RD-1215D/HP

Features Unregulated Converters • • • • • • • 2W dual output converter Industry standard SIP7 packages Power sharing on outputs Optional continuous short circuit protection 1kVDC and 2kVDC basic isolation UL94 V-0 package material Efficiency up to 87% Description The RD series have been specifically designed for applications where dual power rails need to be created from a single rail supply and a low cost solution is required. With efficiencies up to 87%, the full output power is available over the operating temperature range -40°C to +85°C and the converters can be used in ambient temperatures of up to 100°C with derating. The wide selection of industry standard input voltage and output voltage options plus an input to output isolation of 1kVDC or 2kVDC makes these converters suitable for many industrial applications. DC/DC Converter RD 2 Watt SIP7 Dual Output Selection Guide Part Number nom. Input Voltage [VDC] Output Output Efficiency max. Capacitive Voltage Current typ. (1) Load (2) [VDC] [mA] [%] [µF] RD-xx05D (3,4) 5, 12, 24 ±5 ±200 75-86 ±470 RD-xx12D (3,4) 5, 12, 24 ±12 ±84 81-85 ±330 RD-xx15D (3,4) 5, 12, 24 ±15 ±66 82-86 ±330 5, 12, 24 ±24 ±42 82-86 ±100 RD-xx24D (3,4) Notes: Note1: Efficiency is tested at nominal input and full load at +25°C ambient Note2: Max Cap Load is tested at nominal input and full resistive load and is defined as the capacitive load that will allow start up in under 1s without damage to the converter EN60950-1 certified IEC60950-1 certified Model Numbering RD- __ __D/_ Input Voltage Output Voltage Protection (3) Isolation Option (4) Dual Notes: Note3: standard part is without Continuous Short Circuit Protection add suffix „/P“ for Continuous Short Circuit Protection Note4: add suffix „/H“ for 2kVDC Isolation or add suffix „/HP“ for Continuous Short Circuit Protection and 2kVDC Isolation Ordering Examples: RD-123.3D/P: 12V Input Voltage, ±3.3V Output Voltage, Dual Output with continuous short circuit protection RD-0509D/HP: 5V Input Voltage, ±9V Output Voltage, Dual Output with 2kVDC Isolation and continuous short circuit protection www.recom-power.com REV.: 1/2018 ECO-1 RD DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin and full load unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Input Voltage Range Max. ±10% 0% Minimum Load (5) Internal Operating Frequency 20kHz Output Ripple and Noise 50kHz 85kHz 20MHz BW 150mVp-p Notes: Note5: Operation below 10% load will not harm the converter, but specifications may not be met Efficiency vs. Load RD-xx12D 100 100 90 90 80 80 70 70 Efficiency [%] Efficiency [%] RD-xx05D 60 50 40 60 50 40 30 30 0505 1205 2405 20 10 0 0 10 20 30 40 50 60 70 80 90 0512 1212 2412 20 10 0 100 0 10 20 Output Load [%] 30 40 50 60 70 80 90 100 Output Load [%] RD-xx15D 100 90 Efficiency [%] 80 70 60 50 40 30 0515 1215 2415 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] www.recom-power.com REV.: 1/2018 ECO-2 RD DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin and full load unless otherwise stated) REGULATIONS Parameter Condition Value Output Accuracy ±5.0% max. Line Regulation low line to high line, full load Load Regulation RD-xx05D RD-xx12D 25 25 0505 1205 2405 20 15 10 5 10 5 0 0 -5 -5 0 10 20 30 40 50 60 70 80 90 0512 1212 2412 20 Deviation [%] Deviation [%] 15 -10 15.0% max. 10.0% max. 5Vout 12, 15 and 24Vout 10% to 100% load Deviation vs. Load ±1.2% of 1.0% Vin typ. -10 100 0 10 20 30 Output Load [%] 40 50 60 70 80 90 100 Output Load [%] RD-xx15D 25 0515 1215 2415 20 Deviation [%] 15 10 5 0 -5 -10 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] PROTECTIONS Parameter Type Short Circuit Protection (SCP) Isolation Voltage (6) Value without suffix with suffix “/P” I/P to O/P 1 second continuous without suffix tested for 1 second rated for 1 minute 1kVDC 500VAC/60Hz with suffix “/H” tested for 1 second rated for 1 minute 2kVDC 1kVAC/60Hz 10GΩ min. Isolation Resistance Isolation Capacitance 40pF min. /115pF max. Insulation Grade basic Notes: Note6: For repeat Hi-Pot testing, reduce the time and/or the test voltage Note7: Refer to local wiring regulations if input over-current protection is also required. Recommended fuse: T2A slow blow type www.recom-power.com REV.: 1/2018 ECO-3 RD DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin and full load unless otherwise stated) ENVIRONMENTAL Parameter Condition Operating Temperature Range Value full load @ free air convection (see graph) Operating Altitude -40°C to +85°C 2000m Operating Humidity non-condensing 95% RH max. Pollution Degree PD2 MTBF according to MIL-HDBK-217F, G.B. +25°C +85°C 18300 x 103 hours 8070 x 103 hours Derating Graph (@ free air convection) 100 90 Output Load [%] 80 70 60 50 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 85 Ambient Temperature [°C] SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Information Technology Equipment, General Requirements for Safety EAC 1602031 RU-AT.49.09571 RoHs 2+ Standard IEC60950-1:2005, 2nd Edition + A2:2013 EN60950-1:2006 + A2:2013 TP TC 004/2011 RoHS-2011/65/EU + AM-2015/863 DIMENSION AND PHYSICAL CHARACTERISTICS Parameter Type Value Material case potting PCB non-conductive black plastic (UL94 V-1) epoxy, (UL94 V-0) FR4, (UL94 V-0) Dimension (LxWxH) 19.65x 7.05 x 10.2mm Weight 2.8g typ. continued on next page www.recom-power.com REV.: 1/2018 ECO-4 RD DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin and full load unless otherwise stated) Dimension Drawing (mm) embossed logo 19.65 7.0 10.2 0.51 Pinning information Pin # 1 2 4 5 6 Marking Dual +Vin -Vin -Vout Com +Vout Tolerance: xx.x= ±0.5mm xx.xx= ±0.25mm 0.25±0.05 4.10 0.51+0.10/-0.05 Recommended Footprint Details 2.54 Ø1.00 +0.15/-0 2.0 1 2 1.27 Bottom View 4 5 6 1 2 4 5 6 Top View 5 x 2.54= 12.7 2.54 PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube 520.0 x 16.0 x 9.0mm Packaging Quantity tube Storage Temperature Range 25pcs -55°C to +125°C Storage Humidity 95% RH max. The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 1/2018 ECO-5