0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
KRX416-000-SO

KRX416-000-SO

  • 厂商:

    RADIOMETRIX

  • 封装:

  • 描述:

    KRX416-000-SO - Code-hopping decoder with 4 outputs - Radiometrix Ltd

  • 数据手册
  • 价格&库存
KRX416-000-SO 数据手册
EW N Radiometrix Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233 Issue: 1, 28 February 2008 KRX416 CodeCode-hopping decoder with 4 outputs Code Key-code Receiver 416 is a single IC solution for decrypting and decoding Radiometrix code-hopping transmitters. The device will retain the identities of up to 16 code-hopping transmitters, even when the power supply is removed. It is specifically designed to be used in RF keyless remote control applications and is available in 18pin SO and DIL packages. Figure 1: KRX416 in 18 pin DIL package Features • • • • • • • • • • • • • • Operating voltage (temperature): 4.5V-5.5V (-40°C to +85°C) Draws 10s Pin 2 goes low then momentarily high again (when Pin 1 returned high) to indicate NV Memory has been cleared. Active high (10ms or for as long as S0-S3 are active) when not in Learn Mode to indicate that the IC has decoded a Function Code (S0S3 state) that was used previously in Learning a Transmitter. Do not connect anything to this pin Normally held high. Taken low this pin will Reset the IC. The NV Memory is unaffected. Supply Ground Function Code output S0 – active high 10ms pulse2 or a 350-500ms pulse and held high for repeat messages (see “Mode” description) Function Code output S1 – operation as above Function Code output S2 – operation as above Function Code output S3 – operation as above Do not connect anything to this pin Active high when the received message indicates that the Transmitter encoder power supply is below 3.8V (approx.) Do not connect anything to this pin 4.5-5.5V supply (decouple with 0.1µF close to IC) Do not connect anything to this pin Data input from receiver, also connect to Vdd via 10k (no input =1) Can be held high or low. When high, outputs S0-S3 are active only for a brief period but when Mode is held low a “latency” is effected. KRX416 page 2 2 LED-L Output1 3 4 5 6 7 8 9 10 11 12, 13 14 15, 16 17 18 NC RST Vss S0 S1 S2 S3 NC LED-V NC Vdd NC RXD MODE Input Supply Output1 Output1 Output1 Output1 Output1 Supply Input Input3 Radiometrix Ltd Notes: 1. 2. 3. Absolute maximum source/sink current from each S0-S3, LED-L, LED-V pins is 25mA. Output pulse length is between 10 and 12ms Can be held high or low. When high, the outputs S0-S3 will be active only for a brief period (see note 2), even if the same message continues to be received over and over again – this is intended as a control pulse for interfacing to additional logic or a microcontroller and is the most basic and secure way to use the decoder. When low, the outputs will be active for 350-500ms (approx.) and this long period allows “refreshing” by repeat messages from the same transmitter. In this way, repeated transmissions with the same code (e.g. a user holding down a function-code button at the transmitter) will cause the respective decoder output also to stay active, until the message ceases to be received within the 350-500ms window. The function-code may change (i.e. be added to) but the outputs will not be cleared until reception of the message has ended. Data from a code-hopped message Transmission format is 1250bps (nominal rate) Manchester encoding. Although the function-code is only 4 bits, total message length is 67 bits. This includes a 28-bit serial number and a 32-bit encrypted hop-code. Note that the serial number and function code data is not encrypted. The correct status of the transmission is used to validate the data. This is achieved through use of the ever changing hopcode (changes for every new message) and by synchronising the KRX416 IC to the transmitter(s) in use. Put another way: the KRX416 “Learns” individual unique transmitters, as required by the user. The hop-code is encrypted using the serial number of the transmitter plus the manufacturer code (64bit), which is kept secret and is not transmitted. The function-code (S0-S3) appears twice in the message and forms a part of the hop-code encryption process. If the KRX416 loses synchronisation with the transmitter (e.g. repeated transmitter activation whilst out of range of the receiver) then the transmitter must be activated twice with valid and sequential hopcodes before KRX416 will allow the control to be processed. The hop-code is only valid if it is within a forward window of +32768 activations. This mechanism prevents “code-grabbers” from breaking the security of the system by recording and re-broadcasting old codes. Additionally, in the KRX416 a window exists allowing up to 14 transmissions to occur whilst the transmitter is out of range before two valid sequential transmissions are required to use the system. In practice a user may not notice the latter, since human reaction to the unsuccessful attempt is simply to “press the button again”. The level of redundancy and encryption in a message mean that, in simple terms, the KRX416 will only output a function-code that has been received from a properly recognised and synchronised transmitter. Start of new message RXD Function S0 =1 150ms: end of message 240ms: function activated Message repeated.... S0 Output Figure 3: Timing diagram – showing action upon receiving a message with S0 = 1 In a typical set-up, the time delay between “button-press” at the transmitter and function activation by the KRX416 IC at the receiver is approx. ¼s. Radiometrix Ltd KRX416 page 3 Application Modes Mode 1 0 Description Short output pulse – suggested for logic and microcontroller interfacing Long output pulse (& held by repeated message) – simple “output follows input”. Example use: handheld remote controller KRX416 can be used with wideband or narrowband radio modules. Ordering Information KRX416-000-SS Key-code Decoder 16 transmitter learn capacity - Shrink Small Outline KRX416-000-SO Key-code Decoder 16 transmitter learn capacity - Small Outline KRX416-000-DIL Key-code Decoder 16 transmitter learn capacity - Plastic Dual In Package Radiometrix Ltd KRX416 page 4 Radiometrix Ltd Hartcran House 231 Kenton Lane Harrow, Middlesex HA3 8RP ENGLAND Tel: +44 (0) 20 8909 9595 Fax: +44 (0) 20 8909 2233 sales@radiometrix.com www.radiometrix.com Copyright notice This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner. Limitation of liability The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications. The Intrastat commodity code for all our modules is: 8542 6000 R&TTE Directive After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular equipment. Further details are available on The Office of Communications (Ofcom) web site: http://www.ofcom.org.uk/radiocomms/ifi/ Information Requests Ofcom Riverside House 2a Southwark Bridge Road London SE1 9HA Tel: +44 (0)845 456 3000 or 020 7981 3040 Fax: +44 (0)20 7783 4033 information.requests@ofcom.org.uk European Radiocommunications Office (ERO) Peblingehus Nansensgade 19 DK 1366 Copenhagen Tel. +45 33896300 Fax +45 33896330 ero@ero.dk www.ero.dk
KRX416-000-SO 价格&库存

很抱歉,暂时无法提供与“KRX416-000-SO”相匹配的价格&库存,您可以联系我们找货

免费人工找货