RP10-2405SE

Features ● ● ● ● ● ● ● ● 2:1 Wide Input Voltage Range 10 Watts Output Power 1.6kVDC Isolation UL Certified Fixed Operating Frequency Six-Sided Continuous Shield Standard 50.8 x25.4x10.2mm Package Efficiency to 86% POWERLINE DC/DC-Converter RP10S_DE Series 10 Watt 2” x 1” Package Single & Dual Output Selection Guide 12V, 24V and 48V Input Types Part Number Input Range VDC 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 Output Voltage VDC 3.3 5 12 15 3.3 5 12 15 3.3 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 Output Current mA 2000 2000 830 670 2000 2000 830 670 2000 2000 830 670 ±1000 ±416 ±333 ±1000 ±416 ±333 ±1000 ±416 ±333 Input (4) Current mA 724 1082 1064 1088 362 534 519 523 183 260 253 258 1068 1053 1041 548 520 520 267 254 260 Efficiency(5) Capacitive(6) Load max. % µF 80 81 82 81 80 82 84 84 79 84 86 85 82 83 84 80 84 84 82 86 84 6800 4700 690 470 6800 4700 690 470 6800 4700 690 470 ±680 ±330 ±110 ±680 ±330 ±110 ±680 ±330 ±110 RP10-123.3SE RP10-1205SE RP10-1212SE RP10-1215SE RP10-243.3SE RP10-2405SE RP10-2412SE RP10-2415SE RP10-483.3SE RP10-4805SE RP10-4812SE RP10-4815SE RP10-1205DE RP10-1212DE RP10-1215DE RP10-2405DE RP10-2412DE RP10-2415DE RP10-4805DE RP10-4812DE RP10-4815DE UL-60950-1 Certified M * add suffix /M2 for higher efficiencies and extended temperature range. * add /P for CTRL function with Positive Logic (1=ON, 0=OFF) P N * add /N for CTRL function with Negative Logic (0=ON, 1=OFF) Description The E-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards (9). www.recom-international.com July-2006 219 POWERLINE DC/DC-Converter RP10-S_DE Series 125 100 Derating-Graph (Ambient Temperature) 125 100 75 Output Power (%) 50 25 0 -25 -10 0 50 60 70 80 90 100 79 RP10-2405SE RP10-2405SE With Heat Sink Output Power (%) Natural Convection 75 50 25 0 -25 Natural Convection -10 0 Ambient Temperature Range (°C) Ambient Temperature Range (°C) 50 60 70 80 90 100 81 125 100 75 Output Power (%) 50 25 RP10-2405DE 125 100 RP10-2405DE With Heat Sink Output Power (%) Natural Convection 75 50 25 0 -25 Natural Convection 0 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 79 -10 0 Ambient Temperature Range (°C) 50 60 70 80 90 100 83 RP10-4805SE 125 100 75 Output Power (%) Output Power (%) 50 25 50 60 70 Ambient Temperature Range (°C) 0 -25 -10 0 80 90 100 125 100 75 RP10-2405SE_DE/M1 Natural Convection 50 25 Natural Convection 0 -40 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 85 125 100 75 Output Power (%) 50 25 RP10-4805SE/M1 125 100 RP10-2405SE_DE/M1 With Heat Sink Output Power (%) Natural Convection 75 50 25 Natural Convection 0 -40 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 85 0 -40 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 88 Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at 220 July-2006 www.recom-international.com POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input RP10-S_DE Series 9-18VDC 18-36VDC 36-75VDC Pi Type 12V Input 24V Input 48V Input 36VDC 50VDC 100VDC 30mAp-p 20ms typ. DC-DC ON DC-DC OFF DC-DC ON DC-DC OFF Nominal input Open or 3.5V < Vr < 12V Short or 0V < Vr < 1.2V Short or 0V < Vr < 1.2V Open or 3.5V < Vr < 12V 20mA 10W max. ±2% 10% of full load ±1% Single Dual ±1% ±2% ±5% Single Dual 50mVp-p 75mVp-p ±0.02%/°C max. 500µs 3.3V output 5V output 12V output 15V output 3.9V 6.2V 15V 18V 150% typ Hiccup, automatic recovery see „Selection Guide“ table 1600VDC min. 1 GΩ min. 300pF max. 300kHz typ. UL 1950, EN60950 Standard M1 -25°C to +85°C(with derating) -40°C to +85°C(non derating) +100°C -55°C to +105°C continued on next page Input Filter Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) (see Note 3) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (Optional. See Note 7) (Positive logic) (Negative logic) Remote OFF input current Output Power Output Voltage Accuracy (full Load and nominal Vin) Minimum Load (see Note 1) Line Regulation (low line, high line at full load) Load Regulation (25% to 100% full load) Cross Regulation (asymmetrical load 25%/100% full load) Ripple and Noise (20MHz bandwith) Temperature Coefficient Transient Response (25% load step change) Over Voltage Protection Zener diode clamp Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Operating Frequency Approved to Safety Standards (see Note 9) Operating Temperature Range (Reference Derating Curve) (see Note 10) Maximum Case Temperature Storage Temperature Range www.recom-international.com July-2006 221 POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Thermal Impedance (see Note 8) Thermal Shock Vibration Relative Humidity Case Material Base Material Potting Material Conducted Emissions (see Note 11) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Weight Dimensions MTBF (see Note 2) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Natural convection RP10-S_DE Series 12°C/Watt 10°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel plated copper Non-conductive black plastic Epoxy (UL94-V0) Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 27g 50.8 x 25.4 x 10.2mm 1976 x 103 hours Natural convection with Heat Sink Notes : 1. The RP10 (W) series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listedspecification. 2. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to negative input. Positive logic ON/OFF is marked with suffix-P (eg. RP10-2405SE/P) Negative logic ON/OFF is marked with suffix-N (eg. RP10-2405SE/N). If no suffix is specified, the control pin will be omitted. 8. Heat sink is optional and P/N: 7G-0020A. 9. The M1 version (RP10-xxxxSE/M1, RP10-xxxxDE/M1) does not carry the UL certification. 10.M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard version. 11. See application notes for EMI-filtering. 222 July-2006 www.recom-international.com POWERLINE DC/DC-Converter Package Style and Pinning (mm) RP10-S_DE Series 3rd angle projection 50.80 25.40 10.20 dia. 1.0 15.20 20.30 5.6 2.50 5.10 Pin Connections 3 1 2 6 Bottom View 10.20 4 10.20 5 12.70 Pin # Single 1 +Vin 2 -Vin 3 +Vout 4 No Pin 5 -Vout 6* CTRL* *Optional. See Note 7. Dual +Vin -Vin +Vout Com -Vout CTRL* Pin Pitch Tolerance ±0.35 mm www.recom-international.com July-2006 223