RQRA-0463-0514

Voltage Controlled Oscillator-VCO RQRA-0463-0514 Page 1 of 2 RQRA-0463-0514 1. Product Control Part Number RQRA-0463-0514 Rev Initiated Updated A 10/17/2013 L_typ see 6.4 3. Electrical Specification Parameter Conditions Lower Frequency see 6.2 Tuning Voltage: Upper Frequency see 6.2 Tuning Voltage: Supply Voltage Symbol Min 10 V fo(Vt) 514 Vt 0.5 Vcc 4.75 Tolerance: ± 0.25V Output Power Pout Tuning Sensitivity maximum to minimum ratio df/dVt Tuning Sensitivity Over 463-514MHz df/dVt Pulling see 6.3 Harmonic Suppression Typ -H2 -H3 +2.0 Unit 4.0(.157) mm (inch) Max Unit 463 MHz MHz 5.0 Icc 50 ohms load Over Supply Variation 5V±5% VSWR load=2:1 at all phase RFQ H_max 12.7(.500) fo(Vt) Supply Current Pushing W_typ 12.7 (.500) 0.5 V Tuning Voltage Spec-ID MH 2. Mechanical Specification Parameter Conditions Length x Width x Height Responsible + 5.5 10 V 5.25 V 30 mA +8.0 dBm 1.5 - 7.0 MHz/V df/dVcc 200 KHz df/dZL 200 KHz a(n*fo) -30 -30 dBc Non harmonic spurious - f  4.0 kHz - f > 4 kHz -60 -100 dBc Freq.Offset value: -90 -114 -125 -128 1.0kHz 12.5kHz SSB Phase Noise at offset frequency over 0 to 55°C 25kHz 50kHz L(df) -140 -143 -147 -150 -165 100kHz 200kHz 500kHz 1MHz >5MHz 4. Extended Specification -89 -113 -120 -127 dBc/Hz -138 -140 -145 -145 -160 5. Marking -------- RQRA 0463-0514 D/C Top view rd RALTRON ELECTRONICS  10400 N.W . 33 St  Miam i, Florida 33172  U.S.A. phone: +001(305) 593-6033  fax: +001(305) 594-3973  e-mail: sales@raltron.com  internet: http://www.raltron.com Voltage Controlled Oscillator-VCO RQRA-0463-0514 Page 2 of 2 RQRA-0463-0514 Date/Product Code 6. Common Specification 6.1 Load impedance is 50 Ohms if not stated differently in (4.) "Extended Specification". 6.2 The frequency range is defined between the (max) lower frequency and (min) upper frequency. 6.3 Pulling is measured with 12dB return loss, all phases. 6.4 Package outline tolerances are typ. ±0.38mm/±.015inch if not stated differently on the drawing. 6.5 Product consists of glass-reinforced laminate base and nickel-silver cover. 6.6 It is recommended to provide two bypass-capacitors (ceramic), from Vcc to Gnd, 1nF || 100pF. 6.7 Solder temperature (peak) is 230°C for 10s or 260°C for 5s. 6.8 Operating temperature range is -30°C~+85°C if not stated differently in (4.) "Extended Spec". 7. Outline Drawing rd RALTRON ELECTRONICS  10400 N.W . 33 St  Miam i, Florida 33172  U.S.A. phone: +001(305) 593-6033  fax: +001(305) 594-3973  e-mail: sales@raltron.com  internet: http://www.raltron.com