RP10-4812DA/P-HC

Features • • • • • • Regulated Converter 2:1 input voltage range 1.6kVDC isolation UL certified Efficiency up to 91% Six-sided continuous shield No minimum load required Description The RP10-A series are wide input voltage range 1”x1” power DC/DC converters. Despite their small size, the RP10-A converters are fully specified devices with built-in Class A EMC filters, no minimum load, 1.6kVDC isolation, under-voltage lockout and low ripple/noise figures. The outputs are fully protected against short circuits, overcurrent and overvoltage and can be trimmed over a ±10% range. The RP10-A series will find many uses in applications where board space is at a premium as no external components are required. DC/DC Converter RP10-A 10 Watt 1“ x 1“ Single and Dual Output Selection Guide Part Number Input Output Output Input (1) Efficiency (1) Max. Capacitive Voltage Range Voltage Current Current typ. Load (2) [VDC] [VDC] [mA] [mA] [%] [µF] RP10-123.3SA (2,3) 9-18 3.3 3000 994 83 3500 RP10-1205SA (2,3) 9-18 5 2000 969 86 2500 RP10-1212SA (2,3) 9-18 12 830 933 89 430 RP10-1215SA (2,3) 9-18 15 670 931 90 350 RP10-1224SA (2,3) 9-18 24 416 914 91 125 RP10-243.3SA (2,3) 18-36 3.3 3000 485 85 3500 RP10-2405SA (2,3) 18-36 5 2000 484 86 2500 RP10-2412SA (2,3) 18-36 12 830 456 91 430 RP10-2415SA (2,3) 18-36 15 670 465 90 350 RP10-2424SA (2,3) 18-36 24 416 457 91 125 RP10-483.3SA (2,3) 36-75 3.3 3000 243 85 3500 RP10-4805SA (2,3) 36-75 5 2000 239 87 2500 RP10-4812SA (2,3) 36-75 12 830 230 90 430 RP10-4815SA (2,3) 36-75 15 670 233 90 350 RP10-4824SA (2,3) 36-75 24 416 229 91 125 RP10-1205DA (2,3) 9-18 ±5 ±1000 969 86 ±1440 RP10-1212DA (2,3) 9-18 ±12 ±416 935 89 ±250 RP10-1215DA (2,3) 9-18 ±15 ±333 925 90 ±180 RP10-2405DA (2,3) 18-36 ±5 ±1000 484 86 ±1440 RP10-2412DA (2,3) 18-36 ±12 ±416 462 90 ±250 RP10-2415DA (2,3) 18-36 ±15 ±333 463 90 ±180 RP10-4805DA (2,3) 36-75 ±5 ±1000 239 87 ±1440 RP10-4812DA (2,3) 36-75 ±12 ±416 229 91 ±250 RP10-4815DA (2,3) 36-75 ±15 ±333 231 90 ±180 Notes: Note1: Maximum values at nominal input voltage and full load Note2: Max. Cap load is tested at nominal input and full resistive load E196683 UL60950-1 certified EN55032 compliant Model Numbering RP10-__ __ _A/_-_ nom. Input Voltage nom. Output Voltage “Package (4)” “CTRL Logic (3)” Single or Dual Notes: Note3: Note4: add suffix ”P” for CTRL function with positive logic (1=ON, 0=OFF) and Trim pin add suffix “N” for CTRL function with negative logic (0=ON, 1=OFF) and Trim pin or add suffix “XC” for omitted CTRL pin and Trim pin (refer to “Dimension Drawing”) add suffix “-HC” for premounted Heat-sink with clamps Ordering Examples RP10-1205SA/P = 12V input, 5V output, single, positive Logic CTRL pin RP10-4805DA/XC-HC = 48V input, ±5V output, dual, without CTRL pin, Heat-sink premounted www.recom-power.com REV.: 5/2019 PD-1 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. nom. Vin = 12VDC nom. Vin = 24VDC nom. Vin = 48VDC 9VDC 18VDC 36VDC 12VDC 24VDC 48VDC Max. Input Filter Input Voltage Range nom. Vin = 12VDC nom. Vin = 24VDC nom. Vin = 48VDC DC-DC ON DC-DC OFF 8VDC nom. Vin = 24VDC DC-DC ON DC-DC OFF 16VDC nom. Vin = 48VDC DC-DC ON DC-DC OFF 33VDC Input Surge Voltage 1s max. nom. Vin = 12VDC Under Voltage Lockout (UVLO) Pi-Type 18VDC 36VDC 75VDC 25VDC 50VDC 100VDC 9VDC 18VDC 36VDC Input Reflected Ripple Current 30mAp-p refer to “OUTPUT VOLTAGE TRIMMING” Output Voltage Trimming 3.3Vout, 12Vout Others -10% -10% Minimum Load +10% +20% 0% Power up ON/OFF CTRL Start-up Time 30ms 30ms Positive Logic DC-DC ON DC-DC OFF Open or 3.0VDC < VCTRL< 15VDC Short or 0VDC < VCTRL< 1.2VDC Negative Logic DC-DC ON DC-DC OFF Short or 0VDC < VCTRL< 1.2VDC Open or 3.0VDC < VCTRL< 15VDC -0.5mA +1.0mA ON/OFF CTRL (5) Input Current of CTRL pin DC-DC ON Standby Current DC-DC OFF 2.5mA Internal Operating Frequency 297kHz Ripple and Noise 330kHz measured at 20MHz BW, with a 10µF/25V X7R 1206 MLCC 3.3Vout, 5Vout 12Vout, 15Vout 40mVp-p 60mVp-p measured at 20MHz BW, with a 1µF/50V X7R 1206 MLCC 24Vout 60mVp-p 363kHz Notes: Note5: If suffix “XC” is specified, pin3 will be absent. If fitted, the ON/OFF control function can be positive or negative logic. The pin voltage is referenced to -Vin pin RP10-2405SA Efficiency vs. Output Current 95 Efficiency vs. Input Voltage full load 90 90 85 80 Efficiency [%] Efficiency [%] 85 75 70 65 60 18Vin 24Vin 30Vin 36Vin 55 50 45 40 10 20 30 40 50 60 70 80 90 80 75 70 65 60 100 Output Current [%] 18 20 22 24 26 28 30 32 34 36 Input Voltage [VDC] continued on next page www.recom-power.com REV.: 5/2019 PD-2 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) OUTPUT VOLTAGE TRIMMING Output Voltage Trimming Single output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for choosing these trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resistor required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below. -Vout Trim up Trim Trim down RD RU +Vout Trim RP10-xx3.3SA Trim up 1 2 3 4 5 6 7 8 9 10 [%] Vout = 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 [VDC] 385.071 191.511 126.990 94.730 75.374 62.470 53.253 46.340 40.963 36.662 [kW] 1 2 3 4 5 6 7 8 9 10 [%] RU = Trim down Vout = RD = 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 [VDC] 116.719 54.779 34.133 23.810 17.616 13.486 10.537 8.325 6.604 5.228 [kW] 2 3 4 5 6 7 8 9 10 [%] RP10-xx05SA Trim up 1 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.4 5.45 5.50 [VDC] 253.450 125.700 83.117 61.825 49.050 40.533 34.450 29.888 26.339 23.500 [kW] Vout = RU = Trim up 11 12 13 14 15 16 17 18 19 20 [%] Vout = 5.55 5.60 5.65 5.70 5.75 5.80 5.85 5.90 5.95 6.00 [VDC] 21.177 19.242 17.604 16.200 14.983 13.919 12.979 12.144 11.397 10.725 [kW] 1 2 3 4 5 6 7 8 9 10 [%] 4.95 4.90 4.85 4.80 4.75 4.70 4.65 4.60 4.55 4.50 [VDC] 