RQRA-0600-0660

RQRA VCO SERIES Page 1 of 4 RQRA-0600-0660 ELECTRICAL SPECIFICATIONS PARAMETER CONDITION SYMBOL VALUE Min. Frequency Range Vt=0.5 V Vt=5.0 V fo(Vt) 4.75 Tuning Voltage Vt 0.5 Tuning Sensitivity Max. 600 Vcc Vcc=5.0V ±5% Vt=0.5~5V Vcc=5.0V ±5% T=25°C Typ. MHz 660 Power Supply Voltage Supply Current UNIT Icc 5.0 15 df/dVt 15 5.25 V 4.5 V 20 mA 30 MHz/V Modulation Bandwidth @-3 dB 60 MHz Tuning Port Capacitance Vt=0.5~5V 68 pF Pushing Vcc=4.75 – 5.25V df/dVcc 1 2 MHz/V Return Loss: 12dB df/dZL 1 2 MHz-pk-pk Pulling 1.2 Operating Temperature Ta -35 85 °C Storage Temperature Tstor -55 100 °C -0.4 8.0 V Maximum Limits Voltage Vcc(abs) MSL JEDEC JSTD-2 HBM Human body model JESD22A114 Moisture Sensitivity Level Termination; Finish 1 Glass-reinforced laminate base and nickel-silver cover ESD Sensitivity kV 3 OUTPUT CHARACTERISTICS SINE-WAVE VALUE PARAMETER SYMBOL Output Power Pw 2nd Harmonic Suppression CONDITION 2 h 3 Output termination 50 Vcc=5.0V ±5% Min Typ. Max UNIT -2 -1 4 dBm -13 -8 dBc -20 -10 dBc 3nd Harmonic Suppression h Spurious (Non-Harmonic) Sp -90 dBc Output Load(Imped) OCL 50 Ω R A L T R O N E L E C T R O N I C S ▪ 1 0 4 0 0 N .W . 3 3 r d S t r e e t ▪ M i a m i , F l o r i d a 3 3 1 7 2 ▪ U . S . A . Telephone: 305-593-6033 ▪ Fax: 305-594-3973 ▪ e-mail: sales@raltron.com ▪ web: www.raltron.com RQRA VCO SERIES Page 2 of 4 RQRA-0600-0660 MECHANICAL DIMENSIONS AND PIN FUNCTIONING H= 0.156 3.96 ◼ H Tolerance: ±0.020in ±0.51mm PIN SYMBOL FUNCTION 2 Vt Control Voltage 10 Rfout RF Output 14 Vcc Power Supply 6,Others, Cover GND Ground Marking: RQRA 0600-0660 1 Date code R A L T R O N E L E C T R O N I C S ▪ 1 0 4 0 0 N .W . 3 3 r d S t r e e t ▪ M i a m i , F l o r i d a 3 3 1 7 2 ▪ U . S . A . Telephone: 305-593-6033 ▪ Fax: 305-594-3973 ▪ e-mail: sales@raltron.com ▪ web: www.raltron.com RQRA VCO SERIES Page 3 of 4 RQRA-0600-0660 PHASE NOISE VALUE PARAMETER SSB Phase noise SYMBOL CONDITION Min Typ f=1.0kHz -90 f=10kHz -112 f=100kHz -133 f=1000kHz -151 Max (f) UNIT dBc COMMON SPECIFICATIONS 1.1 -Load impedance is 50 Ohms. 1.2 -Pulling is measured with 12dB return loss, all phases. 1.3- Package outline tolerances are typ. ±0.30mm / ±0.012 inch if not stated differently on the drawing. 1.4 -It is recommended to provide two bypass-capacitors (ceramic), from Vcc to Gnd, 1nF || 100pF. 1.5- Solder temperature (peak) is 260°C for 10-20s. Environmental Compliance PARAMETER CONDITIONS Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Resistance to Solvents MIL-STD-883, Method 2016 R A L T R O N E L E C T R O N I C S ▪ 1 0 4 0 0 N .W . 3 3 r d S t r e e t ▪ M i a m i , F l o r i d a 3 3 1 7 2 ▪ U . S . A . Telephone: 305-593-6033 ▪ Fax: 305-594-3973 ▪ e-mail: sales@raltron.com ▪ web: www.raltron.com RQRA VCO SERIES Page 4 of 4 RQRA-0600-0660 REFLOW PROFILE tP TP Critical Zone TL to TP Ramp-up TL tL TSMAX Temp. [°C] TSMIN Ramp-down tS Preheat t[25°C] to Peak Time [sec] Recommended Solder Reflow Profile TSMIN TSMAX tS TL TP RUP RDOWN tP t[25°C] to Peak tL Temperature Min Preheat Temperature Max Preheat Time (TSMIN to TSMAX) Temperature Peak Temperature Ramp-up rate Ramp-down rate Time within 5°C of Peak Temperature Time t[25°C] to Peak Temperature Time 150°C 175°C 60-180 sec. 217°C 260°C 3°C/sec max. 6°C/sec max. 10-20 sec max. 480 sec. 60-150 sec. APPROVALS Eng. approval, date: IM 9/7/2018 Created by, date: 9/7/2018 MP Revision: A R A L T R O N E L E C T R O N I C S ▪ 1 0 4 0 0 N .W . 3 3 r d S t r e e t ▪ M i a m i , F l o r i d a 3 3 1 7 2 ▪ U . S . A . Telephone: 305-593-6033 ▪ Fax: 305-594-3973 ▪ e-mail: sales@raltron.com ▪ web: www.raltron.com