RBM-0505D/P

Features Unregulated Converters • Micro size SIP 6 package • Industry standard pinout • Power sharing on dual output version • 3kVDC/1s basic isolation • Optional continuous short circuit protection • Efficiency up to 84% Description The RBM Micro Size DC/DC-Converter complements Recom’s industrial range of converters. This range is widely used for PCB distributed power systems and combines small package size, high efficiency, 3kVDC isolation and low output ripple. The extended operating temperature range covering –40°C to +85°C is a standard feature. The full rated power can be taken from a single pin of this dual output converter, provided this does not exceed 1 Watt. DC/DC Converter RBM 1 Watt SIP6 Micro Size, Single and Dual Output Selection Guide Part Number nom. Input Output Output Efficiency max. Capacitive Voltage Voltage Current typ. (1) Load (2) [VDC] [VDC] [mA] [%] [µF] RBM-xx05S (3) 5, 12 5 200 70-78 1000 RBM-xx12S 5, 12 12 84 78-80 470 RBM-xx15S (3) 5, 12 15 66 80-84 470 (3) RBM-xx05D 5, 12 ±5 ±100 74-78 ±470 RBM-xx12D (3) 5, 12 ±12 ±41 80-82 ±220 RBM-xx15D 5, 12 ±15 ±33 80-84 ±220 (3) (3) Notes: Note1: Efficiency is tested at nominal input and full load at +25°C ambient Note2: Max Cap Load is tested at nominal input and full resistive load and is defined as the capacitive load that will allow start up in under 1s without damage to the converter Model Numbering RBM- __ nom. Input Voltage Output Voltage / Protection (3) E358085 UL60950-1 certified CAN/CSA-C22.2 No 60950-1 certified EN60950-1 certified IEC60950-1 certified CB Report Single or Dual Notes: Note3: standard part is without continuous short circuit protection add suffix „/P“ for continuous short circuit protection Ordering Examples: RBM-1205S: 12VDC Input Voltage, 5VDC Output Voltage, Single Output RBM-0515D/P: 5VDC Input Voltage, ±15VDC Output Voltage, Dual Output with continuous short circuit protection www.recom-power.com REV.: 1/2018 ECO-1 RBM DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin und full load otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Input Voltage Range Max. ±10% 0% Minimum Load (4) Internal Operating Frequency 50kHz Output Ripple and Noise 100kHz 105kHz 20MHz BW 100mVp-p Notes: Note4: Operation below 10% load will not harm the converter, but specifications may not be met Efficiency vs. Load RBM-xx12S 100 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] RBM-xx05S 60 50 40 30 10 40 0 10 20 30 40 50 60 70 80 90 10 0 100 0 10 20 30 40 50 60 Output Load [%] Output Load [%] RBM-xx15S RBM-xx05D 100 100 90 90 80 80 70 70 60 50 40 70 80 90 100 60 50 40 30 30 3.315 0515 1215 20 10 0 3.312 0512 1212 20 Efficiency [%] Efficiency [%] 50 30 3.305 0505 1205 20 0 60 0 10 20 30 40 50 60 70 80 90 10 100 0 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] Output Load [%] www.recom-power.com 3.305 0505 1205 20 REV.: 1/2018 ECO-2 RBM DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin und full load otherwise stated) Efficiency vs. Load RBM-xx15D 100 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] RBM-xx12D 60 50 40 30 50 40 30 3.312 0512 1212 20 10 0 60 0 10 20 30 40 50 60 70 80 90 3.315 0515 1215 20 10 0 100 0 10 20 30 Output Load [%] 40 50 60 70 80 90 100 Output Load [%] REGULATIONS Parameter Condition Value Output Accuracy ±5.0% max. Line Regulation low line to high line Load Regulation ±1.2% of 1.0% Vin typ. 5Vout 12, 15Vout 10% to 100% load 15.0% max. 10.0% max. Deviation vs. Load RBM-xx05S RBM-xx12S 