248.340 120.590 78.007 56.715 43.940 35.423 29.340 24.778 21.229 18.390 [kW] 2 3 4 5 6 7 8 9 10 [%] RU = Trim down Vout = RD = RP10-xx12SA Trim up Vout = RU = 1 12.12 12.24 12.36 12.48 12.60 12.72 12.84 12.96 13.08 13.20 [VDC] 203.223 99.057 64.334 46.973 36.557 29.612 24.652 20.932 18.038 15.723 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Trim down Vout = RD = 11.88 11.76 11.64 11.52 11.40 11.28 11.16 11.04 10.92 10.8 [VDC] 776.557 380.723 248.779 182.807 143.223 116.834 97.985 83.848 72.853 64.057 [kW] RP10-xx15SA Trim up 1 2 3 4 5 6 7 8 9 10 [%] Vout = 15.15 15.30 15.45 15.60 15.75 15.90 16.05 16.20 16.35 16.50 [VDC] 161.557 78.223 50.446 36.557 28.223 22.668 18.700 15.723 13.409 11.557 [kW] Trim up 11 12 13 14 15 16 17 18 19 20 [%] Vout = 16.65 16.80 16.95 17.10 17.25 17.40 17.55 17.70 17.85 18.00 [VDC] RU = 10.042 8.779 7.711 6.795 6.001 5.307 4.694 4.149 3.662 3.223 [kW] 1 2 3 4 5 6 7 8 9 10 [%] RU = Trim down Vout = RD = 14.85 14.70 14.55 14.40 14.25 14.10 13.95 13.80 13.65 13.50 [VDC] 818.223 401.557 262.668 193.223 151.557 123.779 103.938 89.057 77.483 68.223 [kW] continued on next page www.recom-power.com REV.: 5/2019 PD-3 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) RP10-xx24SA Trim up 1 3 4 5 6 7 8 9 10 [%] 24.24 24.48 24.72 24.96 25.20 25.44 25.68 25.92 26.16 26.40 [VDC] 570.333 278.667 181.444 132.833 13.667 84.222 70.333 59.917 51.815 45.333 [kW] Vout = RU = 2 Trim up 11 12 13 14 15 16 17 18 19 20 [%] Vout = 26.64 26.88 27.12 27.36 27.60 27.84 28.08 28.32 28.56 28.80 [VDC] RU = 40.030 35.611 31.872 28.667 25.889 23.458 21.314 19.407 17.702 16.167 [kW] 1 2 3 4 5 6 7 8 9 10 [%] 23.76 23.52 23.28 23.04 22.80 22.56 22.32 22.08 21.84 21.60 [VDC] 4947.667 2439.333 1603.222 1185.167 934.333 767.111 647.667 558.083 488.407 432.667 [kW] Trim down Vout = RD = REGULATIONS Parameter Condition Value Output Accuracy ±1.0% Line Regulation low line to high line, full load Single Dual ±0.2% ±0.5% 0% to 100% load Single Dual ±0.2% ±1.0% 10% to 90% load Single Dual ±0.1% ±0.8% asymmetrical 25%100% load ±5.0% Load Regulation Cross Regulation Transient Response Recovery Time 25% load step change 250μs typ. PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) continuous, automatic recovery Over Voltage Protection (OVP) Over Load Protection (OLP) zener diode clamp 3.3Vout 5Vout 12Vout 15Vout 24Vout % of Iout rated Isolation Voltage (6) I/P to O/P I/P to O/P to case Isolation Resistance Viso= 500VDC 3.7 - 5.4VDC 6.3 - 7.4VDC 13.5 - 19.6VDC 18.3 - 22.0VDC 29.1 - 32.5VDC 150% typ., Hiccup mode 1.6kVDC/ 1 minute 1.0kVDC/ 1 minute 1GΩ min. 1500pF max. Isolation Capacitance Notes: Note6: For repeat Hi-Pot testing, reduce the time and/or the test voltage Note7: This power module is not internally fused. An input line fuse must always be used Recom suggests: 12Vin= T2A; 24Vin= T1A; 48Vin= T0.5A slow blow types www.recom-power.com