RQRA-0200-LPH

RQR-VCO Series Electrical Specifications Page 1 of 5 RQRA-0200-LPH 1.0 ELECTRICAL SPECIFICATIONS PARAMETER CONDITION SYMBOL VALUE Min. Frequency Range Vt=0~5.0V fo(Vt) UNIT Typ. Max. 200 MHz Power Supply Voltage Vcc 4.75 Tuning Voltage Vt 0 Supply Current Icc 18 Kvo 0.8 MHz/V Vtcap 330 pF Tuning Sensitivity Over Tuning Range Tuning Port Capacitance 5.0 5.25 V 5.0 V 35 mA Modulation Bandwidth @3dB BW MBW 1000 Pushing Over ±5 % Supply Variation df/dVcc 0.1 0.2 MHz/V Pulling 1.2 @12dBr, all phases df/dZL 0.5 1.0 MHz/p-p 85 °C -45 90 °C -0.4 8.0 V Operating Temperature Ta Storage Temperature Maximum Limits Voltage -40 Tstor For Vcc(abs) Moisture Sensitivity Level MSL JEDEC JSTD-2 HBM Human body model JESD22A114 Termination Finish kHz 1 Glass-reinforced laminate base and nickel-silver cover ESD Sensitivity kV 3 2.0 OUTPUT CHARACTERISTICS SINE-WAVE VALUE PARAMETER SYMBOL Output Power Pw 2nd Harmonic Suppression rd 3 Harmonic Suppression Output Load a(n*fo) OCL CONDITION Output termination 50 Vt=0~5.0V, Vcc=5.0V Min Typ. Max UNIT 7.0 9.0 11.0 dBm -30 -15 -35 -15 dBc 50 Ω R A L T R O N E L E C T R O N I C S  1 0 4 0 0 N .W . 3 3 r d S t r e e t  M i a m i , F l o r i d a 3 3 1 7 2  U . S . A . Telephone: 305-593-6033  Fax: 305-594-3973  e-mail: sales@raltron.com  web: www.raltron.com RQR-VCO Series Electrical Specifications Page 2 of 5 RQRA-0200-LPH 3.0 MECHANICAL DIMENSIONS AND PIN FUNCTIONING H= 0.236 Max. 6.0  Marking: RQRA 0200-LPH 1 Date code R A L T R O N E L E C T R O N I C S  1 0 4 0 0 N .W . 3 3 r d S t r e e t  M i a m i , F l o r i d a 3 3 1 7 2  U . S . A . Telephone: 305-593-6033  Fax: 305-594-3973  e-mail: sales@raltron.com  web: www.raltron.com RQR-VCO Series Electrical Specifications Page 3 of 5 RQRA-0200-LPH 4.0 PHASE NOISE VALUE PARAMETER SYMBOL CONDITION Min Typ Max f=1.0kHz -110 -105 f=10kHz -135 -130 f=100kHz -155 -150 f=1000kHz -160 -155 f=10MHz -160 -155 UNIT  f) SSB Phase noise dBc/Hz  Typical Phase Noise Graph: R A L T R O N E L E C T R O N I C S  1 0 4 0 0 N .W . 3 3 r d S t r e e t  M i a m i , F l o r i d a 3 3 1 7 2  U . S . A . Telephone: 305-593-6033  Fax: 305-594-3973  e-mail: sales@raltron.com  web: www.raltron.com RQR-VCO Series Electrical Specifications Page 4 of 5 RQRA-0200-LPH 5.0 COMMON SPECIFICATIONS 5.1 Load impedance is 50 Ohms. 5.2 Pulling is measured with 12dB return loss, all phases. 5.3 Package outline tolerances are typ. ±0.30mm / ±0.012 inch if not stated differently on the drawing. 5.4 It is recommended to provide two bypass-capacitors (ceramic), from Vcc to Gnd, 1nF || 100pF. 5.5 Solder temperature (peak) is 260°C for 10-20 sec. 6.0 ENVIROMENTAL SPECIFICATIONS COMMON SPECIFICATIONS 6.1. Storage Temperature Range: -45 to +90°C ambient 6.2. Operating Temperature Range: -40 to +85°C ambient 6.3. Operating Humidity: 15 to 100% relative humidity, non-condensing 6.4. Storage Humidity: 0 to 100% relative humidity, non-condensing 6.5. Operating Altitude: Up to 10,000 feet above sea level 6.6. Storage and Transport Altitude: Up to 50,000 feet above sea level 7.0 MECHANICAL- ELECTRICAL-ASSEMBLY PROCESS REQUIREMENTS 7.1. Mechanical and electrical performance specified in tables 1.0; 2.0; 3.0 and 4.0 should be met and exceeded the call out specification. 7.2. Module assembly process should be cleaned via an aqueous based system for normal SMT assembly processes. 7.3. The module internally and externally should be free off solder flux and residue from assembly processes. 7.4. High temperature solder such as SN95 or SN96 or equivalent should be used for internal construction of part. 7.5. When measuring the electrical performance, part must be completely dry, as any entrapped moisture will cause erroneous results. R A L T R O N E L E C T R O N I C S  1 0 4 0 0 N .W . 3 3 r d S t r e e t  M i a m i , F l o r i d a 3 3 1 7 2  U . S . A . Telephone: 305-593-6033  Fax: 305-594-3973  e-mail: sales@raltron.com  web: www.raltron.com RQR-VCO Series Electrical Specifications Page 5 of 5 RQRA-0200-LPH 8.0 REFLOW PROFILE tP TP Critical Zone TL to TP Ramp-up TL tL TSMAX Temp. [°C] TSMIN Ramp-down tS Preheat t[25°C] to Peak Time [sec] Recommended Solder Reflow Profile TSMIN TSMAX tS TL TP RUP RDOWN tP t[25°C] to Peak tL Temperature Min Preheat Temperature Max Preheat Time (TSMIN to TSMAX) Temperature Peak Temperature Ramp-up rate Ramp-down rate Time within 5°C of Peak Temperature Time t[25°C] to Peak Temperature Time 150°C 175°C 60-180 sec. 217°C 260°C 3°C/sec max. 6°C/sec max. 10-20 sec max. 480 sec. 60-150 sec. 9.0 APPROVALS Eng. approval, date: IM 11/20/2017 Created by, date: 11/20/2017 MH Revision: A R A L T R O N E L E C T R O N I C S  1 0 4 0 0 N .W . 3 3 r d S t r e e t  M i a m i , F l o r i d a 3 3 1 7 2  U . S . A . Telephone: 305-593-6033  Fax: 305-594-3973  e-mail: sales@raltron.com  web: www.raltron.com