RP08-2412SASMD

Features Regulated Converters ● ● ● ● ● ● ● ● ● ● 2:1 Wide Input Voltage Range 8 Watts Regulated Output Power 1.6kVDC Isolation ULCertified Low Profile, 10.2 mm Height Over Current Protection Five-Sided Shield No Derating to 71°C Standard DIP24 and SMD-Pinning Efficiency to 85% POWERLINE DC/DC-Converter RP08S_DA Series 8 Watt DIP24 & SMD, Single & Dual Output Selection Guide 5V, 12V, 24V and 48V Input Types Part Number DIP24 (SMD) RP08-123.3SA** RP08-1205SA** RP08-1212SA** RP08-1215SA** RP08-243.3SA** RP08-2405SA** RP08-2412SA** RP08-2415SA** RP08-483.3SA** RP08-4805SA** RP08-4812SA** RP08-4815SA** RP08-1205DA** RP08-1212DA** RP08-1215DA** RP08-2405DA** RP08-2412DA** RP08-2415DA** RP08-4805DA** RP08-4812DA** RP08-4815DA** Input Range VDC 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 Output Voltage VDC 3.3 5 12 15 3.3 5 12 15 3.3 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 Output Current mA 2000 1500 666 533 2000 1500 666 533 2000 1500 666 533 ±800 ±333 ±267 ±800 ±333 ±267 ±800 ±333 ±267 Input (4) Current mA 724 801 833 843 362 396 416 416 181 198 208 208 843 833 834 427 422 411 211 206 206 Efficiency(5) Capacitive(6) Load max. % µF 80 82 84 83 80 83 84 84 80 83 84 84 83 84 84 82 83 85 83 85 85 3300 1600 350 240 3300 1600 350 240 3300 1600 350 240 ±1000 ±160 ±100 ±1000 ±160 ±100 ±1000 ±160 ±100 UL-60950-1 Certified ** add Suffix SMD for SMD package Description The A-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards. 212 14-February-2007 www.recom-international.com POWERLINE DC/DC-Converter RP08-S_DA Series RP08-4805SA 125 100 75 Output Power (%) 50 25 0 -40 -25 -10 0 Derating-Graph (Ambient Temperature) Natural Convection 50 60 70 80 90 100 Ambient Temperature Range (°C) 65 Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range (see Note 3) 12V nominal input 24V nominal input 48V nominal input 9-18VDC 18-36VDC 36-75VDC Pi Type 12V Input 24V Input 48V Input 36VDC 50VDC 100VDC 20mAp-p 600ms typ. DC-DC ON DC-DC OFF Nominal input Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V 2.5mA 8W max. ±2% 10% of full load ±0.2% Single Dual ±0.5% ±1% ±5% 50mVp-p ±0.02%/°C max. 200µs continued on next page www.recom-international.com 14-February-2007 213 Input Filter Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see Note 7) Remote OFF input current Output Power Output Voltage Accuracy (full Load and nominal Vin) Minimum Load (see Note 1) Line Regulation (low line, high line at full load) Load Regulation (25% to 100% full load) Cross Regulation (asymmetrical load 25%/100% full load) Ripple and Noise (20MHz bandwith) Temperature Coefficient Transient Response (25% load step change) POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Efficiency Isolation Voltage In to out I/O to case I/O to case RP08-S_DA Series 150% typ Continuous, automatic recovery see „Selection Guide“ table 1600VDC min. DIP type 1600VDC min. SMD type 1000VDC min. 1 GΩ min. 300pF max. 100kHz min. UL 1950, EN60950 -40°C to +85°C(with derating) +100°C -55°C to +105°C Natural convection 20°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel plated copper Non-conductive black plastic Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 DIP SMD DIP SMD Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 16g 18g 31.8 x 20.3 x 10.2mm 32.0 x 20.3 x 10.9mm 3165 x 103 hours Isolation Resistance Isolation Capacitance Operating Frequency Approved to Safety Standards Operating Temperature Range Maximum Case Temperature Storage Temperature Range Thermal Impedance Thermal Shock Vibration Relative Humidity Case Material Base Material Potting Material Conducted Emissions (see Note 8) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Weight Dimensions MTBF (see Note 2) Notes : 1. The RP08 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Start up voltage : 10VDC 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input. 8. See application notes for EMI-filtering. 214 14-February-2007 www.recom-international.com POWERLINE DC/DC-Converter Package Style and Pinning (mm) DIP24 Package Style RP08-S_DA Series 3rd angle projection 20.30 31.80 10.20 3.8 2 20.30 5.10 15.20 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin 2.54 0.25 x 0.50 Rectangular Pin 9 11 123 Bottom View 23 22 Pin Pitch Tolerance ±0.35 mm 16 14 SMD Package Style 32.00 31.40 11.20 10.90 3.81 6.35 20.30 SMD Package Style Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 2.54 21.30 25.40 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin Others NC NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC Pin area 0.1 x 0.50 12345 0.50 9 10 11 12 2.54 1.60 2.40 23.40 Bottom View 24 23 22 21 20 16 15 14 13 26.54 24.14 1 Top View Pin Pitch Tolerance ±0.35 mm 27.94 11 x 2.54 www.recom-international.com 14-February-2007 215