REV.: 5/2019 PD-4 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) ENVIRONMENTAL Parameter Condition Value -40°C to +78°C -40°C to +100°C without derating with derating Operating Temperature Range Maximum Case Temperature +105°C Temperature Coefficient ±0.02%/K max. @ natural convection 0.1m/s, vertical direction Thermal Impedance Operating Humidity without heat-sink with heat-sink 18.2K/W 15.8K/W non-condensing 5% - 95% RH Thermal Shock according to MIL-STD-810F Vibration according to MIL-STD-810F MTBF according to MIL-HDBK-217F, G.B. +25°C 3308 x 103 hours Derating Graph (8) RP10-2405SA-HC 100 100 80 80 Output Power [%] Output Power [%] RP10-2405SA 60 40 20 0 -40 -20 0 20 40 60 78 80 60 40 20 0 -40 100 Ambient Temperature [°C] -20 0 20 40 60 80 100 81 Ambient Temperature [°C] Notes: Note8: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact RECOM Techsupport for detailed information SAFETY AND CERTIFICATIONS Certificate Type (Safety) Condition Information Technology Equipment, General Requirements for Safety E196683 EAC Standard UL60950-1, 1st Edition CAN/CSA-C22.2 No. 60950-1, 1st Edition RU-AT.49.09571 RoHS2 TP TC 004/2011 RoHS-2011/65/EU + AM-2015/863 EMC Compliance Condition Electromagnetic compatibility of multimedia equipment - Emission requirements without external filter refer to “EMC Filtering Suggestions” ESD Electrostatic discharge immunity test Air ±8kV and Contact ±6kV Standard / Criterion EN55032, Class A EN55032, Class B EN61000-4-2, Criteria A Radiated, radio-frequency, electromagnetic field immunity test 10V/m EN61000-4-3, Criteria A Fast Transient and Burst Immunity (9) ±2kV EN61000-4-4, Criteria A ±1kV EN61000-4-5, Criteria A 3Vr.m.s EN61000-4-6, Criteria A Surge Immunity (9) Immunity to conducted disturbances, induced by radio-frequency fields Power Magnetic Field Immunity 100A/m continuous; 1000A/m 1s Notes: Note9: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5 Recom suggests Nippon chemi-con KY series 220μF/100V EN61000-4-8, Criteria A continued on next page www.recom-power.com REV.: 5/2019 PD-5 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) EMC Filtering Suggestions according to EN55032 Single F1 +Vin +Vin +Vout +Vout Dual F1 +Vin +Vin C1 +Vout C1 Com -Vin -Vin -Vout -Vout -Vin -Vin -Vout +Vout Com -Vout Component List Class B MODEL C1 RP10-12xxSA, RP10-12xxDA 10μF/25V, 1812 MLCC RP10-24xxSA, RP10-24xxDA 6.8μF/50V, 1812 MLCC RP10-48xxSA, RP10-48xxDA 4.7μF/100V, 1812 MLCC DIMENSIONS and PHYSICAL CHARACTERISTICS Parameter Type Material Dimensions (LxWxH) Weight Value case base potting without Heat-sink with Heat-sink copper alloy C2680 FR4 PCB epoxy (UL94 V-0) 25.4 x 25.4 x 9.9mm 31.4 x 25.4 x 16.5mm without Heat-sink with Heat-sink 16.5g 23g Dimension Drawing (mm) Pinning Information Pin # 1 2 3 4 5 6 25.4 5.6 9.9 25.4 2.54 8 x 2.54= 20.32 Ø 1.0±0.1 Recommended Footprint Details 2 Bottom