Modulation is applied at the TXD input and may be either a serial digital stream toggling between 0V and 5V (digital drive) or a high level analogue waveform with the same peak limits (linear drive). Modulation shaping is performed internally by a 2nd order lowpass filter, which minimises spectral spreading. The RF output is filtered to ensure compliance with the appropriate regulations and fed via a Tx/Rx changeover switch to the antenna pin. The receive section is a single conversion FM superhet with an IF of 10.7MHz. A SAW bandpass filter in the receiver front-end provides image rejection and suppression of other unwanted out-of-band signals. Like the transmitter, the receiver is controlled by its own active low RX select line. A post-detection lowpass filter establishes the signal bandwidth and ensures clean operation of the subsequent adaptive data slicer. The slicer is optimised for balanced data such as bi-phase code. A received signal strength (RSSI) output with 60dB of range is provided. A version of BiM2/3G featuring a fast acting Carrier Detect (CD) output on the same RSSI pin is also available. The CD output will indicate the presence of any RF signals on the carrier frequency. side view (through can) 5 mm side view (with can) top view (without can) RF GND 1 Antenna 2 RF GND 3 4 5 No pin 6 7 8 0V 9 30.48 mm 33 mm 18 0V 17 Vcc 16 RX SELECT 15 TX SELECT 14 TXD 13 AF 12 RXD 11 RSSI/CD 10 0V 23 mm recommended PCB hole size: 1.2 mm module footprint size: 25 x 32 mm pin pitch: 2.54 mm (0.1") pins 4, 5, 6, 7 & 8 are not fitted Fig. 2: Physical dimensions Pin description RF GND pins 1 & 3 RF ground pins, internally connected to the module screen and to pins 9, 10 & 18 (0V). These pins should be connected directly to the RF return path (e.g. coax braid, main PCB ground plane etc). Antenna pin 2 50Ω RF connection to the antenna, DC-isolated. See pages 7 & 8 for details of suitable antennas and feeds. 0V (GND) pins 9, 10 & 18 Supply ground connection and screen. RSSI /CD pin 11 RSSI variant: Received Signal Strength Indicator with 60dB range, operational when Rx is enabled. Output voltage nominally 0.50Vdc (no signal), 1.0Vdc (maximum strength). See page.6 for typical characteristics. Carrier Detect variant: When the receiver is enabled, a low indicates a signal above the detection threshold is being received. The output is high impedance and should only be used to drive a CMOS logic input. Radiometrix Ltd, BIM2/3G Data Sheet page 2 RXD pin 12 Digital output from internal data slicer. The output is a squared version of the signal on pin 13 (AF) and may be used to drive a decoder directly. The data is true data, i.e. as fed to the transmitter. Output is “open-collector” format with internal 10kΩ pullup to Vcc (pin 17). AF pin 13 Buffered & filtered analogue output from FM demodulator. Standing DC bias of 1V approx. Useful for test purposes or for driving external decoders. External load should be >10kΩ // 50kΩ. TX select pin 15 Active-low Transmit select. 47kΩ internal pull-up to Vcc. RX select pin 16 Active-low Receive select. 47kΩ internal pull-up to Vcc. Pin 15 TX Pin 16 RX Function 1 1 Power down ( full RF output 5. ±30kHz FM deviation –15 and –64 versions on;y 6. Min/max at ±50kHz offset 7. Max at ±50kHz offset 8. Average, at max. data rate 9. Dependant on version Power supply requirement The power supply ripple/noise should be below 10mVp-p to avoid problems. If the quality of the supply is in doubt, it is recommended that a 10µF low-ESR tantalum or similar capacitor be added between the module supply pin (Vcc) and ground, together with a 10Ω series feed resistor between the Vcc pin and the supply rail. The BIM2/3G incorporates a low voltage shutoff circuit, which prevents any possibility of erratic operation by disabling the RF output of the transmitter if the supply voltage drops below 2.2V (±5%). This feature is selfresetting, i.e. restoring the supply to greater than 2.2V will immediately restore full RF output from the module. The standard BiM2/3G requires a regulated 5V supply with ripple content