RAC04-12SC/277-E

!NOT RECOMMENDED FOR NEW DESIGNS! • 50mW max. no load power consumption Features • High efficiency up to 79% Regulated Converter Description RAC RAC04-C/277 4 Watt Single and Dual Output YEA R 3 arrant w The RAC04-xxS_DC/277 series are fully certified single and dual regulated AC/DC converters in an encapsulated PCB-mount package style with 3.75kVAC isolation and very low stand-by power consumption. The modules are suitable for worldwide use due to their wide input voltage range from 80VAC to 305VAC. Possible uses include home automation, standby applications and industrial controls. AC/DC Converter y • Isolated Output 3.75kVAC / 1 minute • SCP, OVP protection • Wide operating temperature range -40°C to +80°C (only with suffix „-E“) • Universal input 80-305VAC T CONVER T REACH compliant M ERP compliant TS TS C M S PL U D IA N T PRO CO CO 10 from 10 M O R S RoHS 2 + compliant C C CONVER RE M E O R C E RE Selection Guide Part Input Output Output Efficiency Max. Capacitive Number Voltage Range Voltage Current typ. Load (1,2) [(VAC] [VDC] [mA] [%] [µF) RAC04-3.3SC/277(3) 80-305 3.3 1200 72 10000 RAC04-05SC/277 (3) 80-305 5 800 75 7200 RAC04-12SC/277 (3) 80-305 12 333 78 1000 RAC04-15SC/277 (3) 80-305 15 267 79 820 RAC04-24SC/277 (3) 80-305 24 167 79 220 RAC04-0512DC/277 (3) 80-305 5/12 720/33 75 4700/100 RAC04-05DC/277 (3) 80-305 ±5 ±400 76 ±3300 RAC04-12DC/277 (3) 80-305 ±12 ±166 78 ±680 PL U D IA N T PRO E224736 Notes: Note1: Measured @ 230VAC/50Hz/Ta 25°C with constant resistant mode at full load Note2: If used @115VAC/60Hz with full load, max. capacitive load is less, please contact RECOM Tech Support for detailed information PREFERRED ALTERNATIVES Please consider these alternatives: Model Numbering RAC04-K/277 Series RAC04-__ _C/277 -_ Output Voltage Temperature (3) Single or Dual Ordering Examples: e.g. RAC04-3.3SC/277-E, Single Output, with -40° to +80°C operating temperature range e.g. RAC04-05DC/277, Dual Output with standard operating temperature range RAC10-K/277 Series IEC/EN60950-1 certified IEC/EN62368-1 certified UL60950-1 certified CSA/CAN 22.2 60950-1-07 certified CB Report EN55032 compliance EN55024 compliance Notes: Note3: with suffix “-E” for -40°C to +80°C operating temperature range without suffix standard operating temperature range (-25°C to +80°C) www.recom-power.com REV.: 7/2020 PA-1 ! NOT RECOMMENDED FOR NEW DESIGNS ! RAC04-C/277 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Input Voltage Range (4) Min. Typ. Max. 80VAC 113VDC 277VAC 390VDC 305VAC 430VDC 115VAC 230VAC Input Current Inrush Current 115VAC 230VAC cold start at +25°C No load Power Consumption 98mA 64mA 15A 30A 80-305VAC, 50/60Hz Input Frequency Range 50mW AC input 47Hz 440Hz RAC04-0512DC/277(-E) all others Minimum Load Hold-up time 115VAC Internal Operating Frequency full load Output Ripple and Noise ±5% / ±0% 0% 15ms 67kHz 200mVp-p (5) Notes: Note4: Note5: Refer to line derating graph on page PA-5 Ripple and Noise is measured at 20MHz bandwidth and with a 47µF low-ESR electrolytic capacitor in parallel with a 0.1µF ceramic capacitor across output RAC04-3.3SC/277 (-E) RAC04-05SC/277 (-E) 100 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] Efficiency