View 3 5 3 2 1 Dual +Vin -Vin CTRL (3) +Vout Com -Vout “/XC“ +Vin -Vin no Pin (3) +Vout Trim -Vout Pin Pitch Tolerance ±0.25mm Tolerance:  xx.x= ±0.5mm  xx.xx= ±0.25mm 6 2.54 2.54 1 12.70 7.62 4 10.2 5.08 2.54 Single +Vin -Vin CTRL (3) +Vout Trim -Vout Top View 5 4 6 continued on next page www.recom-power.com REV.: 5/2019 PD-6 RP10-A DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) Dimension Drawing with Heat-sink (mm) 25.4 25.4 Top View Heat-sink Pinning Information 24.2 Pin # 1 2 3 4 5 6 5.6 16.5 9.9 5.85 31.4 2.54 8 x 2.54= 20.32 Ø 1.0±0.1 Recommended Footprint Details 2 Bottom View 3 1 “/XC“ +Vin -Vin no Pin (3) +Vout Trim -Vout Pin Pitch Tolerance ±0.25mm Tolerance:  xx.x= ±0.5mm  xx.xx= ±0.25mm 2.54 2 5 Dual +Vin -Vin CTRL (3) +Vout Com -Vout 6 3 2.54 1 12.70 7.62 4 10.2 5.08 2.54 Single +Vin -Vin CTRL (3) +Vout Trim -Vout Top View 5 4 6 PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube tray without heat-sink with heat-sink 257.0 x 28.5 x 21.0mm 230.0 x 180.0 x 28.0mm Packaging Quantity tube tray without heat-sink with heat-sink 8pcs 20pcs Storage Temperature Range Storage Humidity -55°C to +125°C non-condensing 5% - 95% RH The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 5/2019 PD-7 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: RECOM: RP10-4805SA/P RP10-1215SA/N RP10-1205DA/P-HC RP10-2405SA/P RP10-1224SA/P-HC RP10-243.3SA/N-HC RP10-4815DA/XC RP10-1215DA/XC RP10-2412SA/XC RP10-2415DA/XC RP10-4815SA/XC-HC RP101215DA/XC-HC RP10-4812DA/N RP10-1212SA/N-HC RP10-123.3SA/XC RP10-4812SA/XC RP10-4824SA/XC-HC RP10-243.3SA/XC RP10-4812DA/XC RP10-4812SA/XC-HC RP10-2412DA/XC-HC RP10-1205SA/XC RP104805DA/XC RP10-2405DA/N-HC RP10-2424SA/N RP10-2415DA/XC-HC RP10-4812DA/XC-HC RP10-1212DA/XCHC RP10-1212DA/XC RP10-4815SA/XC RP10-243.3SA/N RP10-4812DA/P RP10-483.3SA/N-HC RP10-4815SA/PHC RP10-2412DA/N RP10-2405SA/N-HC RP10-2405SA/XC RP10-1205DA/XC-HC RP10-2415SA/XC-HC RP10483.3SA/XC-HC RP10-2412SA/XC-HC RP10-4805DA/XC-HC RP10-1205DA/XC RP10-1212SA/N RP10-2424SA/XC RP10-1212SA/XC-HC RP10-483.3SA/XC RP10-4805SA/XC-HC RP10-123.3SA/XC-HC RP10-1215SA/XC RP101224SA/XC-HC RP10-4815DA/XC-HC RP10-1224SA/XC RP10-4824SA/XC RP10-243.3SA/XC-HC RP104805SA/XC RP10-2415SA/XC RP10-2415SA/N RP10-4812SA/N-HC RP10-483.3SA/N RP10-2412DA/P-HC RP102412DA/XC RP10-2405DA/XC RP10-2405DA/XC-HC RP10-1212SA/XC RP10-123.3SA/P-HC RP10-2424SA/XC-HC RP10-4815SA/N-HC RP10-1212DA/P RP10-4824SA/N-HC RP10-1212SA/P RP10-4815DA/N RP10-123.3SA/N RP10-1205SA/P-HC RP10-2424SA/P RP10-1215SA/XC-HC RP10-2405SA/XC-HC RP10-1205SA/XC-HC RP102412DA/P RP10-1215DA/N RP10-2415DA/P RP10-4815DA/P RP10-1215DA/N-HC RP10-2405DA/N RP101205DA/N-HC RP10-4805DA/P-HC RP10-2415DA/N RP10-2405DA/P RP10-2424SA/N-HC RP10-4805SA/N-HC RP10-2405DA/P-HC RP10-2415DA/P-HC RP10-2412SA/N RP10-1205SA/N-HC RP10-1205DA/P RP10-1215DA/P RP10-4812SA/N RP10-1205SA/P RP10-4805DA/N-HC RP10-4815DA/N-HC