CL082C-1000-G

THICK FILM SIP NETWORKS . RCD CL101S . RCD CL101 RESISTORS CAPACITORS COILS DELAY LINES CL SERIES - Low Profile C SERIES - High Power Low cost, widest selection in the industry! Term.W is RoHS 4-pin through 14-pin standard (2 through compliant 20-pin sizes available on special order) RoHS & 260°C compatible CL Series low-profile available from stock (configuration1 & 2 in 6, 8, and 10-pin) Wide resis. range: 10Ω to 3MΩ std., 1Ω to 1000M avail. Bulk packaging is standard, tape or magazine tube avail. R/2R Ladder Networks (Config. 7) offer 1/2LSB accuracy from 4 to 10 bits ←New high density Sips, an RCD exclusive! . RCD C101 OPTION V OPTION S OPTION P OPTION N OPTION F OPTION C - +200°C temperature Range Super high density (.070” pin spacing) Pulse tolerant design Narrowline design (.070” thick) Flameproof coating Copper alloy terminals STANDARD CONFIGURATIONS Configuration No. 1 > > > > > > > > > > > > > > > Also available in custom circuits with multiple values/capacitors/ diodes, increased power & voltage, tolerance & TC matching, longer pins, special marking, military burn-in, resis. values 1Ω to 1000M, etc. Configuration No. 2 > > > > > > > > > > > > DIMENSIONS .095 [2.4] Max. Opt. N= .070±.008 [1.8±.2] ...... > > > > > > → ← ←Length=0.1” X No. of pins max→ Pin #1 1 1 . C=.315 [8] Max. CL=.195 [5] Max. ↑ ↓ Configuration No. 3 Configuration No. 4 .. > > > > R2> R2> .. > > R1> > R1> 1. .> . > > R2> . > R1> .> . > > R2> . > R1> .> . > > R2> . > R1> .> . > > R2> . > R1> .> . 1 > > > . > > > . > > > . > > > . > > > . > > > .011 [.28] →← .020 [.5] Dimensions: Inch [mm] →← → ← .100 ± .01 [2.54 ± .25] ↑ .102 [2.6] Min. ↓ Opt.S=.070± .01 [1.78 ±.25] Configuration No. 5 > > > > > > > > > > > > Configuration No. 6 vvv vvv vvv vvv vvv Config. No. 7 R/2R R R R 1 1 > > > > > > > > > > 1 > 2R > 2R > 2R > 2R > 2R vvv vvv vvv SINGLE RESISTOR PACKAGE POWER RATING* POWER RATING* RCD Type Config. Config. Config. 4-Pin 6-Pin 7-Pin 8-Pin 9-Pin 10-Pin 12-Pin 1,3,4,5,6 2 3, 7 C .3W .5W .17W 1W 1.5W 1.75W 2W 2.25W 2.5W 3W CL .2W .3W .125W** .5W 1W 1.25W 1.5W 1.75W 2W 2.5W * Reduce wattage ratings by 1/3 for Opt.S **Config. 7 n/a in CL Series GND LSB MSB OUT STANDARD VALUES- Config. 1, 2, 4, 5, 6: % OF RATED POWER 100 80 60 40 20 0 25 50 75 100 125 AMBIENT TEMPERATURE (°C) 150 % OF RATED POWER 10Ω to 3M in E-24 values (preferred values in bold type)10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91 81/130 120/195 121/195 160/260 162/260 180/390 220/270 220/330 330/390 330/470 330/680 3K/6.2K DERATING 120 (Series C and CL) DERATING 120 100 80 60 40 20 0 (Option V) STANDARD VALUES - Config. 3, Dual Terminator, R1/R2 : R/2R LADDER NETWORKS (Config.7): 4Bit/6-pin, 5Bit/7-pin, 6Bit/8-pin, 7Bit/9-pin, 8Bit/10-pin, 9Bit/11-pin, and 10Bit/12-pin. Available in Series C (low profile Series CL n/a). Linearity accuracy is 1/2LSB. Standard values are 5KΩ, 10KΩ, 25KΩ, 50KΩ, & 100KΩ ±2%. 40 80 120 160 200 240 AMBIENT TEMPERATURE (°C) TYPICAL PERFORMANCE SPECIFICATIONS Tolerance Temperature Coefficient TCR Tracking Operating Temperature Max. Working Voltage Short Time Overload Resis. to Solder Heat Moisture Resistance Terminal Strength Thermal Shock Load Life (1000 hours) Temperature Cycling Shock and Vibration Lead Solderability Marking Terminals 2% Standard (1%, 5% avail.) ±100ppm typ (±250ppm 2.2M) 50PPM typical -55°C to +125°C (+200°C Opt.V) 200V Series C, 100V Series CL & Opt.S ±0.5% (2.5x rated V, 5S, nte 2xW) ±0.25% (350°C, 5S) ±1% ±0.25% ±0.5% ±1.0% ±0.5% ±0.25% Meets MIL-R-83401 Pin #1 ID, resis value, & tol as minimum Solder plated steel typ., copper alloy* avail. P/N DESIGNATION: Type: CL=low profile (std), C=high power Number of Pins CL 0 8 2 - 102 - G B W Configuration Number Options: V,S,P,N,F,C (leave blank if std) Resis.Code 1%: 3 signif. figures & multiplier, (e.g. 10R0=10Ω, 1000=100Ω, 1001=1K, 1004=1M) Resis.Code 2%-5%: 2 signif. figures & multiplier, (e.g. 100=10Ω, 101=100Ω, 102=1K, 103=10K, 104=100K, 105=1M) When comprised of 2 res.values (config.3&7) separate with /, e.g. 181/391=180Ω/390Ω Tolerance Code: G=2% (standard), F=1%, J=5% Packaging: B=bulk, A3=3 pin taping ammo pack, M=magazine tube Opt. TC: 50=50ppm,101=100ppm (leave blank if standard) Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is acceptable) * RCD recommends use of copper alloy terminals (opt. C) in aqueous cleaning systems RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603-669-0054 Fax: 603-669-5455 Email:sales@rcdcomponents.com FA032B Sale of this product is in accordance with GF-061. Specifications subject to change without notice. 38