25 25 3.305 0505 1205 20 15 Deviation [%] Deviation [%] 15 10 5 10 5 0 0 -50 -50 -10 0 10 20 30 40 50 60 70 80 90 3.312 0512 1212 20 100 -10 Output Load [%] 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] continued on next page www.recom-power.com REV.: 1/2018 ECO-3 RBM DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin und full load otherwise stated) Deviation vs. Load RBM-xx15S 25 3.315 0515 1215 20 15 10 5 10 5 0 0 -50 -50 0 10 20 30 40 50 60 70 80 90 3.305 0505 1205 20 Deviation [%] Deviation [%] 15 -10 RBM-xx05D 25 -10 100 0 10 20 30 Output Load [%] RBM-xx12D 60 70 80 90 100 RBM-xx15D 25 3.312 0512 1212 20 15 10 5 10 5 0 0 -50 -50 0 10 20 30 40 50 60 70 80 90 3.315 0515 1215 20 Deviation [%] 15 Deviation [%] 50 Output Load [%] 25 -10 40 -10 100 0 10 20 Output Load [%] 30 40 50 60 70 80 90 100 Output Load [%] PROTECTIONS Parameter Type without suffix with suffix “/P” Short Circuit Protection (SCP) Isolation Voltage (5) Value 1 second continuous tested for 1 second rated for 1 minute I/P to O/P 3kVDC 1.5kVAC/60Hz 15GΩ min. Isolation Resistance Isolation Capacitance 20pF min. / 65pF max. Insulation Grade basic Notes: Note5: For repeat Hi-Pot testing, reduce the time and/or the test voltage Note6: Refer to local wiring regulations if input over-current protection is also required. Recommended fuse: T1A slow blow type www.recom-power.com REV.: 1/2018 ECO-4 RBM DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin und full load otherwise stated) ENVIRONMENTAL Parameter Condition Operating Temperature Range Value full load @ free air convection (see graph) -40°C to + 85°C Operating Altitude 2000m Operating Humidity non-condensing 95% RH max. Pollution Degree PD2 MTBF according to MIL-HDBK-217F, G.B. 19400 x 103 hours 7800 x 103 hours +25°C +85°C Derating Graph (@ free air convection) 100 90 Output Load [%] 80 70 60 50 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 85 Ambient Temperature [°C] SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Information Technology Equipment, General Requirements for Safety E358085-A4-UL Information Technology Equipment, General Requirements for Safety 1602031 Information Technology Equipment, General Requirements for Safety (CB) EAC E322406-A4-CB-1 RU-AT.49.09571 RoHs 2+ Standard UL60950-1, 2nd Edition:2007 CAN/CSA C22.2 No. 60950-1-03, 2nd Edition:2007 IEC60950-1:2005, 2nd Edition + A2:2013 EN60950-1:2006 + A2:2013 IEC60950-1:2005, 2nd Edition TP TC 004/2011 RoHS-2011/65/EU + AM-2015/863 DIMENSION AND PHYSICAL CHARACTERISTICS Parameter Type Value Material case potting PCB non-conductive black plastic (UL94 V-0) epoxy, (UL94 V-0) FR4, (UL94 V-0) Dimension (LxWxH) 16.55 x 6.0 x 7.7mm Weight 1.3g typ. continued on next page www.recom-power.com REV.: 1/2018 ECO-5 RBM DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin und full load otherwise stated) Dimension Drawing (mm) embossed logo Pinning information 6.0 7.7 16.55 Pin # 1 2 4 5 6 0.51+0.10/-0.05 0.25±0.05 4.10 0.51 Marking 1.90 4 5 6 5x2.54 = 12.70 1.27 Bottom View 1 2 Dual +Vin -Vin -Vout Com +Vout NC = no internal connection Tolerance: xx.x= ±0.5mm xx.xx= ±0.25mm 2.54 Recommended Footprint Details 1.00 Ø +0.15/-0 Single +Vin -Vin NC -Vout +Vout 1 2 4 5 6 Top View 2.54 PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube 520.0 x 16.0 x 9.0mm Packaging Quantity tube 30pcs Storage Temperature Range -55°C to + 125°C Storage Humidity 95% RH max. The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 1/2018 ECO-6