vs. Load 60 50 40 30 115VAC 230VAC 277VAC 10 40 0 10 20 30 40 50 60 70 80 90 10 0 100 0 10 20 30 40 50 60 70 Output Load [%] Output Load [%] RAC04-12SC/277 (-E) RAC04-15SC/277 (-E) 100 100 90 90 80 80 70 70 60 50 40 30 80 90 100 60 50 40 30 115VAC 230VAC 277VAC 20 10 0 115VAC 230VAC 277VAC 20 Efficiency [%] Efficiency [%] 50 30 20 0 60 0 10 20 30 40 50 60 Output Load [%] www.recom-power.com 70 80 90 115VAC 230VAC 277VAC 20 10 100 continued on next page REV.: 7/2020 0 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] PA-2 ! NOT RECOMMENDED FOR NEW DESIGNS ! RAC04-C/277 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) RAC04-05DC/277 (-E) 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] RAC04-24SC/277 (-E) 100 60 50 40 60 50 40 30 30 115VAC 230VAC 277VAC 20 10 0 0 10 20 30 40 50 60 70 80 90 115VAC 230VAC 277VAC 20 10 0 100 0 10 20 30 Output Load [%] 50 60 70 80 90 100 RAC04-15DC/277 (-E) 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] RAC04-12DC/277 (-E) 100 60 50 40 30 60 50 40 30 115VAC 230VAC 277VAC 20 10 0 40 Output Load [%] 0 10 20 30 40 50 60 70 80 90 115VAC 230VAC 277VAC 20 10 0 100 0 10 Output Load [%] 20 30 40 50 60 70 80 90 100 Output Load [%] REGULATIONS Parameter Output Accuracy Line Regulation Load Regulation (5V minimum load 5% @12V full load)v Condition single and dual 5V/12V dual assymetrical 90-264VAC 10% to 100% load single and dual 5V/12V dual assymetrical 3.3V, 5V output all others 5V/12V dual assymetrical Value ±2.0% typ. ±2.0% / ±10.0% typ. ±0.2% typ. ±0.2% / ±1.0% typ. 1.0% typ. 0.5% typ. 1.0% / 5.0% typ. PROTECTIONS Parameter Type Value Short Circuit Protection (SCP) automatic recovery Over Voltage Category Isolation Voltage Isolation Resistance OVC II I/P to O/P tested for 1 minute Insulation Grade Leakage Current 3.75kVAC 100MΩ min. reinforced 277VAC / 50Hz 0.25mA max. continued on next page www.recom-power.com REV.: 7/2020 PA-3 ! NOT RECOMMENDED FOR NEW DESIGNS ! RAC04-C/277 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) Notes: Note6: Refer to local safety regulations if input over-current protection is also required Note7: To measure the output ripple and noise short runs by 0.1µF/50V & 47µF/50V @20MHz, nominal input and full load Note8: An external MOV is required for 230VAC operation. (MOV model: shall comply with IEC 61051-2) e.g. Epcos S14 Series Protection Circuit VACin (L) FUSE +Vout 0.1µF/50V MOV 47µF/50V VACin (N) -Vout ENVIRONMENTAL Parameter Condition Value 230VAC Operating Temperature Range @ natural convection 0.1m/s with suffix “-E” full load -25°C to +65°C refer to derating graph -25°C to +80°C full load -40°C to +65°C refer to derating graph -40°C to +80°C +90°C Maximum Case Temperature Thermal Impedance 10°C/W Operating Altitude 2000m Operating Humidity non-condensing 95%, RH max. Pollution Degree PD2 Vibration MIL-STD-202G MTBF according to MIL-HDBK-217F, G.B 500 x 103 hours +25°C Derating Graph (@ Chamber and natural convection 0.1m/s) RAC04-xxS(D)C/277-E 100 100 90 90 80 80 70 70 Output Load [%] Output Load [%] RAC04-xxS(D)C/277 60 50 40 60 50 40 30 30 20 20 10 10 0 -25 -20 0 20 40 60 65 0 -40 80 90 Ambient Temperature [°C] -20 0 20 40 60 