20001380

M C O N V ER T Input Output Voltage Voltage Range Factory Set [VAC] [VDC] Output Voltage Range [VDC] 80-264 24 24-28 50 95 RACM1200-36SAV/ENC 80-264 36 30-36 40 95 RACM1200-48SAV/ENC 80-264 48 48-56 25 95 Notes: Note1: Efficiency is tested at nominal input and 40-60% load at +25°C ambient temperature Accessible Part RAC-MB1 Description Datasheet Link mounting bracket RAC-MB1.pdf Model Numbering RACM1200-__ S AV/ENC/PMB Peak Output Power Nom. Output Voltage Single TS C D IA N T PRO U CO NVE R T REACH compliant M P ERP compliant LOT6 U LIA D N T PRO Max. Output Efficiency Current typ. (1) [A] [%] RACM1200-24SAV/ENC Part Number PL M S M O CO Part Number CO Selection Guide 10 from 10 C R S RoHS 2 + compliant E O R C E RE 1200 Watt 9” x 3.8” Enclosed Single Output TS Description The RACM1200-V series is setting a new benchmark for compactness in the class of AC power supplies for reliable fan-less operation supporting long term system availability. A special baseplate cooled design supports heat transfer to allow up to 1000W continuous output power. Up to 1200 Watt output power is available for up to 10 seconds and in boost mode operation or for extended time with sufficient system airflow through the unit. A wide output voltage adjustment range and a combination of constant current limitation and hiccup mode settings makes the product multipurpose. The various analogue control and monitoring functions are accessible via connector. Optional firmware settings available on project base. The RACM1200-V Series can be limited to inherently fail-safe settings on request, using smart, controlled, fault-limiting functions. Only the /PMB Variant supports default settings ex factory to be adjusted, and warning signals to be adopted. An adjustable 12V system FAN output and a 1.5kVAC isolated auxiliary stand by output of 5VSB/1A are available to power the application’s housekeeping functions. Peak efficiency reaches up to 95% and in standby mode, the unit is compliant to ecodesign requirements. The product holds worldwide safety files to medical, industrial and ITE standards along with electromagnetic compatibility compliance with class A immunity and class B emissions. Spring stainless steel mounting brackets are available separately for a perfect fixation when mounting over the top of the base plate is preferred. All these features make the product one of the easiest to integrate modular power solutions in the industry. RACM1200-V C Regulated Converter AC/DC Converter RE • Up to 1000 Watt fan-less power / 1200W boost • Designed and manufactured in europe • Efficiency exceeding 90% from 15% load • Wide Operating temperature range -40…+80°C • Certified to Industrial, and medical standards • Analogue control & monitor function • Custom Variants Features PMBus function (2) E224736 2MOPP 250VAC IEC/EN62368-1 certified UL62368-1 certified CAN/CSA-C22.2 No. 62368-1 certified IEC/EN60601-1 certified ANSI/AAMI ES60601-1 certified UL8750 (48V only) certified IEC/EN61347-1 (pending) IEC/EN61347-2-13 (pending) IEC/EN61558-1/2 compliant (9) IEC61010-1/-2-201 compliant (10) IEC/EN60601-1-2 compliant EN55032/35 compliant EN55024 compliant CB Report Enclosed Case Style VSB Auxiliary Output Voltage (5VDC) Notes: Note2: with suffix “/PMB” PMBus option is built-in (available with 24V and 48V Versions) For master commands please refer to link: PMBus_mastercommands.pdf www.recom-power.com REV.: 4/2023 PA-1 RACM1200-SAV Series AC/DC Converter Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Nominal Input Voltage 60/50Hz 100VAC 240VAC Operating Range 47-63Hz 80VAC 264VAC Input Current according to CB report Inrush Current cold start at +25°C, 230VAC Typ. Max. 11.5A No load Power Consumption MAIN output REMOTE ON Standby Power MAIN output REMOTE OFF 14A 25A 2W 1W Minimum Load 0% refer to ”Power Factor” Power Factor 5VSB Aux. refer to “SIGNALS” Start-up Time Hold-up Time 500ms FAN 750ms 1.5s MAIN, 800W, 85-264VAC (-25°C to +70°C) 750ms 1.5s 800W 20ms 20MHz BW, valid for MAIN, 5VSB, FAN Output Ripple and Noise (3) 1% of nom. Vout Notes: Note3: Measurements are made with a 0.1μF MLCC & 10μF E-cap in parallel across output. (low ESR) Efficiency vs. Load Power Factor 1.1 90 1 80 0.9 Power Factor [ ] Efficiency [%] 100 70 60 50 40 0.7 0.6 0.5 0.2 20 0.1 10 0 0 0 115VAC 240VAC 0.4 0.3 115VAC 240VAC 30 0.8 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Output Load [W] 100 200 300 400 500 600 700 800 900 1000 1100 1200 Output Load [W] Power Dissipation 100 Power Dissipation [W] 90 80 70 60 50 40 30 20 115VAC 240VAC 10 0 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Output Load [W] www.recom-power.com REV.: 4/2023 PA-2 RACM1200-SAV Series AC/DC Converter Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) REGULATIONS Parameter Condition Set Point Accuracy Total Regulation Value MAIN ±1.0% max. 5VSB / FAN ±5.0% max. line, load and temperature drift MAIN & FAN ±2.0% max. 5VSB Aux. ±5.0% max. ADDITIONAL FEATURES Parameter Condition 5VSB Stand By Output Voltage Min. 1A 24Vout type (100mV steps) Remote ON/OFF Max. 5VDC always on 5VSB Stand By Output Current Output Voltage Adjustability Typ. 24VDC 28VDC tactile button push up/down 36Vout type (150mV steps) 30VDC 36VDC 48Vout type (200mV steps) 48VDC 56VDC maximum allowed voltage referenced to SIGNAL RTN FAN Output Voltage adjustment via FAN ADJ Pin #6 @ TTL levels 5VDC OFF CTRL= 2.5VDC CTRL= 2.2VDC...0VDC or open 5VDC FAN Output Current ON/OFF with MAIN channel 12VDC 1A “Remote Sense” differential mode, cable loss compensation 500mV Parallel Operation please get in touch with your RECOM contact on request Green continuously PSU-Good: PSU in standard operation mode Blue intermittent (30% on) STBY: Standby mode; MAIN Output OFF via REMOTE signal Green intermittent (50% on) DC-LOW: Signal: {75%