65 80 90 Ambient Temperature [°C] continued on next page www.recom-power.com REV.: 7/2020 PA-4 ! NOT RECOMMENDED FOR NEW DESIGNS ! RAC04-C/277 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) Line Derating 100 90 Output Load [%] 80 70 60 50 40 30 20 10 0 80 305 Input Voltage [VAC] SAFETY AND CERTIFICATIONS Certificate Type Report / File Number Standard Information Technology Equipment, General Requirements for Safety (CB Scheme) 1310055-1-CB-M1 IEC60950-1:2005, 2nd Edition + A1:2009 Information Technology Equipment, General Requirements for Safety (LVD) SPCLVD1605077-04 EN60950-1:2006 + A2:2013 IEC60950-1:2005 2nd Edition + A2:2013 Information Technology Equipment, General Requirements for Safety E224736-A18 Audio/video, information and communication technology equipment - Safety requirements AL106051 EAC RU-AT.03.67361 RoHS2+ UL No. 60950-1, 2nd Edition, 2011 CAN/CSA C22.2 No. 60950-1-07, 2nd Edition, 2011 EN62368-1:2014 IEC62368-1:2014 2nd Edition TP TC 004/020, 2011 RoHs-2011/65/EU + AM-2015/863 EMC Compliance Report / File Number Electromagnetic compatibility of multimedia equipment - Emission requirements EN55032, Class B T160225D10-E Information technology equipment - Immunity characteristics - Limits and methods of measurement Air: ±2, 4, 8kV Contact: ±4kV ESD Electrostatic discharge immunity test Radiated, radio-frequency, electromagnetic field immunity test 3V/m Fast Transient and Burst Immunity AC Power Port: ±1kV Surge Immunity Standard / Criterion EN55024:2010 IEC61000-4-2:2008, Criteria A IEC61000-4-3:2010, Criteria A IEC61000-4-4:2004 + A1:2010, Criteria A AC Power Port: L-N ±1kV IEC61000-4-5:2005, Criteria A AC Power Port: 3V IEC61000-4-6:2008, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields Power Magnetic Field Immunity 50Hz, 1A/m IEC61000-4-8:2009, Criteria A Voltage Dips and Interruptions Voltage Dips: >95% Voltage Dips: 30% Interruptions: >95% IEC61000-4-11:2004, Criteria A IEC61000-4-11:2004, Criteria A IEC61000-4-11:2004, Criteria B DIMENSION and PHYSICAL CHARACTERISTICS Parameter Type Value Material case potting PCB black plastic (UL94 V-0) silicone (UL94 V-0) FR4 (UL94 V-0) Dimension (LxWxH) 36.7 x 27.2 x 17.1mm Weight 41g typ. continued on next page www.recom-power.com REV.: 7/2020 PA-5 ! NOT RECOMMENDED FOR NEW DESIGNS ! RAC04-C/277 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) Dimension Drawing (mm) 36.7 Pinning information Pin # 1 2 3 4 5 6 7 27.2 embossed logo 36.0 17.1 26.5 Dual Dual (assymetric) No Pin No Pin +Vout +5Vout Com Com -Vout +12Vout VAC in (L) VAC in (L) VAC in (N) VAC in (N) NC* NC* *Pin 7 is NC but need 4mm minimum clearence to ground for safety NC= no connection Tolerance: xx.x= ±0.5mm  xx.xx= ±0.25mm 21.0 4.0 Ø0.6±0.05 Single No Pin +Vout -Vout NC VAC in (L) VAC in (N) NC* Redommended footprint details 21.5 7 7.5 Bottom View 6 Ø0.9±0.1 restricted area for PCB layout 2.54 2 3 4 1 5 21.0 2.54 3.1 3.8 Top View restricted area for PCB layout 1 2 3.75 7 3 4 6 5 3.75 PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube 520.0 x 32.0 x 27.0mm Packaging Quantity 12pcs Storage Temperature Range -40°C to +100°C The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 7/2020 PA-6